Frigidaire FPFU19F8WF Wiring Diagram

Frigidaire FPFU19F8WF Manual

Get Frigidaire FPFU19F8WF PDF manuals and user guides View all Frigidaire FPFU19F8WF manuals
Add to My Manuals
Save this manual to your list of manuals

Frigidaire FPFU19F8WF manual content summary:

  • 1
  • 2
SERVICE DATA SHEET
A16331304
AUTOMATIC DEFROST
UPRIGHT FREEZER - R600A
DEFROST CONTROL
The defrost period will vary dependent on the heater on time, with a maxi-
mum of 60 minutes. There is a 5 minute idle (drip time) time after the heater
turns off before the evaporator fan and compressor will turn on. During the
defrosting period a temperature sensor monitors the evaporator temperature
and the main control board turns the defrost heater off after the frost on the
evaporator has melted.
A manual defrost can be activated by simultaneously pressing and holding
+
and
AIR FILTER
for 10 seconds. The temperature display will show
dF
for a
few seconds indicating manual defrost is activated and a beep will be heard.
Then the unit will display the last set point. There may be up to a 3 minute
delay before the defrost heater is energized.
Specifications subject to change without notice. For complete performance
data by model, refer to service manual. Options shown are not necessarily
part of model.
PERFORMANCE AT FACTORY SETTING
Ambient Temperature
70°F
90°F
Operating Time
100%
Freezer Temperature
4 to -4°F
Low Side Pressure (Cut-in)
——
Low Side Pressure (Cut-off)
-9.8 to -4.4 psig
-7.8 to -4.4 psig
High Side Pressure
35 to 47 psig
51 to 56 psig
Wattage
35W
54W
Amps
0.50
0.68
Base Voltage
115
Refrigerant Charge
50g
Defrost Heater
206W
IMPORTANT SAFETY NOTE
The information provided herein is designed to assist qualified repair
personnel only. Untrained persons should not attempt to make repairs due to
the possibility of electrical shock. Disconnect power cord before servicing this
appliance.
IMPORTANT
If any green/yellow grounding wires are removed during servicing, they
must be returned to their original position and properly secured.
SERVICE MODE DIAGNOSTIC TESTS
Allows technicians to step through available tests to diagnose individual
electrical circuits.
To Enter and Exit Service Mode:
Press and hold
—
and
+
simultaneously for 10 secs
Controls:
Upon entering Service Mode the User Interface illumination test begins.
1.
All of the LEDs on the User Interface will illuminate.
2. Press and release
+
and all of the LEDs on the User Interface will turn off.
3. Press and release
+
to move to the Output Loads test. Press and release
FREEZE BOOST
to energize load.
4.
Pressing and releasing + moves through the Output Loads test, input
tests and information display phase. Press and release
—
to go back to
previous tests.
5.
The table provides the test description, test number that is displayed to
identify the specific test being performed and the displayed info when
the test output or input is activated.
IMPORTANT: PLEASE RETURN THIS SHEET TO
ITS ORIGINAL LOCATION.
DEFROST SPECIFICATIONS
Cabinet Size: 19´
Thermal Cutout
Heater
Open
Closed
Watts
Ohms
n/a
206
n/a
ICE MAKER INFORMATION
Adjust Water Fill Setting:
Press and hold
FREEZER BOOST
and
ICE MAKER
together for 10 seconds. Use
+
and
—
to select water fill setting.
Display switches back to normal mode in 10 seconds.
120 VAC OUTPUT LOAD TESTS
Test Number
Load
Display
Defrost Heater
2
120 VAC,
≈206 W
oF (OFF)/
on (ON)
Condenser Fan
12
120 VAC,
≈3.1 W
Primary Water Valve
82
120 VAC,
≈15 W
DIGITAL OUTPUT TESTS
Test Number
Load
Display
DC Evaporator Fan
15
+12 VDC,
≈
1 W
oF (OFF)
Ո
I (MID SPEED)
on (FULL SPEED)
Freezer LED Lights
20
+12 VDC,
≈
21.6 W Total
oF (OFF)/
on (ON)
Compressor Invert-
er Speed Control
38
12 V Square Wave
Ice Maker Fan
62
+12 VDC,
≈
2.5 W
Ice Maker Filtered
Water Fill Output
81
+12 VDC
Fill Tube Heater
94
+12 VDC,
≈
0.9 W
TWIST TRAY ICE MAKER TESTS
This phase is to test the ice maker twist tray motor and bail arm. When this mode
is entered the twist tray motor moves to the home position. Pressing and releasing
FREEZE BOOST
makes the twist tray cycle (flashes
I
while cycling). Pressing and
releasing
FREEZE BOOST
again makes the bail arm cycle, checking if the ice bucket
is empty or full.
Test Number
Display
Twist Tray Motor
88
GO (HOME)/I (FLASHING)/
GO (CYCLE COMPLETED)
Bail Arm
86
E
Ո (EMPTY)/ I (FLASHING)/
E
Ո (EMPTY)
or
FU (FULL)
DIGITAL INPUT TESTS
Test Number
Display
Freezer Magnetic
Door Switch
24
OP (OPEN)/CL (CLOSED)
TEMPERATURE SENSOR TESTS
Test Number
Display
Freezer Cabinet
Temp Sensor
30
OP (OPEN)/SH (SHORT)
Main Board Ambient
Temp Sensor
33
Evaporator Defrost
Temp Sensor
39
Ice Maker Twist
Tray Temp Sensor
87
Software Code Streaming
During this phase all software parameters and codes which are programmed
into the Main Control Board and User Interface board will be displayed in the
following order:
1.
Main Control Board parameters code (8 characters)
2.
Main Control Board software name code (8 characters)
3.
User Interface software name code (8 characters)
The User Interface displays each character for 1 second, and then the buzzer
emits a short beep and displays the next character.
•
Between the 3 different sets of code displays, the User Interface displays a
horizontal bar.
•
Pressing and releasing
+
before the software streaming phase is completed
the Service Mode goes straight to the lifetime information display phase.
•
After the software code streaming phase is complete the test automatically
goes to the lifetime streaming phase.
Lifetime Display
During this phase the display shows the total number of days the appliance has
been powered up.
•
Each number is shown on the display starting from the most significant
one. Pressing and releasing
+
makes the buzzer emit a short beep and then
display the next digit.
•
Pressing and releasing
+
when the fourth digit is displayed makes the
Service Mode go straight to the final phase.
Final Phase
During this phase the User Interface shows a 1-sec upcounting timer.
This phase communicates Service Mode has come to an end. To return to
normal mode, press and hold
—
and
+
simultaneously for 10 secs.
ERROR CODES
Error Type
Digit Display
Communication error (communication
was never achieved at power up or lost
communication between main board and
UI board during normal system run)
CE
Freezer Cabinet NTC
T1
Freezer Defrost NTC
T2
Freezer Ice Maker NTC
T8