Frigidaire FGEF3058RB Wiring Diagram

SERVICE DATA SHEET

Electric Range with ES 540 Electronic Oven Control

NOTICE - This service data sheet is intended for use by persons having

electrical and mechanical training and a level of knowledge of these

subjects generally considered acceptable in the appliance repair trade.

The manufacturer cannot be responsible, nor assume any liability for

injury or damage of any kind arising from the use of this data sheet.

SAFE SERVICING PRACTICES

To avoid the possibility of personal injury and/or property damage, it is important

that safe servicing practices be observed.

The following are examples, but

without limitation, of such practices.

1.

Before servicing or moving an appliance remove power cord from electrical

outlet, trip circuit breaker to OFF, or remove fuse.

2.

Never interfere with the proper installation of any safety device.

3.

GROUNDING:

The standard color coding for safety ground wires is

GREEN

or

GREEN WITH YELLOW STRIPES

.

Ground leads are not to be

used as current carrying conductors.

It is extremely important that the

service technician reestablish all safety grounds prior to completion

of service.

Failure to do so will create a potential safety hazard.

4.

Prior to returning the product to service, ensure that:

• All electric connections are correct and secure.

• All electrical leads are properly dressed and secured away from sharp

edges, high-temperature components, and moving parts.

• All uninsulated electrical terminals, connectors, heaters, etc. are adequately

spaced away from all metal parts and panels.

• All safety grounds (both internal and external) are correctly and securely

reassembled.

Oven Calibration

Set the electronic oven control for normal baking at 350°F.

Obtain an average

oven temperature after a minimum of 5 cycles.

Press

cancel

keypad to end

bake mode.

Temperature Adjustment

1.

While in a non-cooking mode, press and hold the

bake

keypad for 6

seconds.

2.

The current calibration offset (temperature adjustment) should appear in

the temperature display.

3.

Use the number keypads (0-9) to enter the desired amount of adjustment

(up to 35°F).

4.

Press the

self-clean

keypad to change the sign of the adjustment to a (-) if

necessary. A positive adjustment will not display a sign.

5.

Once the desired adjustment (-35° to 35° F) has been entered, press the

start

keypad to accept the change or the

cancel

keypad to reject the

change.

Note:

Changing calibration affects all baking modes. The adjustments made will

not change the self-cleaning temperature.

ELECTRONIC OVEN CONTROL (EOC) FAULT CODE DESCRIPTIONS

Fault

Code

Likely Failure/Cause

Suggested Corrective Action

F10

Runaway Temperature.

Oven heats when no cook cycle

is programmed.

If Oven is cold:

1.

If fault code is present with cold oven test oven temperature sensor probe circuit resistance. Use RTD scale

found in the tech sheet.

2.

Replace probe or repair wiring connections if defective.

3.

If temperature sensor probe circuit is good but fault code remains when oven is cold replace the EOC.

If Oven is overheating:

1.

If oven is severely overheating/heating when no cook cycle is programmed test oven temperature sensor

probe circuit resistance using the RTD scale found in the service tech sheet. Also verify that the temperature

sensor probe in properly installed in the oven cavity.

2.

Disconnect power from the range, wait 30 seconds and reapply power. If oven continues to heat when the

power is reapplied, replace the EOC.

NOTE:

Severe overheating may require the entire oven to be replaced

should damage be extensive.

F11

Shorted keypad or Selector

Switch.

1. Reset power supply to range - Disconnect power, wait 30 seconds and reapply power.

2. Check/reseat ribbon harness connections.

3. Replace the EOC.

F12

EOC internal software error or

failure

(some models).

Disconnect power, wait 30 seconds and reapply power. If fault returns upon power-up, replace EOC.

F13

F15

EOC internal hardware error or

failure

(some models).


F16

EOC internal software error or

failure

(some models).


F17

F18

F30

Open oven sensor probe circuit.

Check resistance at room temperature & compare to RTD Sensor resistance chart. If resistance is correct replace

the EOC. If resistance does not match the RTD chart replace RTD Sensor Probe. Check Sensor wiring harness

between EOC & Sensor Probe connector.

