Frigidaire FASG7073LA Installation Instructions (All Languages)
Frigidaire FASG7073LA Manual
UPC - 012505382635
View all Frigidaire FASG7073LA manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire FASG7073LA manual content summary:
- Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 1
All about the Installation of your Dryer TABLE OF CONTENTS Important Safety Instructions 2-3 Reversing Door 18-21 Installation Requirements 4-10 Accessories 22 Installed Dryer Dimensions 11 Français 23 Installation Instructions 12-17 Español 45 137336500A (1003) - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 2
for gas supply (gas dryer) • LP-resistant thread tape (for natu- ral gas or LP supply, gas dryer) • Carpenter's level • External vent hood • 4-inch (102 mm), rigid metal or semi-rigid metal exhaust duct work • 3-wire or 4-wire 240 volt cord kit (electric dryer) • 4 in. (10.2 cm) clamp • Gas line - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 3
240v Electric Supply (Electric Dryer) Approved NEMA 10-30R or 14-30R service cord with all screws tight on terminal block Approved strain relief installed Terminal access cover installed before initial operation Door Reversal Follow detailed instructions in this guide Test hinge and latch - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 4
this dryer with power created by gas powered open end spade lug connectors with upturned ends or closed loop connectors and marked for use with clothes dryers. For 3-wire cord connection instructions see ELECTRICAL CONNECTIONS FOR A 3-WIRE SYSTEM. 4-WIRE POWER SUPPLY CORD KIT (not supplied) 4-wire - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 5
INSTALLATION REQUIREMENTS Electrical requirements for gas dryer CIRCUIT - Individual, properly polarized and grounded 15 amp. branch circuit fused with 15 amp. time delay fuse or circuit breaker. POWER SUPPLY - 2-wire, with ground, 120 volt, single phase, 60 Hz, Alternating Current. POWER SUPPLY - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 6
hood which has a swing-out damper(s) that open when the dryer is in operation. When the dryer stops, the dampers automatically close to prevent drafts any other obstruction. WARNING FIRE HAZARD Failure to follow these instructions can create excessive drying times and fire hazards. The following - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 7
any area of the home can create a health and fire hazard. The dryer must be connected to an exhaust outdoors. Regularly inspect the outdoor exhaust opening and remove any accumulation of lint around the outdoor exhaust opening and in the surrounding area. WARNING FIRE HAZARD Exceeding the length of - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 8
an increase in vent restriction. • The exhaust system should be inspected and cleaned a minimum of every 18 months with normal usage. The more the dryer is used, the more often you should check the exhaust system and vent hood for proper operation. See also CLEARANCE REQUIREMENTS on the next page - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 9
CAN/CSAZ240 MH. 2 Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support combustion. Metal ducting to previous sections in this guide for other important exhaust venting system requirements. 5 When installing a gas dryer into a mobile home, - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 10
be installed in the same closet as the gas dryer. 3 Your dryer needs the space around it for proper ventilation. DO NOT install your dryer in a closet with a solid door. 4 Closet door ventilation required: A minimum of 120 square inches (774.2 cm²) of opening, equally divided at the top and bottom - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 11
) to installation depth. Downward venting of exhaust on pedestal-mounted dryer adds approximately 2.25 in. (5.7 cm) to installation depth. 51.4" (131cm) to clear open door 30.3" (77cm)* to front of closed door gas supply pipe on rear of gas unit 1.6" (4cm) 16.9" (43cm) 3.75" (9.5cm) 13.50" (34 - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 12
dryer is not properly grounded. Follow the instructions in this manual for proper grounding. • Do not use an extension cord with this dryer ed electrician. For a permanently connected dryer: 1 The dryer MUST be connected to a grounded metal, permanent wiring system; or an equipment grounding - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 13
INSTALLATION INSTRUCTIONS Grounding requirements - Electric dryer (Canada) WARNING ELECTRICAL SHOCK HAZARD proper outlet installed by a qualified electrician. Grounding requirements - Gas dryer (USA and Canada) 1 The dryer is equipped with a three-prong (grounding) plug for your protection - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 14
INSTALLATION INSTRUCTIONS Gas connection 1 Remove the shipping cap from gas pipe at the rear of the dryer. IMPORTANT DO NOT connect the dryer to L.P. gas service without converting the gas valve. An L.P. conversion kit must be installed by a qualified gas technician. 2 Connect a 1/2 inch (1.27 cm) - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 15
INSTRUCTIONS Electrical connection (non-Canada) - 3 wire cord 3-wire receptacle (NEMA type 10-30R) WARNING ELECTRICAL SHOCK HAZARD Failure to disconnect power source before servicing 3-wire system!! Neutral terminal IMPORTANT If moving dryer from a 4-wire system and installing it in a 3-wire - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 16
INSTRUCTIONS Electrical connection (non-Canada) - 4 wire cord 4-wire receptacle (NEMA type 14-30R) WARNING ELECTRICAL SHOCK HAZARD Failure to disconnect power source before servicing dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 17
6 If you have any questions during initial operation, please review the "Avoid Service Checklist" in your Use & Care Guide before calling for service. 7 Place these instructions in a location near the dryer for future reference. Í NOTE A wiring diagram and technical data sheet are located inside the - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 18
1 Protect flat work surface, such as top of dryer or floor near dryer, with a soft cloth or towel. 2 Open dryer door and remove the two hinge screws. Remove lower screw first, then upper screw. 4 Gently place dryer door face down on flat, covered work surface. 5 Locate the 5 indented head screws (no - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 19
pinch the retaining tabs of the plastic square plug to release it. Save square plug for reinstallation. SQUARE PLUG ROUND PLUG 2 Turn inner door assembly over to expose retaining tabs of metal strike. Grip tabs fully with pliers to remove. Discard old metal strike. 5 Carefully remove the 2 round - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 20
out the plastic holes. no. 1-5 no. 6-7 2 Rest the opening of the inner door at a 90 degree angle on the supports for the hinge cutout cover. Pivot the inner door down onto the outer door. 5 Locate new metal strike supplied with dryer manuals. Grip new strike with pliers as shown below. Firmly - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 21
on the front panel and lower it to align the mounting holes. "T" POST ON DOOR HINGE "T" SLOT IN FRONT PANEL REVERSING DOOR 3 Close the door and test operation of hinge, strike and latch. 2 While supporting the door, install the upper pan head screw first and then the lower one. Í NOTE Correctly - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 22
included in the initial purchase of your dryer. If your model did not include a stacking kit or you desire another stacking kit, you may order one. LP CONVERSION KIT P/N PCK4200 Gas dryers intended for use in a location supplied with LP must use a conversion kit prior to installation. MOBILE HOME - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 23
Tout à propos de Installation de votre Sécheuse TABLE DES MATIÈRES Mesures de sécurité importantes 24-25 Instructions d'installation 34-39 Exigences d'installation 26-32 Inversion de la porte 40-43 Dimensions, appareil install 33 Accessoires 44 - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 24
service ou le fournisseur de gaz. • Installez l'appareil conformément aux instructions glements locaux ainsi qu'à la toute dernière édition du Fuel Gas Code (ANSI Z223.1), ou au Canada, au CAN/ACG B149.1- autre laveuse. • Les instructions comprises dans ce guide et toute autre documentation fournie - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 25
certifié est installé Le couvre-borne est installé avant la première mise en marche Inversion de la porte Suivez les instructions détaillées contenues dans ce guide Vérifiez que la charnière et le loquet fonctionnent correctement Alimentation en électricité Le système électrique de la maison - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 26
toute autre source d'alimentation différente de celle fournie par les services publics n'est pas recommandée. Exigences électriques de la sécheuse spécialement indiqués pour une utilisation avec une sécheuse. Pour les instructions de raccordement du cordon à 3 fils, consultez la section CONNEXIONS É - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 27
canalisation de gaz à des pressions égales ou inférieures à 3,45 kPa (1/2 lb/po2). 8 Les branchements d'alimentation en gaz doivent être conformes à la norme Connectors for Gas Appliances (Raccords pour appareils au gaz) ANSI Z21.24. 27 - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 28
po) entre le bas de la bouche d'évacuation et le sol ou toute autre obstruction. AVERTISSEMENT RISQUE D'INCENDIE Le non-respect de ces instructions pourrait augmenter démesurément les temps de séchage et entraîner des risques d'incendie. Vous trouverez ci-dessous les exigences pour l'utilisation ad - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 29
EXIGENCES D'INSTALLATION Exigences de système d'évacuation (suite) AVERTISSEMENT RISQUE D'INCENDIE Une sécheuse doit être évacuée vers l'extérieur. N'évacuez pas une sécheuse dans une cheminée, un mur, un plafond, un grenier, un vide sanitaire ou dans tout espace clos d'un bâtiment. La sécheuse - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 30
EXIGENCES D'INSTALLATION Exigences de système d'évacuation (suite) Installez les raccords mâles dans le bon sens : Direction d'évacuation Il est possible de diriger l'évacuation en posant un coude de 90° à courbe immédiate directement à la sortie d'évacuation de la sécheuse. Les coudes pour é - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 31
à l'extérieur de la cloison et être fixé solidement à la structure de la maison. 4 Reportez-vous aux sections précédentes de ce guide relativement aux autres exigences d'évacuation importantes. 5 Lors de l'installation d'une sécheuse à gaz dans une maison mobile, des dispositions doivent être prises - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 32
EXIGENCES D'INSTALLATION Exigences de dégagement (suite) Installation dans un Endroit en Retrait ou une Armoire 1 Une sécheuse installée dans une chambre à coucher, une salle de bains, un renfoncement ou un placard DOIT être évacuée vers l'extérieur. 2 Aucun autre appareil à combustion ne doit ê - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 33
51.4" (131cm) Avec la porte grande ouverte DIMENSIONS DE L'INSTALLATION DE SÉCHEUSE 30.3" (77cm)* À partir de l'avant de la porte lorsqu'elle est fermée 27.0" (68.5cm) 36.0" (91.5cm) 51.25" (130cm) Sécheuse autonome sur le plancher Plancher Alimentation en gaz à l'arrière de l'appareil à gaz - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 34
équatement mis à la terre. La mise à la terre inadéquate de la sécheuse pourrait entraîner des risques de choc électrique. Suivez les instructions de ce guide pour une mise à la terre adéquate. • N'utilisez pas de rallonge avec cet appareil. Certains cordons prolongateurs ne sont pas conçus pour la - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 35
INSTRUCTIONS D'INSTALLATION Exigences de mise à la terre - Sécheuse électrique (Canada) AVERTISSEMENT RISQUE DE CHOC ÉLECTRIQUE Un raccordement inadéquat du conducteur de mise à la terre de l'é - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 36
INSTRUCTIONS D'INSTALLATION Connexion de gaz 1 Retirez le capuchon d'expédition de la conduite de gaz à l'arrière de l'appareil. IMPORTANT NE RACCORDEZ PAS la sécheuse à une - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 37
le couvercle d'accès du bornier dans le coin inférieur du dos de la sécheuse. 3 Installez un réducteur de tension certifié UL conformément aux instructions du fabricant de cordon d'alimentation ou de réducteur de tension dans l'orifice de cordon d'alimentation sous le panneau d'accès. À ce moment, le - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 38
le couvercle d'accès du bornier dans le coin inférieur du dos de la sécheuse. 3 Installez un réducteur de tension certifié UL conformément aux instructions du fabricant de cordon d'alimentation ou de réducteur de tension dans l'orifice de cordon d'alimentation sous le panneau d'accès. À ce moment, le - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 39
à l'utilisation initiale, veuillez vous reporter à la section « Liste de vérification » de votre Guide d'utilisation et d'entretien avant d'effectuer une demande de service. 7 Laissez ces instructions à proximité de la sécheuse pour vous y reporter ultérieurement. Í REMARQUE Un schéma électrique - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 40
INVERSION DE LA PORTE Dépose de la porte 1 Protégez la surface de travail, comme le dessus de la sécheuse ou le plancher près de la sécheuse, avec un chiffon doux ou une serviette. 2 Ouvrez la porte de la sécheuse et retirez les deux vis de la charnière. Enlevez d'abord la vis du bas, puis la vis du - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 41
Inversion de la charnière 1 Enlevez délicatement les 2 petits bouchons circulaires qui se trouvent sur le panneau avant et conservezles. Retirez le protecteur carré de la fente en « T » en le faisant glisser vers le haut et en le tirant vers l'extérieur, puis conservez-le. Ensuite, insérez les 3 - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 42
