Frigidaire FASG7021NW Installation Instructions (All Languages)
Frigidaire FASG7021NW Manual
View all Frigidaire FASG7021NW manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire FASG7021NW manual content summary:
- Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 1
All about the Installation of your Dryer TA B L E O F C O N T E N T S Important Safety Instructions ...2-3 Installation Requirements ...4-10 Installed Dryer Dimensions ...11 Installation Instructions ...12-19 Reversing Door ...20-23 Accessories ...24 Français...25 Español ...49 137441900A (1104) - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 2
or in Canada, the Canadian electrical code C22.1 part 1. • The gas service to the dryer must conform with local codes and ordinances and the latest edition of the National Fuel Gas Code ANSI Z223.1, or in Canada, CAN/ACG B149.1-2000. An individual manual shut-off valve must be installed within 6 ft - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 3
to avoid possible injury or death. Gas Supply (Gas Dryer) Manual shutoff valve present in supply Electric Supply (Electric Dryer) Approved NEMA 10-30R or 14-30R service cord with all instructions in this guide Test hinge and latch for function Electrical Power House power turned on Dryer - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 4
this dryer with power created by gas powered dryer is internally grounded to neutral unless it was manufactured for sale in Canada. Only a 4-conductor cord shall be used when the appliance dryers. For 4-wire cord connection instructions see ELECTRICAL CONNECTIONS FOR A 4-WIRE SYSTEM. Í NOTE Dryers - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 5
kPa). 7 The dryer MUST be isolated from the gas supply piping system during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.45 kPa). 8 Connections for the gas supply must comply with the Standard for Connectors for Gas Appliances, ANSI Z21.24 - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 6
any other obstruction. WARNING FIRE HAZARD Failure to follow these instructions can create excessive drying times and fire hazards. Correct Incorrect obstruct clothes dryer airflow and increase the risk of fire. If your present system is made up of plastic duct or metal foil duct, replace it with - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 7
will be expelled into the laundry area. An accumulation of lint in any area of the home can create a health and fire hazard. The dryer must be connected to an exhaust outdoors. Regularly inspect the outdoor exhaust opening and remove any accumulation of lint around the outdoor exhaust opening and - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 8
Exhaust direction Directional exhausting can be accomplished by installing a quick-turn 90° dryer vent elbow directly to exhaust outlet of dryer. Dryer vent elbows are available through your local parts distributor or hardware store. CORRECT INCORRECT In installations where the exhaust system is - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 9
Part 280) or Standard CAN/CSAZ240 MH. 2 Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support to previous sections in this guide for other important exhaust venting system requirements. 5 When installing a gas dryer into a mobile home, a - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 10
or closet, MUST be exhausted outdoors. 2 No other fuel burning appliance shall be installed in the same closet as the gas dryer. 3 Your dryer needs the space around it for proper ventilation. DO NOT install your dryer in a closet with a solid door. 4 Closet door ventilation required: A minimum - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 11
) electrical supply on rear of unit 51.25" (130cm) centerline height for rear vent 3.7" (9.5cm) freestand dryer on floor floor line gas supply pipe on rear of gas unit 1.6" (4cm) dryer mounted on optional pedestal 16.9" (43cm) 19.0" (48cm) floor line * To obtain these minimal depth dimensions - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 12
wired power cord with a copper wired receptacle. WARNING ELECTRICAL SHOCK HAZARD • This appliance MUST be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. • Do not use an extension cord with this - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 13
a licensed electrician. 3 DO NOT modify the plug provided with this appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. Grounding requirements - Gas dryer (USA and Canada) 1 The dryer is equipped with a three-prong (grounding) plug for your protection - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 14
