Frigidaire FASG7073NA Installation Instructions (All Languages)
Frigidaire FASG7073NA Manual
View all Frigidaire FASG7073NA manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire FASG7073NA manual content summary:
- Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 1
All about the Installation of your Dryer TABLE OF CONTENTS Important Safety Instructions 2-3 Reversing Door 20-23 Installation Requirements 4-10 Accessories 24 Installed Dryer Dimensions 11 Français 25 Installation Instructions 12-19 Español 49 137441900A (1104) - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 2
risk of fire. • The instructions in this manual and all other literature included with this dryer are not meant to cover every possible condition and situation that may occur. Good safe practice and caution MUST be applied when installing, operating and maintaining any appliance. WHAT TO DO IF YOU - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 3
Gas Supply (Gas Dryer) Manual shutoff valve present Dryer) Approved NEMA 10-30R or 14-30R service cord with all screws tight on terminal block Approved strain relief installed Terminal access cover installed before initial operation Door Reversal Follow detailed instructions in this guide - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 4
dryer is internally grounded to neutral unless it was manufactured for sale in Canada. Only a 4-conductor cord shall be used when the appliance closed loop connectors and marked for use with clothes dryers. For 3-wire cord connection instructions see ELECTRICAL CONNECTIONS FOR A 3-WIRE SYSTEM. 4- - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 5
dryer Current. POWER SUPPLY CORD - The dryer is equipped with a 120 volt flexible metal tubing may be used to connect your dryer to the gas supply line. The tubing MUST be connection to the dryer. 6 The dryer MUST be disconnected 1/2 psig (3.45 kPa). 7 The dryer MUST be isolated from the gas supply - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 6
or any other obstruction. WARNING FIRE HAZARD Failure to follow these instructions can create excessive drying times and fire hazards. The following are obstruct clothes dryer airflow and increase the risk of fire. If your present system is made up of plastic duct or metal foil duct, replace it with - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 7
will be expelled into the laundry area. An accumulation of lint in any area of the home can create a health and fire hazard. The dryer must be connected to an exhaust outdoors. Regularly inspect the outdoor exhaust opening and remove any accumulation of lint around the outdoor exhaust opening and - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 8
Exhaust direction Directional exhausting can be accomplished by installing a quick-turn 90° dryer vent elbow directly to exhaust outlet of dryer. Dryer vent elbows are available through your local parts distributor or hardware store. CORRECT INCORRECT In installations where the exhaust system is - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 9
Part 280) or Standard CAN/CSAZ240 MH. 2 Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support to previous sections in this guide for other important exhaust venting system requirements. 5 When installing a gas dryer into a mobile home, a - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 10
or closet, MUST be exhausted outdoors. 2 No other fuel burning appliance shall be installed in the same closet as the gas dryer. 3 Your dryer needs the space around it for proper ventilation. DO NOT install your dryer in a closet with a solid door. 4 Closet door ventilation required: A minimum - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 11
for rear vent 37" (94cm) drain hose on rear of unit3 power cord on rear of unit2 39" (99cm) * To obtain these minimal depth dimensions, dryer must be vented straight back. Using a quick-turn 90° elbow (right) adds approximately 0.75 in. (2 cm) to installation depth. Upward venting of exhaust on - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 12
can create electrical shock and/or a fire hazard. WARNING ELECTRICAL SHOCK HAZARD • This appliance MUST be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. • Do not use an extension cord with this - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 13
INSTALLATION INSTRUCTIONS Grounding requirements - Electric dryer (Canada) WARNING ELECTRICAL SHOCK HAZARD Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 14
INSTRUCTIONS Gas connection 1 Remove the shipping cap from gas pipe at the rear of the dryer. IMPORTANT DO NOT connect the dryer to L.P. gas service be equipped with an approved manual shutoff valve. This valve should be located in the same room as the dryer and should be in a location - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 15
INSTRUCTIONS Water connection (Steam Model only) WATER SUPPLY REQUIREMENTS Cold water faucet MUST be installed within 42 inches (107 cm) of your dryer Remove COLD inlet hose from COLD water supply and inspect for rubber washer. Replace washer if it is torn or worn out. RUBBER WASHER MUST BE PRESENT - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 16
INSTALLATION INSTRUCTIONS Water connection, continued (Steam Model only) 5 If your installation has room for the COLD 90° coupling to the brass water inlet on the back of the dryer and snug it by hand. Tighten each connection of the dryer inlet hose another 2/3 turn with pliers. 10 Turn on the water - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 17
the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel. At this time, the strain relief should - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 18
the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel. At this time, the strain relief should - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 19
. 6 If you have any questions during initial operation, please review the "Avoid Service Checklist" in your Use & Care Guide before calling for service. 7 Place these instructions in a location near the dryer for future reference. Í NOTE A wiring diagram and technical data sheet are located inside - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 20
then upper screw. 4 Gently place dryer door face down on flat, covered work surface. 5 Locate the 5 indented head screws (no. 1-5) in the small, circular recesses (at 11, 1, 4, 6, and 8 o'clock positions) of the inner door. Remove and save these 5 screws. 3 Supporting door with both hands, squarely - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 21
Reversing the hinge 1 Carefully pull out the 2 small round hole plugs from the front panel and save. Remove and save the square "T" slot cover by sliding it up and pulling it out. Move all 3 plugs to the opposite side of the front panel and insert. ROUND PLUG REVERSING DOOR 4 From the back side of - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 22
-hand hinge. 3 Replace indented head screws (no. 1-5) removed earlier. Take care not to strip out the plastic holes. 4 Replace pan head screws (no on the supports for the hinge cutout cover. Pivot the inner door down onto the outer door. 5 Locate new metal strike supplied with dryer manuals. Grip - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 23
holes. "T" POST ON DOOR HINGE "T" SLOT IN FRONT PANEL REVERSING DOOR 3 Close the door and test operation of hinge, strike and latch. 2 While supporting the door, install the upper pan head screw first and then the lower one. Í NOTE Correctly installed hinge screws will press hinge flush to front - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 24
. Replacement parts: If replacements parts are needed for your washer, contact the source where you purchased your washer or refer to your Use and Care Guide for more information. 24 WARNING ELECTRICAL SHOCK HAZARD Label all wires prior to disconnection when servicing controls. Wiring errors can - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 25
Tout à propos de Installation de votre Sécheuse TABLE DES MATIÈRES Mesures de sécurité importantes 26-27 Instructions d'installation 36-43 Exigences d'installation 28-34 Inversion de la porte 44-47 Dimensions, appareil install 35 Accessoires 48 - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 26
installateur qualifié, un technicien de service ou le fournisseur de gaz. • Installez l'appareil conformément aux instructions du fabricant et aux codes et pourraient accroître le risque d'incendie. • Les instructions comprises dans ce guide et toute autre documentation fournie avec cet appareil ne - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 27
certifié est installé Le couvre-borne est installé avant la première mise en marche Inversion de la porte Suivez les instructions détaillées contenues dans ce guide Vérifiez que la charnière et le loquet fonctionnent correctement Alimentation en électricité Le système électrique de la maison - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 28
toute autre source d'alimentation différente de celle fournie par les services publics n'est pas recommandée. Exigences électriques de la sécheuse spécialement indiqués pour une utilisation avec une sécheuse. Pour les instructions de raccordement du cordon à 3 fils, consultez la section CONNEXIONS É - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 29
de gaz à des pressions égales ou inférieures à 3,45 kPa (1/2 lb/po2). 8 Les branchements d'alimentation en gaz doivent être conformes à la norme Connectors for Gas Appliances (Raccords pour appareils au gaz) ANSI Z21.24. 29 - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 30
po) entre le bas de la bouche d'évacuation et le sol ou toute autre obstruction. AVERTISSEMENT RISQUE D'INCENDIE Le non-respect de ces instructions pourrait augmenter démesurément les temps de séchage et entraîner des risques d'incendie. Vous trouverez ci-dessous les exigences pour l'utilisation ad - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 31
EXIGENCES D'INSTALLATION Exigences de système d'évacuation (suite) AVERTISSEMENT RISQUE D'INCENDIE Une sécheuse doit être évacuée vers l'extérieur. N'évacuez pas une sécheuse dans une cheminée, un mur, un plafond, un grenier, un vide sanitaire ou dans tout espace clos d'un bâtiment. La sécheuse - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 32
EXIGENCES D'INSTALLATION Exigences de système d'évacuation (suite) Installez les raccords mâles dans le bon sens : Direction d'évacuation Il est possible de diriger l'évacuation en posant un coude de 90° à courbe immédiate directement à la sortie d'évacuation de la sécheuse. Les coudes pour é - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 33
à l'extérieur de la cloison et être fixé solidement à la structure de la maison. 4 Reportez-vous aux sections précédentes de ce guide relativement aux autres exigences d'évacuation importantes. 5 Lors de l'installation d'une sécheuse à gaz dans une maison mobile, des dispositions doivent être prises - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 34
EXIGENCES D'INSTALLATION Exigences de dégagement (suite) Installation dans un Endroit en Retrait ou une Armoire 1 Une sécheuse installée dans une chambre à coucher, une salle de bains, un renfoncement ou un placard DOIT être évacuée vers l'extérieur. 2 Aucun autre appareil à combustion ne doit ê - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 35
51.4" (131cm) Avec la porte grande ouverte DIMENSIONS DE L'INSTALLATION DE SÉCHEUSE 30.3" (77cm)* À partir de l'avant de la porte lorsqu'elle est fermée 27.0" (68.5cm) 36.0" (91.5cm) 51.25" (130cm) Sécheuse autonome sur le plancher Plancher Alimentation en gaz à l'arrière de l'appareil à gaz - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 36
équatement mis à la terre. La mise à la terre inadéquate de la sécheuse pourrait entraîner des risques de choc électrique. Suivez les instructions de ce guide pour une mise à la terre adéquate. • N'utilisez pas de rallonge avec cet appareil. Certains cordons prolongateurs ne sont pas conçus pour la - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 37
INSTRUCTIONS D'INSTALLATION Exigences de mise à la terre - Sécheuse électrique (Canada) AVERTISSEMENT RISQUE DE CHOC ÉLECTRIQUE Un raccordement inadéquat du conducteur de mise à la terre de l'é - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 38
INSTRUCTIONS D'INSTALLATION Connexion de gaz 1 Retirez le capuchon d'expédition de la conduite de gaz à l'arrière de l'appareil. IMPORTANT NE RACCORDEZ PAS la sécheuse à une - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 39
INSTRUCTIONS D'INSTALLATION Raccordement d'eau (modèles à la vapeur uniquement.) EXIGENCES RELATIVES A L' La pression de l'eau DOIT se situer entre 206,8 et 827,4 kPa (30 et 120 lb/po²). Le service des eaux de votre localité peut vous informer sur la pression de votre alimentation en eau. 1 Fermez l' - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 40
INSTRUCTIONS D'INSTALLATION Raccordement d'eau, suite (modèles à la vapeur uniquement.) 5 Si votre installation offre suffisamment d'espace pour installer directement un raccord en Y à votre tuyau d'arrivée d' - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 41
le couvercle d'accès du bornier dans le coin inférieur du dos de la sécheuse. 3 Installez un réducteur de tension certifié UL conformément aux instructions du fabricant de cordon d'alimentation ou de réducteur de tension dans l'orifice de cordon d'alimentation sous le panneau d'accès. À ce moment, le - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 42
le couvercle d'accès du bornier dans le coin inférieur du dos de la sécheuse. 3 Installez un réducteur de tension certifié UL conformément aux instructions du fabricant de cordon d'alimentation ou de réducteur de tension dans l'orifice de cordon d'alimentation sous le panneau d'accès. À ce moment, le - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 43
à l'utilisation initiale, veuillez vous reporter à la section « Liste de vérification » de votre Guide d'utilisation et d'entretien avant d'effectuer une demande de service. 7 Laissez ces instructions à proximité de la sécheuse pour vous y reporter ultérieurement. Í REMARQUE Un schéma électrique - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 44
INVERSION DE LA PORTE Dépose de la porte 1 Protégez la surface de travail, comme le dessus de la sécheuse ou le plancher près de la sécheuse, avec un chiffon doux ou une serviette. 2 Ouvrez la porte de la sécheuse et retirez les deux vis de la charnière. Enlevez d'abord la vis du bas, puis la vis du - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 45
Inversion de la charnière 1 Enlevez délicatement les 2 petits bouchons circulaires qui se trouvent sur le panneau avant et conservezles. Retirez le protecteur carré de la fente en « T » en le faisant glisser vers le haut et en le tirant vers l'extérieur, puis conservez-le. Ensuite, insérez les 3 - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 46
filet des trous en plastique. nos 1 à 5 nos 6 et 7 2 Déposez l'ouverture de la partie interne de la porte dans un angle de 90 degrés sur les supports de la découpe de la charnière. Ensuite, faites pivoter la partie interne de la porte dans la partie externe. 5 Repérez la nouvelle gâche - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 47
Remise en place de la porte 1 En tenant la porte à deux mains, insérez complètement la tige en « T » située à l'arrière de la charnière dans la fente en « T » se trouvant dans le panneau avant. Ensuite, baissez la porte de sorte que les trous de montage soient alignés. TIGE EN « T » DE LA CHARNIÈRE - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 48
devez commander des pièces de rechange pour votre sécheuse, communiquez avec le marchand qui vous a vendu votre appareil, ou reportez-vous au guide d'utilisation et d'entretien pour obtenir plus de détails. 48 AVERTISSEMENT RISQUE ÉLECTRIQUE Étiquetez tous les fils avant de les débrancher pendant - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 49
Instrucciones de instalación 60-67 Requisitos de instalación 52-58 Inversión de la puerta 68-71 Dimensiones de la secadora instalada 59 Accesorios 72 www.frigidaire.com UEES.AU1U-8.10-08-0904-49-4940-494044 wwwww.fwrig.firdigaidrea.icrea.caCanCaadnaad1á-810-08-0206-52-6853-582352 49 - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 50
á, el CSA C22.1 del Código Eléctrico de Canadá (Canadian Electrical Code) Parte 1. • El servicio de gas de la electrodoméstico debe cumplir con los códigos á, el CAN/CGA B149,1-2000. Se debe instalar una válvula de cierre individual manual a una distancia no mayor a 1,83 m (6 pies) de la secadora de - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 51
instrucciones antes de usar este secadora. Identificación de los símbolos, palabras y avisos de seguridad Las indicaciones de seguridad incluidas en este manual aparecen precedidas de un aviso titulado "ADVERTENCIA" o "PRECAUCIÓN", de acuerdo con el nivel de riesgo. Definiciones Este es el símbolo de - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 52
REQUISITOS DE INSTALACIÓN Í NOTA Debido a posibles variaciones en el voltaje, no se recomienda utilizar esta secadora con electricidad generada a partir de generadores a gas, solares, eólicos ni de ninguna otra clase que no sean los empleados por su empresa de electricidad local. Requisitos elé - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 53
REQUISITOS DE INSTALACIÓN Requisitos eléctricos de la secadora a gas: CIRCUITO - Circuito individual de bifurcación de 15 amp., correctamente polarizado y con conexión a tierra con fusible de retardo de 15 amp. o con interruptor automático. SUMINISTRO ELÉCTRICO: corriente alterna de 2 cables, con - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 54
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape Utilice solo un conducto de metal flexible o rígido de 102 mm (4 pulgadas) de diámetro (mínimo) y una capucha de ventilación aprobada que tenga uno o más reguladores de tiro que se abran cuando la secadora esté en funcionamiento. Cuando la - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 55
de incendio. • No bloquee los extremos de escape del sistema de ventilación, ni utilice tornillos, remaches ni otros sujetadores que se extiendan hacia la parte interna del conducto para ensamblarlo. Es posible que la pelusa quede atrapada en el filtro, los tornillos o los remaches, lo que puede - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 56
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape (continuación) Instale los accesorios macho en la dirección correcta: Dirección del escape El escape direccional se puede lograr mediante la instalación de un codo de ventilación de giro rápido de 90° directamente en la salida de la - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 57
Instalación en una casa rodante 1 La instalación DEBE cumplir con la actual Norma de Seguridad y Construcción de Casas Rodantes, título 24 CFR, Parte 32-80 (que anteriormente se conocía como la Norma Federal de Seguridad y Construcción de Casas Rodantes [Federal Standard for Mobile Home Construction - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 58
ventilación distribuidas uniformemente en toda la superficie. ESPACIOS MÍNIMOS PARA LA INSTALACIÓN: cm (pulgadas) LATERALES PARTE TRASERA PARTE PARTE SUPERIOR DELANTERA Alcôve 0 cm (0") 0 cm (0") 0 cm (0") n/d Sous le comptoir 0 cm (0") 0 cm (0") 0 cm (0") n/d Placard 0 cm (0") 0 cm - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 59
cerrada 16.9" (43cm) 3.75" (9.5cm) 13.50" (34.5cm) hacia el centro de la ventilación trasera 27.0" (68.5cm) suministro eléctrico en la parte trasera de la unidad altura de la línea central para ventilación trasera 3.7" (9.5cm) 19.0" (48cm) 71.5" (182cm) conexión del suministro de agua en la - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 60
INSTRUCCIONES DE INSTALACIÓN Instalación eléctrica Los siguientes son requisitos necesarios para la instalación eléctrica segura y correcta de su secadora. El no seguir estas instrucciones puede producir una descarga eléctrica y/o incendio. ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA • Este - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 61
