Home » Fujitsu Manuals » Hard Drives » Fujitsu MHY2200BH » Manual Viewer

Fujitsu MHY2200BH Manual/User Guide

Fujitsu MHY2200BH - Mobile 200 GB Hard Drive Manual

View all Fujitsu MHY2200BH manuals

Add to My Manuals
Save this manual to your list of manuals

Fujitsu MHY2200BH manual content summary:

Fujitsu MHY2200BH | Manual/User Guide - Page 1
CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E262 3-1
Fujitsu MHY2200BH | Manual/User Guide - Page 2
Figure 3.1 illustrates the dimensions of the disk drive. All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of
Fujitsu MHY2200BH | Manual/User Guide - Page 3
(1) Orientation The disk drives can be mounted in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero. The mounting frame is connected to Signal Ground (SG). Use M3 screw for the mounting screw and the screw length should satisfy the specification in Figure 3.2. The
Fujitsu MHY2200BH | Manual/User Guide - Page 4
Installation Conditions (3) Limitation of mounting Note) These dimensions are recommended values; if it is not possible to satisfy them, contact us. Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less
Fujitsu MHY2200BH | Manual/User Guide - Page 5
3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to close during mounting. Locating of breather hole is shown as Figure 3.3. For breather hole of Figure 3.3, at least, do not allow its around φ 3 to block. Figure 3.3 Location of breather C141-E262 3-5
Fujitsu MHY2200BH | Manual/User Guide - Page 6
in a cabinet refer to the ambient temperature at a point 3 cm from the disk drive. The ambient temperature must satisfy the temperature conditions described in Section 1.4, and the airflow must be considered to prevent the DE surface cover temperature from
Fujitsu MHY2200BH | Manual/User Guide - Page 7
Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Ensure that the disk drive disk drive. Pressing it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Static: When handling the device, disconnect
Fujitsu MHY2200BH | Manual/User Guide - Page 8
when you use an electric driver. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of the screw strictly. M3 0.49N • m (5 kgf • cm). - Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200-3056-8 SKY-8A
Fujitsu MHY2200BH | Manual/User Guide - Page 9
with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. Figure 3.7 shows the locations of these connectors and terminals. SATA interface and power connectors PCA Figure 3.7 Connector locations C141-E262 3-9
Fujitsu MHY2200BH | Manual/User Guide - Page 10
the PCA side Figure 3.8 Power supply pins (CN1) 3.3.3 Connector specifications for host system The connector of host system for mating with the disk drive must be compliant with Serial-ATA Revision 2.5 specification. For detail of requirements about SATA interface connector, refer to the "Serial
Fujitsu MHY2200BH | Manual/User Guide - Page 11
must be compliant with the Serial ATA Revision 2.5 specification. 3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle: When
Fujitsu MHY2200BH | Manual/User Guide - Page 12
This page is intentionally left blank.