INSTRUCTIONS Gas connection 1 Remove the shipping cap from gas pipe at the rear of the dryer. 3 Open the shutoff valve in the gas supply line to allow gas to flow through the pipe. Wait a few minutes for gas to move through the gas line. to d IMPORTANT DO NOT connect the dryer to L.P. gas service - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 15
INSTRUCTIONS Water connection (Steam Model only) WATER SUPPLY REQUIREMENTS Cold water faucet MUST be installed within 42 inches (107 cm) of your dryer Remove COLD inlet hose from COLD water supply and inspect for rubber washer. Replace washer if it is torn or worn out. RUBBER WASHER MUST BE PRESENT - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 16
INSTALLATION INSTRUCTIONS Water connection, continued (Steam Model only) 5 If your by hand; then tighten it another 2/3 turn with pliers. DIRECT CONNECTION OR WITH EXTENSION* WATER INLET ON DRYER Í NOTE If you were able to install the "Y" connector directly to the COLD water supply, please - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 17
the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel. At this time, the strain relief should - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 18
the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel. At this time, the strain relief should - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 19
time and money. 6 If you have any questions during initial operation, please review the "Avoid Service Checklist" in your Use & Care Guide before calling for service. 7 Place these instructions in a location near the dryer for future reference. Í NOTE A wiring diagram and technical data sheet are - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 20
then upper screw. 4 Gently place dryer door face down on flat, covered work surface. 5 Locate the 5 indented head screws (no. 1-5) in the small, circular recesses (at 11, 1, 4, 6, and 8 o'clock positions) of the inner door. Remove and save these 5 screws. 3 Supporting door with both hands, squarely - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 21
REVERSING DOOR Reversing the hinge 1 Carefully pull out the 2 small round hole plugs from the front panel and save. Remove and save the square "T" slot cover by sliding it up and pulling it out. Move all 3 plugs to the opposite side of the front panel and insert. 4 From the back side of the inner - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 22
right-hand hinge. 3 Replace indented head screws (no. 1-5) removed earlier. Take care not to strip out the plastic holes. 4 Replace pan head screws ( on the supports for the hinge cutout cover. Pivot the inner door down onto the outer door. 5 Locate new metal strike supplied with dryer manuals. Grip - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 23
align the mounting holes. "T" POST ON DOOR HINGE "T" SLOT IN FRONT PANEL 3 Close the door and test operation of hinge, strike and latch. 2 While supporting the door, install the upper pan head screw first and then the lower one. Í NOTE Correctly installed hinge screws will press hinge flush to front - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 24
you purchased your dryer. Replacement parts: If replacements parts are needed for your washer, contact the source where you purchased your washer or refer to your Use and Care Guide for more information. WARNING ELECTRICAL SHOCK HAZARD Label all wires prior to disconnection when servicing controls - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 25
Installation de votre Tout - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 26
MESURES DE SÉCURITÉ IMPORTANTES AVERTISSEMENT Pour votre sécurité, l'information contenue dans ces instructions doit être suivie afin de réduire les risques d'incendie ou d'explosion ou pour prévenir les dommages matériels, les blessures ou la mort. Vous ne - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 27
MESURES DE SÉCURITÉ IMPORTANTES AVERTISSEMENT Veuillez lire ces instructions au complet avant d'utiliser le sécheuse. Liste de vérification d' les étiquettes de sécurité. Les mesures de sécurité présentées dans ce guide sont identifiées par le mot AVERTISSEMENT ou ATTENTION selon le type de risque pré - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 28
EXIGENCES D'INSTALLATION Í REMARQUE Étant donné les variations de tension possibles, l'utilisation de cette sécheuse avec une source d'alimentation produite par une génératrice - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 29
