Home » Fujitsu Manuals » Hard Drives » Fujitsu MHW2040BH » Manual Viewer

Fujitsu MHW2040BH Manual/User Guide

Fujitsu MHW2040BH - Mobile 40 GB Hard Drive Manual

UPC - 102645907475

View all Fujitsu MHW2040BH manuals

Add to My Manuals
Save this manual to your list of manuals

Fujitsu MHW2040BH manual content summary:

Fujitsu MHW2040BH | Manual/User Guide - Page 1
CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E245 3-1
Fujitsu MHW2040BH | Manual/User Guide - Page 2
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the disk drive. All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the
Fujitsu MHW2040BH | Manual/User Guide - Page 3
3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be mounted in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero. The mounting frame is connected to Signal
Fujitsu MHW2040BH | Manual/User Guide - Page 4
Installation Conditions (3) Limitation of mounting Note) These dimensions are recommended values; if it is not possible to satisfy them, contact us. Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less
Fujitsu MHW2040BH | Manual/User Guide - Page 5
3.2 Mounting IMPORTANT Because of breather hole mounted to the HDD, do not allow this to close during mounting. Locating of breather hole is shown as Figure 3.3. For breather hole of Figure 3.3, at least, do not allow its around φ 3 to block. Figure 3.3 Location of breather C141-E254 3-5
Fujitsu MHW2040BH | Manual/User Guide - Page 6
in a cabinet refer to the ambient temperature at a point 3 cm from the disk drive. The ambient temperature must satisfy the temperature conditions described in Section 1.4, and the airflow must be considered to prevent the DE surface cover temperature from
Fujitsu MHW2040BH | Manual/User Guide - Page 7
Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Ensure that the disk drive disk drive. Pressing it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Static: When handling the device, disconnect
Fujitsu MHW2040BH | Manual/User Guide - Page 8
. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of the screw strictly. M3 0.49N • m (5 kgf • cm). - Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200-3056-8 SKY-8A (Color Seiden Mat) SS-6500 Maker
Fujitsu MHW2040BH | Manual/User Guide - Page 9
3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. Figure 3.7 shows the locations of these connectors and terminals. SATA interface PCA and power connectors
Fujitsu MHW2040BH | Manual/User Guide - Page 10
connectors. Table 3.2 The recommended connector specifications for the host system Segment SATA interface and power supply Name Host receptacle Model (Manufacturer) 67492-0220 (Molex) or compatibles IMPORTANT The above connector specifications for the host system indicate only that its
Fujitsu MHW2040BH | Manual/User Guide - Page 11
3.3 Connections with Host System 3.3.4 SATA interface cable connection The cable that connects the disk drive to the host system must be compliant with the Serial ATA 1.0a specification. 3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA
Fujitsu MHW2040BH | Manual/User Guide - Page 12
This page is intentionally left blank.