Frigidaire FPIF3093LF Wiring Diagram (All Languages)

NOTICE - This service data sheet is intended for use by persons having electrical and mechanical training and a level of knowledge of these

subjects generally considered acceptable in the appliance repair trade.

The manufacturer cannot be responsible, nor assume any liability

for injury or damage of any kind arising from the use of this data sheet.

SAFE SERVICING PRACTICES

To avoid the possibility of personal injury and/or property damage, it is important that safe servicing practices be observed. The following are

examples, but without limitation, of such practices.

1.

Before servicing or moving an appliance remove power cord from electrical outlet, trip circuit breaker to OFF, or remove fuse.

2.

Never interfere with the proper installation of any safety device.

3.

GROUNDING:

The standard color coding for safety ground wires is

GREEN

or

GREEN WITH YELLOW STRIPES

.

Ground leads are not to

be used as current carrying conductors.

It is extremely important that the service technician reestablish all safety grounds prior to

completion of service.

Failure to do so will create a potential safety hazard.

4.

Prior to returning the product to service, ensure that:

• All electric connections are correct and secure.

• All electrical leads are properly dressed and secured away from sharp edges, high-temperature components, and moving parts.

• All uninsulated electrical terminals, connectors, heaters, etc. are adequately spaced away from all metal parts and panels.

• All safety grounds (both internal and external) are correctly and securely reassembled.

Oven Calibration

Set the electronic oven control for normal baking at 350°F.

Obtain an average oven temperature after a minimum of 5 cycles.

Press

Stop

keypad

to end Bake mode.

Temperature Adjustment

1.

While in a non-cooking mode, press and hold the

Bake

key pad for 6 seconds.

2.

The current calibration offset (temperature adjustment) should appear in the temperature display.

3.

Use the number key pads (0-9) to enter the desired amount of adjustment (up to 35°F).

4.

Press the

Self Clean

keypad to change the sign of the adjustment to a (-) if necessary. A positive adjustment will not display a sign.

5.

Once the desired adjustment (-35° to 35° F) has been entered, press the

Start

keypad to accept the change or the

Cancel

keypad to reject

the change.

Note:

Changing calibration affects all Baking modes. The adjustments made will not change the self-cleaning temperature.

RTD SCALE

Temperature (°F)

Resistance (ohms)

32 ± 1.9

1000 ± 4.0

75 ± 2.5

1091 ± 5.3

250 ± 4.4

1453 ± 8.9

350 ± 5.4

1654 ± 10.8

450 ± 6.9

1852 ± 13.5

550 ± 8.2

2047 ± 15.8

650 ± 9.6

2237 ± 18.5

900 ± 13.6

2697 ± 24.4

SERVICE DATA SHEET

Electric

Range with ES 540 Electronic Oven Control

p/n

316904436 (1007)

Resistance

Temperature

Detector (RTD)

Resistance Temperature Detector Scale

Circuit

Analysis Matrix

IMPORTANT

DO NO

T REMO

VE

THIS B

A

G

OR DESTR

O

Y

THE CONTENTS

WIRING DIAGRAMS AND SERVICE

INFORMATION

ENCLOSED

REPLACE CONTENTS IN BAG

Electronic Oven Control Fault Code Descriptions

Fault

Code

Runaway temperature.

Oven heats when no cook

cycle is programmed.

Likely failure

condition/cause

Suggested Corrective Action

Shorted keypad or selector

switch.

F11

1. Reset power supply to range - Disconnect power, wait 30 seconds and reapply power.

2. Check/reseat ribbon harness connections between touch panel and EOC.

3. Test keyboard circuits. Replace touch panel if defective.

4. If keyboard ciruits check good replace the EOC.

EOC Internal software error

or failure.

F12

F13

Disconnect power, wait 30 seconds and reapply power. If fault returns upon power-up, replace EOC.

Open oven sensor probe

circuit.

Shorted oven sensor probe

circuit.

F30

1. (F30) Check resistance at room temperature & compare to RTD Sensor resistance chart. If resistance is correct replace the EOC. If

resistance does not match the RTD chart replace RTD Sensor Probe. Check Sensor wiring harness between EOC & Sensor Probe

connector.

2. (F31) Check resistance at room temperature, if less than 500 ohms, replace RTD Sensor Probe. Check for shorted Sensor Probe

harness between EOC & Probe connector. If resistance is correct replace the EOC.

F31

F90

F91

F92

F93

F94

F95

If lock motor runs:

1. Test continuity of wiring between EOC and lock switch on lock motor assy. Repair if needed.

2. Advance motor until cam depresses the plunger on lock motor switch. Test continuity of switch contacts. If switch is open replace

lock motor assemblyy.

3. If motor runs and switch contacts and wiring harness test good, replace the EOC.

If lock motor does not run:

1. Test continuity of lock motor windings. Replace lock motor assembly if windings are open.

2. Test lock motor operation by using a test cord to apply voltage. If motor does not operate replace lock motor assy.

3. If motor runs with test cord check continuity of wire harness to lock motor terminals. If harness is good replace the EOC.

Door lock motor or latch

circuit failure.

If Oven is cold:

1. If fault code is present with cold oven test oven temperature sensor probe circuit resistance. Use RTD scale found in the tech sheet.

2. Replace probe or repair wiring connections if defective.

3. If temperature sensor probe circuit is good but fault code remains when oven is cold replace the EOC.

If Oven is overheating:

1. If oven is severely overheating/heating when no cook cycle is programmed test oven temperature sensor probe circuit resistance using

the RTD scale found in the service tech sheet. Also verify that the temperature sensor probe in properly installed in the oven cavity.

2. Disconnect power from the range, wait 30 seconds and reapply power. If oven continues to heat when the power is reapplied, replace

the EOC.

NOTE:

Severe overheating may require the entire oven to be replaced should damage be extensive.

F10

Communication failure

between EOC & ESEC

system

1. Test harness/connections between P6 (EOC) and P7 (UIB).

2. If harness checks O.K., failure can be caused by faulty UIB or EOC

F20

1. Check/reseat connections between membrane switch, display boards and EOC.

2. Replace the membrane control panel assembly.

3. Replace the EOC.

Electronic Oven Control

& Jumper Connections (EOC Rear View)

Membrane switch tail missing

or not connected

F14

Frigidaire FPIF3093LF Wiring Diagram (All Languages)

Frigidaire FPIF3093LF Manual

Frigidaire FPIF3093LF manual content summary: