Fujitsu fi-4860C Operation Manual
Fujitsu fi-4860C Manual
 |
View all Fujitsu fi-4860C manuals
Add to My Manuals
Save this manual to your list of manuals |
Fujitsu fi-4860C manual content summary:
- Fujitsu fi-4860C | Operation Manual - Page 1
P3PC-E167-04EN fi-4860C Image Scanner Operator's Guide - Fujitsu fi-4860C | Operation Manual - Page 2
- Fujitsu fi-4860C | Operation Manual - Page 3
INTRODUCTION Thank you for purchasing the fi-4860C Duplex Color Scanner. The fi-4860C is an image scanner designed to scan various documents in large quantities. FUJITSU fi series image scanners are known for high reliability and this scanner is no exceptions. The fi-4860C is designed to give you - Fujitsu fi-4860C | Operation Manual - Page 4
describes how to prepare the scanner for use. 2. INSTALLATION AND CONNECTIONS This chapter describes how to install and connect the scanner, and how to install the scanner application. We hope that this manual is useful in taking full advantage of the fi-4860C Duplex Color Scanner's features. ● ii - Fujitsu fi-4860C | Operation Manual - Page 5
protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications - Fujitsu fi-4860C | Operation Manual - Page 6
Le pésent appareil numérique n'ément pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescridtes dans le Réglesment sur le brouillage radioélectrique dicté par le ministere des Communications du Canada. Cet appareil numérique de la classe A - Fujitsu fi-4860C | Operation Manual - Page 7
Bescheinigung des Herstellers / Importeurs Hiermit wird bescheinigt, daß der/die/das fi-4860C • In Übereinsstimmung mit den Bestimmungen der AmtsblVfg 243/1991 funkentstört ist. •Der Deutschen Bundesport wurde das Inverkehrbringen dieses Gerätes angezeigt und die Berechtigung - Fujitsu fi-4860C | Operation Manual - Page 8
monitors, printers, facsimiles, copiers, scanners, and multifunction devices. Their standards flight control of aircraft, air traffic control, operation control in mass-transport systems, medical equipment safety in question is not ensured. The user should use this product with adopting measures for - Fujitsu fi-4860C | Operation Manual - Page 9
contained in the scanner parts. Disposing of the scanner should be conducted as required by local ordinances or regulations. Illegal Copying Reproducing bills, coins, government securities and passports, licenses issued by public author or civilian organizations, official documents, private paper is - Fujitsu fi-4860C | Operation Manual - Page 10
In This Manual References to operating systems (OS) are indicated as follows: Windows 95: Microsoft® Windows® 95 operating system. Windows 98: Microsoft® Windows® 98 operating system. Windows Me: Microsoft® Windows® Millennium Edition operating system. Windows 2000: Microsoft® Windows® 2000 - Fujitsu fi-4860C | Operation Manual - Page 11
IS NOT USED CORRECTLY, UNEXPECTED INJURY MAY BE CAUSED TO USERS OR BYSTANDERS. Also, store this manual in a convenient and safe place so that it can be by errors or omissions or by statements of any kind in this manual, its updates or supplements, whether such errors are omissions or statements - Fujitsu fi-4860C | Operation Manual - Page 12
. Warning Indications Used In This Manual This manual uses the following indications to ensure safe and correct use of this product, and to prevent possible danger and injury to the Operator and other persons. WARNING This indication alerts operators to an operation that, if not strictly observed - Fujitsu fi-4860C | Operation Manual - Page 13
to helpful advice regarding operation. HINT A TRIANGLE symbol indicates that special care and attention is required. The drawing inside the triangle shows the specific caution. A CIRCLE with a diagonal line inside shows action which users may not perform. The drawing inside or under the circle - Fujitsu fi-4860C | Operation Manual - Page 14
the screenshots in this manual are for the FUJITSU TWAIN32 scanner driver, ScandAll 21 Image Capturing Utility Software, FUJITSU ISIS scanner driver, QuickScanTM image capturing software and Adobe® Acrobat®. About Maintenance The user must not perform repairs on this scanner. Contact the store where - Fujitsu fi-4860C | Operation Manual - Page 15
■ Safety Precautions WARNING The following describes important warnings described in this manual. Do not touch the Power cable with wet hands. Do not touch the power plug with wet hands. Doing so might cause electric shock. Do - Fujitsu fi-4860C | Operation Manual - Page 16
the device or detect other problems such as smoke, strange smells or noises, immediately turn off the scanner and disconnect its power plug. Make sure that the smoking has stopped, and then contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider. ● xiv - Fujitsu fi-4860C | Operation Manual - Page 17
