Home » Fujitsu Manuals » Hard Drives » Fujitsu MHW2080BK » Manual Viewer

Fujitsu MHW2080BK Manual/User Guide

Fujitsu MHW2080BK - Extended Duty Mobile 80 GB Hard Drive Manual

View all Fujitsu MHW2080BK manuals

Add to My Manuals
Save this manual to your list of manuals

Fujitsu MHW2080BK manual content summary:

Fujitsu MHW2080BK | Manual/User Guide - Page 1
CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E261 3-1
Fujitsu MHW2080BK | Manual/User Guide - Page 2
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the disk drive. All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the
Fujitsu MHW2080BK | Manual/User Guide - Page 3
3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be mounted in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero. The mounting frame is connected to
Fujitsu MHW2080BK | Manual/User Guide - Page 4
Installation Conditions (3) Limitation of mounting Note) These dimensions are recommended values; if it is not possible to satisfy them, contact us. Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less
Fujitsu MHW2080BK | Manual/User Guide - Page 5
3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to close during mounting. Locating of breather hole is shown as Figure 3.3. For breather hole of Figure 3.3, at least, do not allow its around φ 3 to block. Figure 3.3 Location of breather C141-E261 3-5
Fujitsu MHW2080BK | Manual/User Guide - Page 6
in a cabinet refer to the ambient temperature at a point 3 cm from the disk drive. The ambient temperature must satisfy the temperature conditions described in Section 1.4, and the airflow must be considered to prevent the DE surface cover temperature from
Fujitsu MHW2080BK | Manual/User Guide - Page 7
Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Ensure that the disk drive the cover of the disk drive. Pressing it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Static: When handling the
Fujitsu MHW2080BK | Manual/User Guide - Page 8
Installation Conditions - General notes Wrist strap Use the Wrist strap. ESD mat Shock absorbing mat Place the shock absorbing mat on the operation table, and place ESD mat on it. Do not hit HDD each other. Do not stack when carrying. Do not place HDD vertically to avoid falling down. Do not
Fujitsu MHW2080BK | Manual/User Guide - Page 9
3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. Figure 3.7 shows the locations of these connectors and terminals. SATA interface and power connectors
Fujitsu MHW2080BK | Manual/User Guide - Page 10
PCA side Figure 3.8 Power supply pins (CN1) 3.3.3 Connector specifications for host system The connector of host system for mating with the disk drive must be compliant with Serial-ATA Revision 2.5 specification. For detail of requirements about SATA interface connector, refer to the "Serial-ATA
Fujitsu MHW2080BK | Manual/User Guide - Page 11
the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle: When plugging together the disk drive SATA interface connector and the host receptacle or SATA interface cable connector, do not apply
Fujitsu MHW2080BK | Manual/User Guide - Page 12
This page is intentionally left blank.