Home » Fujitsu Manuals » Hard Drives » Fujitsu MHZ2040BH » Manual Viewer

Fujitsu MHZ2040BH Manual/User Guide

Fujitsu MHZ2040BH - Mobile 40 GB Hard Drive Manual

View all Fujitsu MHZ2040BH manuals

Add to My Manuals
Save this manual to your list of manuals

Fujitsu MHZ2040BH manual content summary:

Fujitsu MHZ2040BH | Manual/User Guide - Page 1
CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E274 3-1
Fujitsu MHZ2040BH | Manual/User Guide - Page 2
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the disk drive. All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4
Fujitsu MHZ2040BH | Manual/User Guide - Page 3
3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be mounted in any direction. (2) Frame The MR head bias of the HDD disk
Fujitsu MHZ2040BH | Manual/User Guide - Page 4
Installation Conditions (3) Limitation of mounting Note) These dimensions are recommended values; if it is not possible to satisfy them, contact us. Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less
Fujitsu MHZ2040BH | Manual/User Guide - Page 5
3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to close during mounting. Locating of breather hole is shown as Figure 3.3. For breather hole of Figure 3.3, at least, do not allow its around φ 3 to block. Figure 3.3 Location of breather C141-E274 3-5
Fujitsu MHZ2040BH | Manual/User Guide - Page 6
Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to the ambient temperature at a point 3 cm from the disk drive. The ambient temperature must satisfy the temperature conditions described in Section 1.4, and the airflow must be
Fujitsu MHZ2040BH | Manual/User Guide - Page 7
areas) during and after installation. Mounting screw hole Cable connection Mounting screw hole Figure 3.5 Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Ensure that the disk drive is not affected by
Fujitsu MHZ2040BH | Manual/User Guide - Page 8
Installation Conditions - General notes Wrist strap Use the Wrist strap. ESD mat Shock absorbing mat Place the shock absorbing mat on the operation table, and place ESD mat on it. Do not hit HDD each other. Do not stack when carrying. Do not place HDD vertically to avoid falling down. Do not
Fujitsu MHZ2040BH | Manual/User Guide - Page 9
3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. Figure 3.7 shows the locations of these connectors and terminals. SATA interface and power connectors PCA Figure 3.7
Fujitsu MHZ2040BH | Manual/User Guide - Page 10
of host system for mating with the disk drive must be compliant with Serial-ATA Revision 2.5 specification. For detail of requirements about SATA interface connector, refer to the "Serial-ATA Revision 2.5." The connection reliability per number of insertion/extractions varies with the condition of
Fujitsu MHZ2040BH | Manual/User Guide - Page 11
3.3.4 SATA interface cable connection The cable that connects the disk drive to the host system must be compliant with the Serial ATA Revision 2.5 specification. 3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the
Fujitsu MHZ2040BH | Manual/User Guide - Page 12
This page is intentionally left blank.