EXIGENCES D'INSTALLATION Exigences électriques de la sécheuse - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 30
po) entre le bas de la bouche d'évacuation et le sol ou toute autre obstruction. AVERTISSEMENT RISQUE D'INCENDIE Le non-respect de ces instructions pourrait augmenter démesurément les temps de séchage et entraîner des risques d'incendie. Correct Incorrect Vous trouverez ci-dessous les exigences - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 31
EXIGENCES D'INSTALLATION Exigences de système d'évacuation (suite) AVERTISSEMENT RISQUE D'INCENDIE Une sécheuse doit être évacuée vers l'extérieur. N'évacuez pas une sécheuse dans une cheminée, un mur, un plafond, un grenier, un vide sanitaire ou dans tout espace clos d'un bâtiment. La sécheuse - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 32
EXIGENCES D'INSTALLATION Exigences de système d'évacuation (suite) Installez les raccords mâles dans le bon sens : Direction d'évacuation Il est possible de diriger l'évacuation en posant un coude de 90° - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 33
EXIGENCES D'INSTALLATION Installation dans une maison usinée ou mobile 1 L'installation DOIT être conforme - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 34
EXIGENCES D'INSTALLATION Exigences de dégagement (suite) Installation dans un Endroit en Retrait ou une Armoire 1 Une sécheuse installée dans une chambre - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 35
DIMENSIONS DE L'INSTALLATION DE SÉCHEUSE 51.4" (131cm) Avec la porte grande ouverte 30.3" (77cm)* À partir de l'avant de la porte lorsqu'elle est fermée 27.0" (68.5cm) 36.0" (91.5cm) Alimentation électrique - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 36
électrique Vous trouverez ci-dessous les exigences pour l'installation électrique adéquate et sécuritaire de votre appareil. Le non-respect de ces instructions pourrait entraîner le risque de choc ou d'incendie. AVERTISSEMENT RISQUE DE CHOC ÉLECTRIQUE • Un réducteur de tension certifié UL doit être - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 37
INSTRUCTIONS D'INSTALLATION Exigences de mise - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 38
INSTRUCTIONS D'INSTALLATION Connexion de gaz 1 Retirez le capuchon d'expédition de la conduite de gaz - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 39
INSTRUCTIONS D'INSTALLATION Raccordement d'eau (modèles - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 40
INSTRUCTIONS D'INSTALLATION Raccordement d'eau, suite (modèles - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 41
INSTRUCTIONS D'INSTALLATION Connexion électrique (sauf au Canada) - cordon - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 42
INSTRUCTIONS D'INSTALLATION Connexion électrique (sauf au Canada) - cordon - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 43
INSTRUCTIONS D'INSTALLATION Installation (générale) 1 Branchez la conduite d'évacuation au système d'évacuation extérieur (reportez-vous aux pages 30 - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 44
INVERSION DE LA PORTE Dépose de la porte 1 Protégez la surface de travail, comme le dessus de la sécheuse ou le plancher près de la sécheuse, avec un chiffon doux ou une serviette. 2 Ouvrez la porte de la sécheuse et retirez les deux vis de la charnière. Enlevez d'abord la vis du bas, puis la vis du - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 45
INVERSION DE LA PORTE Inversion de la charnière 1 Enlevez délicatement les 2 petits bouchons circulaires qui se trouvent sur le panneau avant et conservezles. Retirez le protecteur carré de la fente en « T » en le faisant glisser vers le haut et en le tirant vers l'extérieur, puis conservez-le. - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 46
INVERSION DE LA PORTE Remontage de la porte 1 Soulevez l'anneau de la vitre interne. Faites-le tourner de 180 degrés, réinstallez-le sur la porte externe, alignez les marques « LH » (pour la charnière de poignée - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 47
INVERSION DE LA PORTE Remise en place de la porte 1 En tenant la porte - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 48
ACCESSOIRES SOCLE DE RANGEMENT ASSORTI* Socle Socle Socle Socle Socle Blanc -PIÈCE N° CFPWD15W Bleu - PIÈCE N° CFWD15RN Rouge - PIÈCE N° CFWD15R Argentés - PIÈCE N° CFWD15A Noir - PIÈCE N° CFWD15B ATTENTION Tout défaut d'utiliser les accessoires fabriqués ou certifiés par le fabricant pourrait entra - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 49