(water, small metal objects, liquids, etc.) get inside the scanner, immediately turn off the scanner and disconnect the power plug from the power outlet, contact the store where you purchased the scanner or the Maintenance Service Center. Pay particular attention to this warning in households where - Fujitsu fi-4860C | Operation Manual - Page 18
sure that the scanner is installed on a flat, level surface. Do not install the scanner on unstable surfaces. Install the scanner on a level surface that is free of vibration to prevent it from tilting. Install the scanner on a strong surface that will support the weight of the scanner and any other - Fujitsu fi-4860C | Operation Manual - Page 19
the cables, causing fire, electric shock or injuries. Before moving the scanner, be sure to disconnect the power plug from the power outlet, and floor is free of obstructions. Protect the scanner from static electricity. Install the scanner away from strong magnetic fields and other sources of - Fujitsu fi-4860C | Operation Manual - Page 20
scanner. Aerosol sprays cause dirt and dust to enter the scanner, resulting in scanner failure and malfunction. Avoid any contact when the scanner is in use. Avoid touching any part of the scanner safety. Do not install the scanner in the direct sunlight. Do not install the scanner in the direct - Fujitsu fi-4860C | Operation Manual - Page 21
Do not try to lift or move the scanner alone. This scanner is heavy (99lbs/45kg). When you carry the scanner, ensure that additional personnel are used. ● xix - Fujitsu fi-4860C | Operation Manual - Page 22
manual or on FUJITSU products to the following addresses: FUJITSU Website: http://www.fis.fujitsu.com/ E-mail: [email protected] FUJITSU AUSTRALIA LTD. Fujitsu House 2 Julius fujitsu.ca/ E-mail: [email protected] (For Sales Questions) [email protected] (For technical questions) FUJITSU - Fujitsu fi-4860C | Operation Manual - Page 23
-4001 Fax: (63-2)817-7576 Imaging Products Division, PFU LIMITED Solid Square East Tower, 580 Horikawacho, Saiwai-ku, Kawasaki-shi, Kanagawa 212-8563, Japan Phone: (81-44)540-4658 Fax: (81-44)540-4639 Website: http://imagescanner.fujitsu.com/ E-mail: [email protected] PFU LIMITED (Corporate - Fujitsu fi-4860C | Operation Manual - Page 24
Mode ........ 1-5 Basic Operations of the Operator Panel 1-6 Setting up the Hopper 1-14 Setting up the Stacker 1-15 Setting the Stacker Extension 1-17 Loading Documents on the Hopper 1-18 Inserting Documents Manually 1-21 Scanning Documents 1-23 How to use the Scanner Driver 1-27 2 SCANNING - Fujitsu fi-4860C | Operation Manual - Page 25
the Pick Roller Unit 4-9 Replacing the Brake Roller Unit 4-12 Replacing the Front-side Lamp 4-15 Replacing the Back-side Lamp 4-20 5 SOLVING COMMON PROBLEMS 5-1 Clearing Document Jams 5-2 Troubleshooting 5-8 Before Contacting a Service Provider 5-30 Labels on the Scanner 5-32 6 ADF DOCUMENT - Fujitsu fi-4860C | Operation Manual - Page 26
9 SCANNER SPECIFICATIONS 9-1 Basic Product Specifications 9-2 Installation Specifications 9-3 Dimensions 9-5 APPENDIX1 DROP-OUT COLOR AP-1 APPENDIX2 DOUBLE-FEED DETECTION CONDITIONS.... AP-2 APPENDIX3 MESSAGES OF OPERATOR PANEL AP-5 INDEX IN-1 ● xxiv - Fujitsu fi-4860C | Operation Manual - Page 27
be aware that when the FUJITSU TWAIN 32 scanner driver, or the FUJITSU ISIS scanner driver is updated, the screens and operations noted in this chapter may be changed slightly. In this case, please refer to the User's Guide provided with the update. 1.1 Turning the Scanner ON 1-2 1.2 Waking up the - Fujitsu fi-4860C | Operation Manual - Page 28
1.1 Turning the Scanner ON ■ Turning the power on 1. Press "I" side of the main line switch located on the back of the scanner. Power On Main line switch (Rear View) 1-2 1.1 Turning the Scanner ON - Fujitsu fi-4860C | Operation Manual - Page 29
2. Press the power button on the Operator panel. The power turns on and the green Power LED at the Operator panel lights. Operator panel LCD shows "Ready" to indicate the scanner is in the READY state. Power Button 1 BASIC SCANNER OPERATIONS 1.1 Turning the Scanner ON 1-3 - Fujitsu fi-4860C | Operation Manual - Page 30
■ Turning the Power off 1. On the Operator panel, press and hold down the Power button for two seconds or longer. 2. Press "O" side of the main line switch located on the back of the scanner. Power Off Main line switch (Rear View) 1-4 1.1 Turning the Scanner ON - Fujitsu fi-4860C | Operation Manual - Page 31
