Fujitsu MHU2100AT Manual/User Guide
Fujitsu MHU2100AT - Mobile 100 GB Hard Drive Manual
 |
UPC - 000052622700
View all Fujitsu MHU2100AT manuals
Add to My Manuals
Save this manual to your list of manuals |
Fujitsu MHU2100AT manual content summary:
- Fujitsu MHU2100AT | Manual/User Guide - Page 1
Dimensions 3.2 Mounting 3.3 Cable Connections 3.4 Jumper Settings This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. For information about handling this hard disk drive and the system - Fujitsu MHU2100AT | Manual/User Guide - Page 2
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the disk drive and positions of the mounting screw holes. All dimensions are in mm. Figure 3.1 Dimensions 3-2 C141-E202-01EN - Fujitsu MHU2100AT | Manual/User Guide - Page 3
Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation Figure 3.2 illustrates the allowable orientations for the disk drive. gravity (a) Horizontal -1 (b) Horizontal -1 (c) Vertical -1 gravity (d) Vertical -2 gravity - Fujitsu MHU2100AT | Manual/User Guide - Page 4
Installation Conditions (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero. The mounting frame is connected to SG. IMPORTANT Use M3 screw for the mounting screw and the screw length should satisfy the specification in Figure 3.3. The tightening torque must be 0.49N•m (5kgf•cm). - Fujitsu MHU2100AT | Manual/User Guide - Page 5
3.2 Mounting IMPORTANT Because of breather hole mounted to the HDD, do not allow this to close during mounting. Locating of breather hole is shown as Figure 3.4. For breather hole of Figure 3.4, at least, do not allow its around φ 2.4 to block. Figure 3.4 Location of breather C141-E202-01EN 3-5 - Fujitsu MHU2100AT | Manual/User Guide - Page 6
Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to the ambient temperature at a point 3 cm from the disk drive. The ambient temperature must satisfy the temperature conditions described in Section 1.4, and the airflow must be - Fujitsu MHU2100AT | Manual/User Guide - Page 7
affected by external magnetic fields. Damage: Do not press the cover of the disk drive. Pressing it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Static: When handling the device, disconnect the body ground (500 kΩ or greater). Do not touch the printed - Fujitsu MHU2100AT | Manual/User Guide - Page 8
is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of the screw strictly. M3 0.49N·m (5 kgf·cm). - Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200-3056-8 SKY-8A (Color Seiden Mat) SS-6500 Maker SUMITOMO - Fujitsu MHU2100AT | Manual/User Guide - Page 9
3.3 Cable Connections 3.3 Cable Connections 3.3.1 Device connector The disk drive has the connectors and terminals listed below for connecting external devices. Figure 3.8 shows the locations of these connectors and terminals. Connector, PCA setting pins Figure 3.8 Connector locations C141- - Fujitsu MHU2100AT | Manual/User Guide - Page 10
specifications for the cable connectors. Table 3.2 Cable connector specifications ATA interface and power supply cable (44-pin type) Name Cable socket (44-pin type) Model 89361-144 Manufacturer FCI IMPORTANT For the host interface cable, use a ribbon cable. A twisted cable or a cable - Fujitsu MHU2100AT | Manual/User Guide - Page 11
3.4 Jumper Settings 3.3.4 Power supply connector (CN1) Figure 3.10 shows the pin assignment of the power supply connector (CN1). Figure 3.10 Power supply connector pins (CN1) 3.4 Jumper Settings 3.4.1 Location of setting jumpers Figure 3.11 shows the location of the jumpers to select drive - Fujitsu MHU2100AT | Manual/User Guide - Page 12
3.12 Factory default setting 3.4.3 Master drive-slave drive setting Master drive (disk drive #0) or slave drive (disk drive #1) is selected. Open 1 CA 2 DB Open (a) Master drive 1 CA Open Short 2 DB (b) Slave drive Figure 3.13 Jumper setting of master or slave drive Note: Pins A and - Fujitsu MHU2100AT | Manual/User Guide - Page 13
(CSEL) setting. 3.4 Jumper Settings Open 1 CA 2 DB Short Note: The CSEL setting is not depended on setting between pins Band D. Figure 3.14 CSEL setting Figure 3.15 and 3.16 show examples of cable selection using unique interface cables. By connecting the CSEL of the master drive to the - Fujitsu MHU2100AT | Manual/User Guide - Page 14
Installation Conditions drive drive Figure 3.16 Example (2) of Cable Select 3.4.5 Power Up in Standby setting When pin C is grounded, the drive does not spin up at power on. 3-14 C141-E202-01EN
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
 |
 |
C141-E202-01EN
3-1
CHAPTER 3 Installation Conditions
3.1
Dimensions
3.2
Mounting
3.3
Cable Connections
3.4
Jumper Settings
This chapter gives the external dimensions, installation conditions, surface
temperature conditions, cable connections, and switch settings of the hard disk
drives.
For information about handling this hard disk drive and the system installation
procedure, refer to the following Integration Guide.
C141-E144