filet des trous en plastique. nos 1 à 5 nos 6 et 7 2 Déposez l'ouverture de la partie interne de la porte dans un angle de 90 degrés sur les supports de la découpe de la charnière. Ensuite, faites pivoter la partie interne de la porte dans la partie externe. 5 Repérez la nouvelle gâche - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 43
Remise en place de la porte 1 En tenant la porte à deux mains, insérez complètement la tige en « T » située à l'arrière de la charnière dans la fente en « T » se trouvant dans le panneau avant. Ensuite, baissez la porte de sorte que les trous de montage soient alignés. TIGE EN « T » DE LA CHARNIÈRE - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 44
devez commander des pièces de rechange pour votre sécheuse, communiquez avec le marchand qui vous a vendu votre appareil, ou reportez-vous au guide d'utilisation et d'entretien pour obtenir plus de détails. 44 AVERTISSEMENT RISQUE ÉLECTRIQUE Étiquetez tous les fils avant de les débrancher pendant - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 45
Instrucciones de instalación 56-61 Requisitos de instalación 48-54 Inversión de la puerta 62-65 Dimensiones de la secadora instalada 55 Accesorios 66 www.frigidaire.com UEES.AU1U-8.10-08-0904-49-4940-494044 wwwww.fwrig.firdigaidrea.icrea.caCanCaadnaad1á-810-08-0206-52-6853-582352 45 - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 46
aislante resistente al gas LP (para suministro de gas natural o LP) • Nivel de carpintero • Capucha de ventilación externa • Conducto de escape de metal rígido o semirígido de 4 pulgadas (102 mm) • Kit de cables de alimentación trifilar o tetrafilar de 240 voltios (secadora eléctrica) • Abrazadera - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 47
) Válvula de cierre manual instalada en la tubería de suministro Todas las conexiones selladas con un sellante aprobado y bien apretadas con una llave Kit de conversión para el sistema de gas LP Suministro de gas abierto No hay escapes en ninguna conexión: verifique con agua jabonosa, NUNCA - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 48
DE INSTALACIÓN Í NOTA Debido a posibles variaciones en el voltaje, no se recomienda utilizar esta secadora con electricidad generada a partir de generadores a gas, solares, eólicos ni de ninguna otra clase que no sean los empleados por su empresa de electricidad local. Requisitos eléctricos de la - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 49
instalación DEBE realizarse de acuerdo con los códigos locales o, en ausencia de ellos, con el Código de Gas Nacional (National Fuel Gas Code), ANSI Z223.1 (última edición). 2 La línea de suministro de gas debe ser un tubo de 1,27 cm (1/2 pulgada). 3 Si los códigos lo permiten, se puede utilizar un - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 50
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape Utilice solo un conducto de metal flexible o rígido de 102 mm (4 pulgadas) de diámetro (mínimo) y una capucha de ventilación aprobada que tenga uno o más reguladores de tiro que se abran cuando la secadora esté en funcionamiento. Cuando la - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 51
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape (continuación) ADVERTENCIA PELIGRO DE INCENDIO Una secadora de ropa debe tener ventilación al exterior. No ventile la secadora a una chimenea, pared, techo, ático, pasajes entre pisos ni ningún espacio oculto de la vivienda. Las secadoras - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 52
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape (continuación) Instale los accesorios macho en la dirección correcta: Dirección del escape El escape direccional se puede lograr mediante la instalación de un codo de ventilación de giro rápido de 90° directamente en la salida de la - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 53
secciones anteriores de esta guía. 5 Cuando se instale una secadora a gas en una casa rodante, se debe dejar espacio en el exterior para la anclar esta secadora (1) o secadora sobre pedestal (2) al piso usando un kit de instalación para casas rodantes, pieza número 137067200. Requisitos de despeje - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 54
o armario, DEBE tener ventilación al exterior. 2 No se debe instalar ningún otro artefacto de combustión en el mismo armario que la secadora a gas. 3 La secadora necesita espacio a su alrededor para que la ventilación sea adecuada. NO instale la secadora en un armario con puerta maciza. 4 Ventilaci - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 55
5cm) 19.0" (48cm) 71.5" (182cm) conexión del suministro de agua en la parte trasera de la lavadora1 tubería de suministro de gas en la parte trasera de la unidad de gas suministro eléctrico en la parte trasera de la unidad altura de la línea central para ventilación trasera 37" (94cm) manguera - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 56