automatically switches to the Power Save Mode. In the Power Save Mode, the Operator panel LCD display goes out while the green LED stays lit. To wake up the scanner from the Power Save Mode, perform one of the following: 1 - Load documents on the hopper - Press a button, except Power button, on the - Fujitsu fi-4860C | Operation Manual - Page 32
1.3 Basic Operations of the Operator Panel This basic operation include how to enter setup mode and test mode. ■ Clearing error messages When an user recoverable error occurs, Check LED blinks to warn you and the error message is displayed on the LCD. Here is an example of an error - Fujitsu fi-4860C | Operation Manual - Page 33
height changes as follows by pressing (Exit button) for more than two seconds: BASIC SCANNER OPERATIONS 1. When the Hopper is at the bottom position, it moves up to 250 sheet position. 2. When the Hopper is at 250 sheet position, it moves down to the bottom position. 3. When the Hopper is at the - Fujitsu fi-4860C | Operation Manual - Page 34
position. 2. When the Hopper is at 250 sheet position, it moves down to the bottom position. 3. When the Hopper is at the highest position, it moves back to where it was when the scan operation started. ATTENTION Pressing (Previous button) does not change the position. The Hopper is positioned - Fujitsu fi-4860C | Operation Manual - Page 35
message This scanner has Abrasion counters to estimate service life of the consumables. When a counter (for the Pad ASSY, the Pick roller unit, the Brake roller unit, the Front-side lamp or the Back-side lamp) reaches the pre-set value, the LCD shows a message that the consumable's service life has - Fujitsu fi-4860C | Operation Manual - Page 36
Offline setup mode that can be entered only when the scanner is offline. Available functions are different depending on the mode. For the details, refer to "7 OPERATOR PANEL MENUS" on page 7-1. To enter these modes, follow the instructions below: - Online setup mode When the LCD indicates Ready - Fujitsu fi-4860C | Operation Manual - Page 37
u p No w! ! Re s e t t i n g hopper Wa r m i n g - u p No w! ! Wa i t i n g IF Re a d y Re a d y Press (Next button) xxxxx xxxxxx Press (Previous button) Mo d e Se l e c t 1 ! Set u p Mo d e Setup (Online) BASIC SCANNER OPERATIONS 1 1.3 Basic Operations of the Operator Panel 1-11 - Fujitsu fi-4860C | Operation Manual - Page 38
) or (Right arrow button) in [] screen to select [Setup] then press (Enter button). To exit this mode, turn off the power. 1-12 1.3 Basic Operations of the Operator Panel - Fujitsu fi-4860C | Operation Manual - Page 39
test mode, from the [] screen, press (Left arrow button) or (Right arrow button) , select [Test] and press Please see the Operator panel transition chart below. (Enter button). < MOD E SEL ECT> SET UP TEST < < TEST MODE > > 1 Press (Start button) or Test mode (Enter button - Fujitsu fi-4860C | Operation Manual - Page 40
BASIC SCANNER OPERATIONS 1.4 Setting up the Hopper 1. Gently flip down the Hopper table with holding its blue part. 1 1.4 Setting up the Hopper 1-14 - Fujitsu fi-4860C | Operation Manual - Page 41
1.5 Setting up the Stacker 1. Open the stacker. Stacker 1 BASIC SCANNER OPERATIONS 1.5 Setting up the Stacker 1-15 - Fujitsu fi-4860C | Operation Manual - Page 42
2. Push the opened stacker table lock into the scanner to lock it in place. When closing the stacker, pull out the stacker a little then fold it HINT closed. 1-16 1.5 Setting up the Stacker - Fujitsu fi-4860C | Operation Manual - Page 43
Stacker Extension 1. Hold the center of the blue part of the stacker extension to pull it out. Stopper 1 ATTENTION Stacker extension Do not use the stopper to pull out the stacker extension. Stopper may be damaged if you pull it. BASIC SCANNER OPERATIONS 1.6 Setting the Stacker Extension 1-17 - Fujitsu fi-4860C | Operation Manual - Page 44
20mm (1/2 to 3/4 inch). 2) Hold both ends and bend the documents into an arch. 15 to 20mm 3) Firmly holding the document with both hands, bend back the document as follows so that the bent section rises up in the middle of the document as follows. 4) Repeat steps 1) to 3) for a few times. 5) Rotate - Fujitsu fi-4860C | Operation Manual - Page 45
BASIC SCANNER OPERATIONS 3. Load the documents on the hopper. Place the documents face-up on the hopper table. 1 Hopper 4. Adjust the Side guides to the document width. Pressing the lock lever, slide the Side guides so that they contact the document sides. If there is space between the document - Fujitsu fi-4860C | Operation Manual - Page 46
maximum height mark on the inside of the Side guides. • For loading long documents, extend the hopper extension. Hopper Extension • A batch which consists of different sizes may cause feeding problems. 5. Start up the scanner application and scan the documents. For the details on how to scan using - Fujitsu fi-4860C | Operation Manual - Page 47