F31

Shorted oven sensor probe

circuit.

Check resistance at room temperature, if less than 500 ohms, replace RTD Sensor Probe. Check for shorted

Sensor Probe harness between EOC & Probe connector. If resistance is correct replace the EOC.

F60

Electronic Oven Control (EOC)

over temperature.

Higher than normal temperature

detected on the EOC circuit

board.

1. Verify proper assembly of backguard panel. Check for damaged or loose panels, brackets, endcaps, etc.

2. Check for blocked ventilation slots in control panel rear cover.

3.

Inspect oven vent for proper assembly and air ﬂow.

4. Verify operation of cooling fan (if present).

F90

Door lock motor or latch circuit

failure.

If lock motor runs:

1.

Test continuity of wiring between EOC and lock switch on lock motor assy. Repair if needed.

2.

Advance motor until cam depresses the plunger on lock motor switch. Test continuity of switch contacts. If

switch is open replace lock motor assy.

3.

If motor runs and switch contacts and wiring harness test good, replace the EOC.

If lock motor does not run:

1.

Test continuity of lock motor windings. Replace lock motor assembly if windings are open.

2.

Test lock motor operation by using a test cord to apply voltage. If motor does not operate replace lock motor

assy.

3.

If motor runs with test cord check continuity of wire harness to lock motor terminals. If harness is good

replace the EOC.

F91

F92

F93

F94

F95

Line

ERR

EOC Internal voltage test error or

failure.


CIRCUIT

ANALYSIS MATRIX

EOC Relays

Door

Switch

COM-NO

Warmer

Drawer

MDL

(some models)

L1 to

Bake

L1 to

Broil

L1 to

MDL

L1 to Conv/

Speed Bake

Fan

(some models)

Bake/Time Bake

X

X*

X

Conv/Speed Bake

X

X*

X

X

Broil

X*

X

Clean

X

Unlocked

Locking

X

Locked

Unlocking

X

Door Open

Door Closed

X

Cooktop Active

Note: X=Check listed circuits

* = Alternates with bake element

IMPORTANT

DO NOT REMOVE THIS BAG

OR DESTROY THE CONTENTS

WIRING DIAGRAMS AND SERVICE

INFORMATION

ENCLOSED

REPLACE CONTENTS IN BAG

Resistance (ohms)

1000 ± 4.0

1091 ± 5.3

1453 ± 8.9

1654 ± 10.8

1852 ± 13.5

2047 ± 15.8

2237 ± 18.5

2697 ± 24.4

Open circuit/infinite resistance

RTD SCALE

Temperature °F (°C)

32 ± 1.9 (0 ± 1.0)

75 ± 2.5 (24 ± 1.3)

250 ± 4.4 (121 ± 2.4)

350 ± 5.4 (177 ± 3.0)

450 ± 6.9 (232 ± 3.8)

550 ± 8.2 (288 ± 4.5)

650 ± 9.6 (343 ± 5.3)

900 ± 13.6 (482 ±7.5)

Probe circuit to case ground

Resistance Temperature Detector

316905242 REV B (1503)

Electronic Oven Control

& jumper connections (EOC rear view)

CONVECTION ELEMENT (some models)

OVEN LIGHT (some models)

MOTOR DOOR LATCH (some models)

CONVECTION FAN (some models)

L1

N

J3

P12

P11

P8

MEAT PROBE

(some models)

MEAT PROBE

(some models)

TEMP PROBE

TEMP PROBE

EXTERNAL SWITCH RETURN

DOOR SWITCH

(some models)

MOTOR DOOR LATCH SWITCH

WARMER ZONE

(some models)

WARMER ZONE

(some models)

P7

P9

BAKE

BROIL

P5

L1

P3

L2 IN

L2 OUT

P1

L2 OUT

L2 IN

Frigidaire FGEF3058RB Wiring Diagram

Frigidaire FGEF3058RB Manual

Frigidaire FGEF3058RB manual content summary: