Fujitsu XG700 Hardware Guide

Fujitsu XG700 - Switch Manual

Get Fujitsu XG700 - Switch PDF manuals and user guides View all Fujitsu XG700 manuals
Add to My Manuals
Save this manual to your list of manuals

Fujitsu XG700 manual content summary:

  • Fujitsu XG700 | Hardware Guide - Page 1
    P3N1-E041-01EN XG700 Hardware Guide
  • Fujitsu XG700 | Hardware Guide - Page 2
    Preface You have purchased the XG700, a compact, 12 port 10 Gigabit Ethernet layer 2 switch that achieves unsurpassed standards of high throughput and low-latency performance. This manual explains the procedures required to install your XG700 and should be read and understood before you start using
  • Fujitsu XG700 | Hardware Guide - Page 3
    and others, and to prevent property damage. When using the XG700, follow the instructions given in this manual. Warning notations Warnings are included throughout this manual in order to prevent injury to the user and/or material damage. These are two levels of warnings, both of which are composed
  • Fujitsu XG700 | Hardware Guide - Page 4
    socket or power strip), and the power outlet must be readily accessible. After the power is disconnected, contact the vendor's service department immediately. Continued use of the XG700 may cause an electric shock and fire. Note that in this case, the state of data in transmission is not guaranteed
  • Fujitsu XG700 | Hardware Guide - Page 5
    CAUTION This symbol indicates the possibility of minor or moderate personal injury, as well as damage to the XG700 and/or to other users and their property, if the XG700 is not used properly. Category Danger of device damage Danger of electromagnetic interference Danger of electric shock Danger
  • Fujitsu XG700 | Hardware Guide - Page 6
    required, contact the vendor's service department. Warning label The following warning label may be found on the rear of XG700. Do not attempt to • Use of this hardware guide, the XG700, its firmware, and the management software are the responsibility of the user. • Fujitsu and its partners accept no
  • Fujitsu XG700 | Hardware Guide - Page 7
    medical life support system, and missile launch control in weapon systems. Do not use the XG700 for High Safety Required Use without otherwise ensuring the safety level required. Fujitsu and its related companies assume no liability whatsoever for damages arising from use of the XG700 by the user in
  • Fujitsu XG700 | Hardware Guide - Page 8
    start the XG700. Chapter 3 Troubleshooting This chapter describes what you should do when your XG700 has problems. Appendix This appendix explains the specifications of the XG700, and should be referred to as necessary. Related manuals The following manuals are related to this manual. Consult them
  • Fujitsu XG700 | Hardware Guide - Page 9
    or trademarks of respective companies. The trademark ™ and ® have been omitted from this manual. Product Information The latest product information including technical information, update information, are available from the following web site: http://www.pfu.fujitsu.com/products/xg 8 About This
  • Fujitsu XG700 | Hardware Guide - Page 10
    Uninstalling the XG700 from a rack 26 2-3 Cable Connection 27 2-3-1 Connecting cables 27 2-3-2 Connecting the power cords 28 2-4 Basic Operation 30 2-4-1 Turning the XG700 on 30 2-4-2 Turning the XG700 off 30 Chapter 3 Troubleshooting 31 3-1 Start-up Problems 32 3-2 Hardware Problems 33
  • Fujitsu XG700 | Hardware Guide - Page 11
    Appendix 35 Appendix-A Specifications 36 A.1 Product Specifications 36 A.2 Installation Specifications 36 10 Contents
  • Fujitsu XG700 | Hardware Guide - Page 12
    Installation This chapter lists the items that should be in the XG700 package, describes the names and functions of the various components of the XG700. 1 1-1 Parts List 12 1-2 XG700 Components 14 1-3 Labels ...17
  • Fujitsu XG700 | Hardware Guide - Page 13
    following parts were included in your XG700 package. Contact the vendor's service department if any parts are missing and/or the manual has any missing or wrongly collated pages. Keep the hardware guide (this manual) and the CD-ROM in a safe place. 1 2 3 4 5 6 7 8 XG700 9 10 11 12 CD-ROM
  • Fujitsu XG700 | Hardware Guide - Page 14
    the rails to the rack posts. • CD-ROM Contains documents necessary to operate the XG700. • Hardware Guide A manual describing the XG700 hardware and related matters (this manual). • Rack Screws (Small) Pan-head screws for fixing the back rack mounting brackets (BL, BR) to the rails. • Wrist
  • Fujitsu XG700 | Hardware Guide - Page 15
    • Mng-LAN Lights when the XG700 is receiving power. Lights when there is a problem with the XG700. Lights when the XG700 is in an operable state. Used .3 ak compliant 10 Gigabit network served by the XG700. • Link/Act LEDs (Green) • Dump Switch Displays the condition of respective port. Each LED
  • Fujitsu XG700 | Hardware Guide - Page 16
    Inlet Power Unit LED • Power Switch • Power Supply Unit Used to turn the XG700 on/off. Supplies power to the XG700 (includes an exhaust fan). - Power Supply LED (Green/Orange) Green LED lights when the XG700 is on. Orange LED lights when there is a problem with the Power Supply Unit. • Rear
  • Fujitsu XG700 | Hardware Guide - Page 17
    XG700: Power LED, Alarm LED, and Status LED. The following explains the LED display under various conditions. XG700 trouble: XG700 Condition Power Alarm LED Status LED on failed part Problem Note that the XG700 does not shut itself off when trouble is detected. Any problems other than those
  • Fujitsu XG700 | Hardware Guide - Page 18
    1-3 Labels A warning sticker, product nameplate, product ID label, and MAC label are to be found in various places on the XG700. 1 Warning Sticker Product ID Label MAC Label Top view of XG700 Product Nameplate Warning sticker Obey the following warning: Right view of XG700 Labels 17
  • Fujitsu XG700 | Hardware Guide - Page 19
    2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 1 50/60Hz **** Kg 100-240V *** **** A/INPUT PFU Limited a FUJITSU company MADE IN JAPAN Product ID Label This indicates the model and serial number. MODEL ***** SER. NO :yy) Location Mng-LAN XG700 Port 1 Port 2 Port3 Port 4 Port 5 Port 6 Port 7
  • Fujitsu XG700 | Hardware Guide - Page 20
    This chapter explains how the user should proceed from installation to operation of the XG700. 2 2-1 Installation Overview 20 2-2 Installation Procedure 21 2-2-1 Installation requirements 21 2-2-2 Installing the XG700 in a rack 23 2-2-3 Uninstalling the XG700 from a rack 26 2-3 Cable Connection
  • Fujitsu XG700 | Hardware Guide - Page 21
    2-1 Installation Overview This section reviews the flow of work as the user proceeds from installation to operation of the XG700. Install the XG700 and the proceed with normal operation as follows: 1 Check the components "1-1 Parts List" 2 Check the set up area and install the XG700 "For Safe Use of
  • Fujitsu XG700 | Hardware Guide - Page 22
    (D) 19 inch rack. When installing in any other 19-inch rack, refer to the user guide provided with the rack. [540mm (W) 850mm (D) 19-inch rack] (Unit: mm) 540 Front Service area (Front) Rack (Top) Service area (Rear) 800 850 800 700 [700mm (W) 950mm (D) 19-inch rack] (Unit: mm) Front
  • Fujitsu XG700 | Hardware Guide - Page 23
    Specifications (P.36)". Using the XG700 outside the following ranges can shorten the lifetime or cause the failure of the XG700. Temperature (5 - 40°C) Humidity (20 - 80%RH) When installing the XG700 whether the XG700 can be installed in a given rack, contact the vendor's service department. CAUTION
  • Fujitsu XG700 | Hardware Guide - Page 24
    a rack The following explains how to install the XG700 in a 19-inch rack. 1. Take the XG700 out of its box. 2. Fix the cage nuts and rails to the rack posts. [When the rack has square post holes] Rack Post Rack Screws (
  • Fujitsu XG700 | Hardware Guide - Page 25
    [When the rack has round post holes] Rack Post Rack Screws (Large) Rack Post Rack Nut Front Rack Nut Rail L Rail R Rack Screws (Large) Rack Post Refer to Detail A Rack Post Rack Nut Clip the rack nuts onto the rack post so that the holes are lined up. Rack Nut Detail A [When the rack has
  • Fujitsu XG700 | Hardware Guide - Page 26
    mounting brackets (left, right, back-left, back-right) has three holes that should line up with matching holes on the sides of the XG700, as shown in the diagram. Attach each rack mounting bracket using the countersunk bracket screws provided. Bracket Screws Bracket Screws Rack Mounting Bracket
  • Fujitsu XG700 | Hardware Guide - Page 27
    Power Alarm Status Mng-LAN 1 2 3 4 5 6 7 8 9 10 11 12 2-2-3 Uninstalling the XG700 from a rack The following explains how to uninstall the XG700 from a rack. 1. Undo the rack screws that were used to fasten the XG700 to the rack. Rack Screws (Small) Rack Screws (Small) Rack Screws
  • Fujitsu XG700 | Hardware Guide - Page 28
    cords. 2-3-1 Connecting cables The cables need to be connected to the XG700 Xenpak modules. 1. Connect the cables to the XG700. Connect the cables to the Xenpak modules (Port 1 - Port 12) on the front of XG700. Console RS-232 Dump Power Alarm Status 2 Mng-LAN 1 2 3 4 5 6 7 8 9 10
  • Fujitsu XG700 | Hardware Guide - Page 29
    on, pulling, excessively bending, twisting, or overheating a power cord can damage it, and may cause electric shock or fire. • Do not use the XG700 with a damaged power cord, a damaged power plug, and/or a loose socket. Continued use under these conditions may cause a fire. • If the power plug
  • Fujitsu XG700 | Hardware Guide - Page 30
    plug at the other end of the power cord into the power strip or wall socket. WARNING • Unplug the XG700 during thunder-storms. Continued use under these conditions risks lightning damage to the XG700, and may cause a fire. • When you remove a power plug from its outlet, be sure to pull the only
  • Fujitsu XG700 | Hardware Guide - Page 31
    service department immediately. Continued use of the XG700 firmware has not been updated yet, then execute "system shutdown" from the command line. For details of the system shutdown dommand, refer to the "Command Reference" section in Refer the "XG700 User's Guide". 2. Just turn the power switch
  • Fujitsu XG700 | Hardware Guide - Page 32
    Troubleshooting This chapter describes what you should do when your XG700 has problems. 3 3-1 Start-up Problems 32 3-2 Hardware Problems 33
  • Fujitsu XG700 | Hardware Guide - Page 33
    department. Alarm LED lights, but the XG700 does not start up [Symptom] The XG700 has not started within a few minutes of the power switch being turned on. The Alarm LED (Orange) lights. [Cause] Probable hardware failure. [Action] Contact the vendor's service department. 32 Troubleshooting
  • Fujitsu XG700 | Hardware Guide - Page 34
    this case, turn the XG700 off and contact the vendor's service department. Power supply error When a power supply problem is detected, the Alarm up, contact the vendor's service department. Memory error Startup diagnostic tests are run after the power is turned. If a memory error is detected at
  • Fujitsu XG700 | Hardware Guide - Page 35
    34 Troubleshooting
  • Fujitsu XG700 | Hardware Guide - Page 36
    Appendix This appendix explains XG700 specifications. Appendix-A Specifications 36 A.1 Product Specifications 36 A.2 Installation Specifications 36
  • Fujitsu XG700 | Hardware Guide - Page 37
    This section details the specifications of XG700. A.1 Product Specifications The product specifications of the XG700 are as follows: Items 10 Gigabit ports Serial Port Management LAN Indicators Overview Port1 - Port12 Mng-LAN LED IEEE802.3ak compliant 10 Gigabit Ethernet port X 12 RS-232C
  • Fujitsu XG700 | Hardware Guide - Page 38
    XG700 Hardware Guide P3N1-E041-01EN Date of issue: September 2005 Issuing authority: PFU LIMITED Printed in Japan • Contents of this manual are not to be reproduced without permission from PFU. • The contents of this manual may be updated without notice. • PFU assumes no liability for damages to
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
XG700 Hardware Guide
P3N1-E041-01EN