de su Secadora Dryer All about Todo acerca thedel ÍNDICE Instrucciones importantes de seguridad ...50-51 Requisitos de instalación ...52-58 Dimensiones de la secadora instalada ...59 Instrucciones de instalación ...60-67 Inversión de la puerta...68-71 Accesorios ...72 www.frigidaire.com EE. USAUU - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 50
del Código Eléctrico de Canadá (Canadian Electrical Code) Parte 1. • El servicio de gas de la electrodoméstico debe cumplir con los códigos y las de cierre individual manual a una distancia no mayor a 1,83 m (6 pies) de la secadora de conformidad con el Código Nacional de Gas Combustible ANSI Z223.1/ - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 51
á nivelada de lado a lado y de adelante hacia atrás El secadora descansa firmemente sobre sus cuatro esquinas Suministro de gas (secadora a gas) Válvula de cierre manual instalada en la tubería de suministro Todas las conexiones selladas con un sellante aprobado y bien apretadas con una llave - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 52
DE INSTALACIÓN Í NOTA Debido a posibles variaciones en el voltaje, no se recomienda utilizar esta secadora con electricidad generada a partir de generadores a gas, solares, eólicos ni de ninguna otra clase que no sean los empleados por su empresa de electricidad local. Requisitos eléctricos de la - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 53
instalación DEBE realizarse de acuerdo con los códigos locales o, en ausencia de ellos, con el Código de Gas Nacional (National Fuel Gas Code), ANSI Z223.1 (última edición). 2 La línea de suministro de gas debe ser un tubo de 1,27 cm (1/2 pulgada). 3 Si los códigos lo permiten, se puede utilizar un - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 54
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape Utilice solo un conducto de metal flexible o rígido de 102 mm (4 pulgadas) de diámetro (mínimo) y una capucha de ventilación aprobada que tenga uno o más reguladores de tiro que se abran cuando la secadora esté en funcionamiento. Cuando la - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 55
de incendio. • No bloquee los extremos de escape del sistema de ventilación, ni utilice tornillos, remaches ni otros sujetadores que se extiendan hacia la parte interna del conducto para ensamblarlo. Es posible que la pelusa quede atrapada en el filtro, los tornillos o los remaches, lo que puede - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 56
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape (continuación) Instale los accesorios macho en la dirección correcta: Dirección del escape El escape direccional se puede lograr mediante la instalación de un codo de ventilación de giro rápido de 90° directamente en la salida de la - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 57
Norma de Seguridad y Construcción de Casas Rodantes, título 24 CFR, Parte 32-80 (que anteriormente se conocía como la Norma Federal de Seguridad las secciones anteriores de esta guía. 5 Cuando se instale una secadora a gas en una casa rodante, se debe dejar espacio en el exterior para la salida - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 58
otro artefacto de combustión en el mismo armario que la secadora a gas. 3 La secadora necesita espacio a su alrededor para que la ventilaci ón distribuidas uniformemente en toda la superficie. Alcôve LATERALES PARTE TRASERA PARTE SUPERIOR PARTE DELANTERA 0 cm (0") 0 cm (0") 0 cm (0") 0 cm - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 59
trasera de la unidad 51.25" (130cm) secadora independiente sobre el piso línea del piso tubería de suministro de gas en la parte trasera de la unidad de gas altura de la línea central para ventilación trasera 3.7" (9.5cm) 1.6" (4cm) secadora colocada sobre pedestal opcional 16.9" (43cm) 19 - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 60
INSTRUCCIONES DE INSTALACIÓN Instalación eléctrica Los siguientes son requisitos necesarios para la instalación eléctrica segura y correcta de su secadora. El no seguir estas instrucciones puede producir una descarga eléctrica y/o incendio. ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA • Debe - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 61
. Si no calza en el tomacorrientes, pídale a un electricista calificado que instale un tomacorrientes adecuado. Requisitos de conexión a tierra: secadora a gas (Estados Unidos y Canadá) 1 La secadora está equipada con un enchufe de tres patas (conexión a tierra) para evitar el peligro de electrocuci - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 62