INSTRUCCIONES DE INSTALACIÓN Requisitos de conexión a tierra: secadora eléctrica (Canadá) ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA Una conexión incorrecta del conductor de conexión a tierra del equipo puede provocar un peligro de descarga eléctrica. Si no está seguro de haber realizado - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 62
gases licuados en todas las conexiones de los tubos. FLUJO DE GAS Válvula de cierre manual Conector doble Conector doble Cerrado Conector Abierto Conector flexible Tubo de admisión en la parte posterior de la secadora Todas las conexiones deben estar ajustadas con llave IMPORTANTE La línea - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 63
INSTRUCCIONES DE INSTALACIÓN Conexión de agua (modelo al vapor solamente) REQUISITOS DE LA ENTRADA DE AGUA Los grifos de agua fría DEBEN instalarse a una distancia no mayor de 107 cm (42 pulgadas) de la entrada de agua de secadora. Los grifos DEBEN estar a 1,9 cm (3/4 pulgadas) con roscas para la - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 64
a la otra salida del conector en "Y" y apriételo a mano. Conecte el codo de 90° de la manguera a la admisión de agua de latón en la parte trasera de la secadora y apriételo a mano. Apriete todas las conexiones de la manguera de admisión de agua de la secadora 2/3 de vuelta más usando alicates - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 65
del tomacorriente. 2 Extraiga el tornillo que sujeta la cubierta de acceso del bloque terminal que se encuentra en la esquina inferior de la parte trasera de la secadora. 3 Instale un dispositivo de liberación de tensión aprobado por U.L., de acuerdo con las instrucciones relativas al cable de - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 66
del tomacorriente. 2 Extraiga el tornillo que sujeta la cubierta de acceso del bloque terminal que se encuentra en la esquina inferior de la parte trasera de la secadora. 3 Instale un dispositivo de liberación de tensión aprobado por U.L., de acuerdo con las instrucciones relativas al cable de - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 67
cuidadosamente. Ajuste una o varias de las patas de la secadora hasta que se encuentre firme sobre las cuatro patas. Coloque un nivel en la parte superior A de la secadora. La secadora DEBE estar nivelada y firme sobre las cuatro patas. Presione las distintas esquinas para asegurarse de que la - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 68
INVERSIÓN DE LA PUERTA Cómo extraer la puerta 1 Proteja las superficies de trabajo planas, como la parte superior de la secadora o el piso cerca de ésta utilizando un paño o toalla suave. 2 Abra la puerta de la secadora y retire los dos tornillos de - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 69
de ella para retirarla. Mueva los 3 tapones al lado opuesto del panel delantero. TAPÓN REDONDO TAPÓN CUADRADO INVERSIÓN DE LA PUERTA 4 Desde la parte trasera de la puerta interior, presione las lengüetas de retención del tapón de plástico cuadrado para liberarlo. Guarde el tapón cuadrado para - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 70
de la cubierta de la bisagra. Gire la puerta interior hacia abajo sobre la puerta exterior. 5 Ubique el nuevo pestillo de metal proporcionado con los manuales de la secadora. Sostenga el pestillo nuevo con alicates como se muestra abajo. Inserte firmemente el pestillo de manera que quede en posici - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 71
Reinstalación de la puerta 1 Mientras sostiene la puerta con ambas manos, introduzca la pieza en forma de "T" que se encuentra en la parte trasera de la bisagra en la ranura en forma de "T" del panel delantero y baje la puerta para alinear los agujeros de instalación. PIEZA EN FORMA - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 72
* Pedestal de color blanco - P/N CFPWD15W Pedestal de color azul - P/N CFPWD15N Pedestal de color rojo - P/N CFPWD15R Pedestal de color plateada - P/N CFPWD15A Pedestal de color negra - P/N CFPWD15B Un accesorio de pedestal de almacenamiento, especialmente diseñado para esta secadora, se puede - Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 73
- Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 74
- Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 75
- Frigidaire FASG7073NA | Installation Instructions (All Languages) - Page 76
All about the
Installation
of your
Dryer
137441900A (1104)
TABLE OF CONTENTS
Important Safety Instructions
..............................
2-3
Installation Requirements
.................................
4-10
Installed Dryer Dimensions
..................................
11
Installation Instructions
..................................
12-19
Reversing Door
..............................................
20-23
Accessories
.........................................................
24
Français
..............................................................
25
Español
..............................................................
49