Fujitsu MHV2160BT Manual/User Guide
Fujitsu MHV2160BT - 160GB SATA/150 4200RPM 8MB Notebook Hard Drive Manual
 |
UPC - 683728124335
View all Fujitsu MHV2160BT manuals
Add to My Manuals
Save this manual to your list of manuals |
Fujitsu MHV2160BT manual content summary:
- Fujitsu MHV2160BT | Manual/User Guide - Page 1
CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E244 3-1 - Fujitsu MHV2160BT | Manual/User Guide - Page 2
Figure 3.1 illustrates the dimensions of the disk drive. All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge - Fujitsu MHV2160BT | Manual/User Guide - Page 3
3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be mounted in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero. The mounting frame is connected to Signal - Fujitsu MHV2160BT | Manual/User Guide - Page 4
Installation Conditions IMPORTANT Because of breather hole mounted to the HDD, do not allow this to close during mounting. Locating of breather hole is shown as Figure 3.3. For breather hole of Figure 3.3, at least, do not - Fujitsu MHV2160BT | Manual/User Guide - Page 5
in a cabinet refer to the ambient temperature at a point 3 cm from the disk drive. The ambient temperature must satisfy the temperature conditions described in Section 1.4, and the airflow must be considered to prevent the DE surface cover temperature from - Fujitsu MHV2160BT | Manual/User Guide - Page 6
Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Ensure that the disk drive disk drive. Pressing it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Static: When handling the device, disconnect - Fujitsu MHV2160BT | Manual/User Guide - Page 7
when you use an electric driver. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of the screw strictly. M3 0.49N • m (5 kgf • cm). - Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200-3056-8 SKY-8A - Fujitsu MHV2160BT | Manual/User Guide - Page 8
Installation Conditions 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. Figure 3.7 shows the locations of these connectors and terminals. SATA interface PCA and power connectors Figure 3.7 - Fujitsu MHV2160BT | Manual/User Guide - Page 9
for host system Table 3.2 lists the recommended specifications for the host interface connectors. Table 3.2 The recommended connector specifications for the host system Segment SATA interface and power supply Name Host receptacle Model (Manufacturer) 67492-0220 (Molex) or compatibles C141 - Fujitsu MHV2160BT | Manual/User Guide - Page 10
the host system must be compliant with the Serial ATA 1.0a specification. 3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
 |
 |
CHAPTER 3 Installation Conditions
3.1
Dimensions
3.2
Mounting
3.3
Connections with Host System
This chapter gives the external dimensions, installation conditions, surface
temperature conditions, cable connections, and switch settings of the hard disk
drives.
C141-E244
3-1