Frigidaire FFRS1022R1 Installation Instructions

Frigidaire FFRS1022R1 Manual

Get Frigidaire FFRS1022R1 PDF manuals and user guides View all Frigidaire FFRS1022R1 manuals
Add to My Manuals
Save this manual to your list of manuals

Frigidaire FFRS1022R1 manual content summary:

  • Frigidaire FFRS1022R1 | Installation Instructions - Page 1
    Instructions READ BEFORE INSTALLING UNIT For Slider Casement Air Conditioners INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step as shown. be exposed: Carefully inspect location where air conditioner will be installed. Be sure it will support
  • Frigidaire FFRS1022R1 | Installation Instructions - Page 2
    lifting techniques. Inspect the condition of the window where unit will be installed. Be sure it will support the weight of the unit. This appliance must be installed according to all applicable codes and ordinances. Handle air conditioner with care. AVOID sharp metal fins on front and rear coils
  • Frigidaire FFRS1022R1 | Installation Instructions - Page 3
    Installation Instructions 1 Make sure you have all the necessary parts. Installation kit contents (FIG.3): No. Hardware 1 Platform 2 Support brace 3 Adjustment bolt 4 Hex flange nut - 1/4 5 Track seal 6 Side channel seal 7 Window sash seal 8 Safety bracket 9 10 Qty. No. Hardware 1
  • Frigidaire FFRS1022R1 | Installation Instructions - Page 4
    install the platform. Follow the instructions below to do that. 1. Place the support bracket on the window sill as shown (FIG.8C). Using the holes in the support bracket as a guide attach a siding-protection board to side of house (FIG.10). NOTE: Siding-protection board should be long enough to span
  • Frigidaire FFRS1022R1 | Installation Instructions - Page 5
    it to support bracket as shown (FIG.11B). tab against 10 Adjust platform assemblyVRWKDWRXWVLGHHGJHLVƎORZHUWKDQ inside of track. inside edge, as shown (FIG.11A & FIG.B). This ensures proper water drainage 2XWVLGHHGJHLVƎ lower than inside. from the air conditioner. 11 Level
  • Frigidaire FFRS1022R1 | Installation Instructions - Page 6
    Installation Instructions 19 Slide inner window sash firmly against side of the and window clearance problems, the unit can be installed in a stationary sash section. However, the horizontal mullion and WKHJODVVSDQHOVPXVWEHUHPRYHGEHIRUHLQVWDOODWLRQ 24 Attach support brace to platform
  • Frigidaire FFRS1022R1 | Installation Instructions - Page 7
    Installation Instructions NOTE: If you are planning to use a siding-protection outside). After proper installation, condensate should not drain from the overflow drain hole during normal use, correct the slope otherwise. NOTE: A projection below the base of the air conditioner will require the
  • Frigidaire FFRS1022R1 | Installation Instructions - Page 8
    Installation Instructions 34 Cut side channel seal into 2 equal lengths. Remove the the case. 4. Then release the electrical coupler plug. NOTE: DO NOT push or pull air direction louvers. 36 Place the air conditioner in the window opening as shown (FIG.31). It should sit on the platform assembly so
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
READ BEFORE INSTALLING UNIT
For Slider Casement Air Conditioners
1
Installation Instructions
NOTE:
These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or
installation in a metal CASEMENT window. Modification may be necessary when installing in windows made
differently than those shown in these instructions.
WARNING:
Electrical ground is required on this appliance.
DO NOT ground to a gas line.
If cold water pipe is interrupted by plastic, non-metallic gaskets, or other insulating materials, DO NOT use for
grounding.
Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded.
DO NOT modify power supply cord plug. If it does not fit outlet, have a proper outlet installed by a qualified
electrician.
DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral, or grounding circuit could result in
an electrical shock.
DO NOT use an extension cord with this appliance.
Meeting Electrical Requirements
OBSERVE ALL LOCAL GOVERNING CODES AND ORDINANCES. DO NOT, UNDER ANY CIRCUMSTANCES,
NOTE:
If codes permit, and a separate grounding wire is used, it is recommended that a qualified electrician determine
that the grounding path is adequate and not interrupted by plastic, non-metallic gaskets, or other insulating
materials.
be exposed:
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended
period of time.
Make sure air conditioner does not fall during installation.
Carefully read the installation manual before beginning.
Follow each step as shown.
INSTALLATION WARNINGS AND CAUTION