diámetro interior desde la línea de suministro de gas al tubo de 0,96 cm (3/8 pulgada) ubicado en la parte trasera de la secadora. Utilice un reductor de 1, licuados en todas las conexiones de los tubos. FLUJO DE GAS Válvula Conector de cierre manual doble Conector doble la s eca do ra de sde - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 63
INSTRUCCIONES DE INSTALACIÓN Conexión de agua (modelo al vapor solamente) REQUISITOS DE LA ENTRADA DE AGUA Los grifos de agua fría DEBEN instalarse a una distancia no mayor de 107 cm (42 pulgadas) de la entrada de agua de secadora. Los grifos DEBEN estar a 1,9 cm (3/4 pulgadas) con roscas para la - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 64
a la otra salida del conector en "Y" y apriételo a mano. Conecte el codo de 90° de la manguera a la admisión de agua de latón en la parte trasera de la secadora y apriételo a mano. Apriete todas las conexiones de la manguera de admisión de agua de la secadora 2/3 de vuelta más usando alicates - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 65
del tomacorriente. 2 Extraiga el tornillo que sujeta la cubierta de acceso del bloque terminal que se encuentra en la esquina inferior de la parte trasera de la secadora. 3 Instale un dispositivo de liberación de tensión aprobado por U.L., de acuerdo con las instrucciones relativas al cable de - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 66
del tomacorriente. 2 Extraiga el tornillo que sujeta la cubierta de acceso del bloque terminal que se encuentra en la esquina inferior de la parte trasera de la secadora. 3 Instale un dispositivo de liberación de tensión aprobado por U.L., de acuerdo con las instrucciones relativas al cable de - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 67
cuidadosamente. Ajuste una o varias de las patas de la secadora hasta que se encuentre firme sobre las cuatro patas. Coloque un nivel en la parte superior de la secadora. La secadora DEBE estar nivelada y firme sobre las cuatro patas. Presione las distintas esquinas para asegurarse de que la secadora - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 68
INVERSIÓN DE LA PUERTA Cómo extraer la puerta 1 Proteja las superficies de trabajo planas, como la parte superior de la secadora o el piso cerca de ésta utilizando un paño o toalla suave. 2 Abra la puerta de la secadora y retire los dos tornillos de - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 69
ranura en forma de "T" deslizándola hacia arriba y tirando de ella para retirarla. Mueva los 3 tapones al lado opuesto del panel delantero. 4 Desde la parte trasera de la puerta interior, presione las lengüetas de retención del tapón de plástico cuadrado para liberarlo. Guarde el tapón cuadrado para - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 70
de la cubierta de la bisagra. Gire la puerta interior hacia abajo sobre la puerta exterior. 5 Ubique el nuevo pestillo de metal proporcionado con los manuales de la secadora. Sostenga el pestillo nuevo con alicates como se muestra abajo. Inserte firmemente el pestillo de manera que quede en posici - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 71
ÓN DE LA PUERTA Reinstalación de la puerta 1 Mientras sostiene la puerta con ambas manos, introduzca la pieza en forma de "T" que se encuentra en la parte trasera de la bisagra en la ranura en forma de "T" del panel delantero y baje la puerta para alinear los agujeros de instalación. PIEZA EN FORMA - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 72
que adquirió no incluye un kit de instalación sobre la lavadora o desea un kit diferente, puede pedir uno. KIT DE CONVERSIÓN A GAS LP Pieza No. PCK4200 15.0 (38 c " m) Las secadoras a gas diseñadas para el uso en lugares con suministro de LP requieren utilizar un kit de conversión antes de la - Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 73
- Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 74
- Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 75
- Frigidaire FASG7021NW | Installation Instructions (All Languages) - Page 76
All about the
Installation
of your
Dryer
137441900A (1104)
TABLE OF CONTENTS
Important Safety Instructions
..............................
2-3
Installation Requirements
.................................
4-10
Installed Dryer Dimensions
..................................
11
Installation Instructions
..................................
12-19
Reversing Door
..............................................
20-23
Accessories
.........................................................
24
Français
..............................................................
25
Español
..............................................................
49