INSTRUCCIONES DE INSTALACIÓN Instalación eléctrica Los siguientes son requisitos necesarios para la instalación eléctrica segura y correcta de su secadora. El no seguir estas instrucciones puede producir una descarga eléctrica y/o incendio. ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA • Este - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 57
Si no calza en el tomacorrientes, pídale a un electricista calificado que instale un tomacorrientes adecuado. Requisitos de conexión a tierra: secadora a gas (Estados Unidos y Canadá) 1 La secadora está equipada con un enchufe de tres patas (conexión a tierra) para evitar el peligro de electrocuci - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 58
IMPORTANTE NO conecte la secadora al servicio de gas LP sin convertir la válvula de gas. El kit de conversión a gas LP debe ser instalado por un técnico calificado las conexiones de los tubos. FLUJO DE GAS Válvula de cierre manual Conector doble Conector doble Cerrado Conector Abierto Conector - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 59
INSTRUCCIONES DE INSTALACIÓN Conexión eléctrica (fuera de Canadá): trifilar Receptáculo trifilar (tipo NEMA 10-30R) ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA El no desconectar el suministro eléctrico antes de realizar cualquier reparación puede ocasionar lesiones personales o incluso la muerte. 1 - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 60
INSTRUCCIONES DE INSTALACIÓN Conexión eléctrica (fuera de Canadá): tetrafilar Receptáculo tetrafilar (tipo NEMA 14-30R) ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA El no desconectar el suministro eléctrico antes de realizar cualquier reparación puede ocasionar lesiones personales o incluso la muerte. - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 61
INSTRUCCIONES DE INSTALACIÓN Instalación general 1 Conecte el tubo de escape al sistema de escape exterior (consulte las páginas 50 a 54). Se recomienda usar una abrazadera (pieza A) de 4" (10,2 cm) para conectar las secadora al sistema de ventilación de escape. Utilice cinta de papel de aluminio - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 62
INVERSIÓN DE LA PUERTA Cómo extraer la puerta 1 Proteja las superficies de trabajo planas, como la parte superior de la secadora o el piso cerca de ésta utilizando un paño o toalla suave. 2 Abra la puerta de la secadora y retire los dos tornillos de la bisagra. Retire el tornillo inferior primero y - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 63
Inversión de la bisagra 1 Retire cuidadosamente los dos tapones redondos del panel delantero y guárdelos. Retire y guarde la cubierta cuadrada de la ranura en forma de "T" deslizándola hacia arriba y tirando de ella para retirarla. Mueva los 3 tapones al lado opuesto del panel delantero. TAPÓN - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 64
de la cubierta de la bisagra. Gire la puerta interior hacia abajo sobre la puerta exterior. 5 Ubique el nuevo pestillo de metal proporcionado con los manuales de la secadora. Sostenga el pestillo nuevo con alicates como se muestra abajo. Inserte firmemente el pestillo de manera que quede en posici - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 65
Reinstalación de la puerta 1 Mientras sostiene la puerta con ambas manos, introduzca la pieza en forma de "T" que se encuentra en la parte trasera de la bisagra en la ranura en forma de "T" del panel delantero y baje la puerta para alinear los agujeros de instalación. PIEZA EN FORMA DE "T" EN LA - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 66
kit diferente, puede pedir uno. KIT DE CONVERSIÓN A GAS LP Pieza No.. PCK4200 Las secadoras a gas diseñadas para el uso en lugares con suministro de LP requieren utilizar un kit de conversión antes de la instalación. KIT cables antes de desconectarlos. Los errores de cableado pueden producir un - Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 67
- Frigidaire FASG7073LA | Installation Instructions (All Languages) - Page 68
All about the
Installation
of your
Dryer
137336500A (1003)
TABLE OF CONTENTS
Important Safety Instructions
..............................
2-3
Installation Requirements
.................................
4-10
Installed Dryer Dimensions
..................................
11
Installation Instructions
..................................
12-17
Reversing Door
..............................................
18-21
Accessories
.........................................................
22
Français
..............................................................
23
Español
..............................................................
45