Frigidaire FFTA103WA1 Installation Instructions
Frigidaire FFTA103WA1 Manual
 |
View all Frigidaire FFTA103WA1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire FFTA103WA1 manual content summary:
- Frigidaire FFTA103WA1 | Installation Instructions - Page 1
Instructions READ BEFORE INSTALLING UNIT For Through-the-Wall Air Conditioners INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over an extended period of time. Handle - Frigidaire FFTA103WA1 | Installation Instructions - Page 2
Installation Instructions Common Wall-Sleeve Dimensions 1. Identify the wall-sleeve brand for your that serves as a stop for the air conditioner. For new or replacement installations, a Frigidaire Sleeve Kit (5304514430) is recommended. NOTE: When installation is complete, replacement unit must - Frigidaire FFTA103WA1 | Installation Instructions - Page 3
two rear intakes. It is very important that these installation instructions are followed so your unit can operate at maximum efficiency. with the one shipped with the unit in the accessory kit. Existing Frigidaire sleeves may have older single sided intake grilles • These grilles should be - Frigidaire FFTA103WA1 | Installation Instructions - Page 4
Installation Instructions Grille Removal Important: Single intake grilles must be removed when used with dual intake Through-the-wall Units. Warning: When removing grilles, protect from falling - Frigidaire FFTA103WA1 | Installation Instructions - Page 5
the grille) Unit Mounted Grilles In some cases it may be possible to remove a non-Frigidaire grille and attach the dual intake grille directly to the unit as shown below. Instructions for direct attachment are shown on the page titled "Direct Unit Mounting" Directional Grilles When installing - Frigidaire FFTA103WA1 | Installation Instructions - Page 6
Installation Instructions Direct Unit Mounting In cases where the dual intake grille cannot be mounted directly to the sleeve it is desirable to attach the grille to - Frigidaire FFTA103WA1 | Installation Instructions - Page 7
. 7. Gently slide unit into sleeve. 5 4 Ground Wire Installation 1. Install screw end of ground wire into inside of sleeve according to preparation instructions. 2. Before sliding unit all the way back remove second screw from left side of unit. 3. Remove plastic washer from screw. 4. Screw the - Frigidaire FFTA103WA1 | Installation Instructions - Page 8
Installation Instructions Non-Frigidaire Dual Intake Grille In cases where the existing sleeve is a non-Frigidaire sleeve but is installed with a dual intake grille. The existing grille may be left in place. Make sure the outer 3 ½" to 4 ½" louvers are angled from - Frigidaire FFTA103WA1 | Installation Instructions - Page 9
Subsitute Grille Installation Instructions Important: Single intake grilles must be removed when used with used with dual intake Through-the-wall Units. Installation of a standard size Through-the-Wall - Frigidaire FFTA103WA1 | Installation Instructions - Page 10
Trim Kit Installation Instructions 1. Install the 1" x 1" x 84" long stuffer seal between the wall sleeve and the unit. A flat-bladed screwdriver or putty knife is recommended. 2. Assemble the trim frame
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
 |
 |
Hardware
2
2
3
Tapered Spacer (17” Long)
4
4
1
2
3
4
5
1
6
2
3
7
8
.
y
t
Q
.
o
N
2
9
Centering/Support Blocks (
”
)
4
”
x 3
”
x 1
1
2
1
2
1
2
Plastic Divider (
)
1/8
”
x 4
”
x 14
”
1
2
1
2
Stuffer Seal (
)
1
”
x 1
”
x 84
”
1
2
Seal (
)
1
”
x 1
”
x 25
”
1
2
Seal (
)
1
”
x 1
”
x 14
”
1
2
Seal (
)
1
”
x 3/8
”
x 25
”
Seal(
)
1
”
x 3/8
”
x 14
”
Seal (
)
1
”
x 3/4
”
x 14
”
2
Hardware
2
1
1
Ground Wire (green)
2
13
10
11
12
14
Grounding Screw
1
5
1
1
6
1
17
.
y
t
Q
.
o
N
4
18
Trim Frame (top & bottom legs)
Grille (plastic)
Grille Aluminum
Nuts (plastic)
Screw w/washer
4
Trim Frame (side legs)
Tooth washer for grounding screw
2
READ BEFORE INSTALLING UNIT
For Through-the-Wall Air Conditioners
1
Installation Instructions
NOTE:
DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED HERE
Note that the air conditioner dimensions are: 24" wide,14" high, and 19" deep (without front). Install air conditioner
according to these installation instructions to achieve the best performance. Save these installation instructions for
future reference.
Do This First (for existing sleeve)
You may not need all parts in the kit. Discard unused parts.
Items in Kit
16120300A19315
INSTALLATION WARNINGS AND CAUTION
Carefully read the installation manual before beginning. Follow each step as shown.
Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.
Pay attention to danger and safety notices.
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that
may be exposed.
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and
install the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils.
To prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over an extended
period of time.
Handle air conditioner with care.
Make sure air conditioner does not fall during installation.