1.8 Inserting Documents Manually When the scanner is in Manual Feed Mode, set the documents as follows. 1. Lift the Pick roller until it is held by the magnet catch. The hopper table moves up to the feeding position. 1 Magnet catch Pick roller unit BASIC SCANNER OPERATIONS CAUTION Be careful not - Fujitsu fi-4860C | Operation Manual - Page 48
hopper table. For information on setting Manual feed timeout, refer to "7 OPERATOR HINT PANEL MENUS" on page 7-1. 3. Adjust the Side guides to the width of the documents. Load the documents so that the top edge of the documents contacts the hopper table guide plate. Hopper 1-22 1.8 Inserting - Fujitsu fi-4860C | Operation Manual - Page 49
. BASIC SCANNER OPERATIONS ATTENTION • For loading long documents on the hopper, extend the stacker extension. • For loading short documents on the hopper, adjust the stopper length. 3. Start up ScandAll 21 From [Start] menu, select [Program] - [Scanner Utility for Microsoft Windows] [ScandAll - Fujitsu fi-4860C | Operation Manual - Page 50
The [Select source] dialog box appears. Select [FUJITSU fi-4860CEAdij] (for TWAIN32 V8, [FUJITSU TWAIN 32]). Then click [Select]. 5. Click the [Display in scan preview screen] on the tool bar. The [TWAINDriver] dialog box (screen for setting scanning conditions) appears. 1-24 1.9 Scanning Documents - Fujitsu fi-4860C | Operation Manual - Page 51
BASIC SCANNER OPERATIONS 6. Set the scan resolution, document size and other scan conditions, and click the [Scan] button. For the details on settings in the [TWAIN Driver] dialog box, refer to the "Scanner Utility for Microsoft® Windows® User's Guide" on the scanner driver CD-ROM. 1 1.9 Scanning - Fujitsu fi-4860C | Operation Manual - Page 52
The image of the scanned document appears on the ScandAll 21 screen. For details on scanning various types of documents, refer to "2 SCANNING VARIOUS TYPES OF DOCUMENTS" on page 2-1. For details on ScandAll 21 function and operations, refer to ScandAll 21 Help. 1-26 1.9 Scanning Documents - Fujitsu fi-4860C | Operation Manual - Page 53
for scanning documents with FUJITSU image scanner fi series by using application software that complies with the TWAIN standard. The following describes the procedure with examples of ScandAll 21 for ordinary scanning by using this driver software. 1 ● Procedure for Basic Scanning Operation - Fujitsu fi-4860C | Operation Manual - Page 54
• [FUJITSU fi-4860CEAdij] for FUJITSU TWAIN32 V9 or • [FUJITSU TWAIN32] for FUJITSU TWAIN32 V8 then click the [Select] button. 4. Load the documents on the scanner. For details on loading documents, refer to "1.7 Loading Documents on the Hopper" on page 1-18. 5. Open the TWAIN Driver window. Select - Fujitsu fi-4860C | Operation Manual - Page 55
BASIC SCANNER OPERATIONS 6. Configure settings for scanning and click the [Scan] button. 1 For details about the settings on this window, refer to "Setting Window for FUJITSU TWAIN32 Scanner Driver." on page 1-31. 1.10 How to use the Scanner Driver 1-29 - Fujitsu fi-4860C | Operation Manual - Page 56
on the settings of the application software, images may not be displayed. For details, refer to the documentation or Help file of your application. e.x.) When you select [To File...] from the [Scan] menu of ScandAll 21, images of scanned documents are not displayed on the window. 7. Save the scanned - Fujitsu fi-4860C | Operation Manual - Page 57
BASIC SCANNER OPERATIONS ● Setting Window for FUJITSU TWAIN32 Scanner Driver. 1 You can perform settings for the FUJITSU TWAIN32 Scanner Driver on this window. The following describes the main setting items. • For details on each functions, refer to "FUJITSU TWAIN32 Scanner Driver Help" (appears by - Fujitsu fi-4860C | Operation Manual - Page 58
scanning. You can confirm the image of the documents in the preview window. [Close] button Saves the current settings and closes this window. [Reset] button Used to undo changes of settings. [Help] button Opens the "FUJITSU TWAIN32 Scanner Driver Help" window. The window also opens by pushing the - Fujitsu fi-4860C | Operation Manual - Page 59
unit displayed on the Setting Window for the FIJITSU TWAIN32 Scanner Driver. (Millimeters, Inches, and Pixels are available) [Filter] tab Select this tab for setting the image processing filter(s). Page Edge Filler: Fills up the margins of the scanned documents with a selected color. [Compression - Fujitsu fi-4860C | Operation Manual - Page 60
■ FUJITSU ISIS Scanner Driver FUJITSU ISIS Scanner Driver is designed for scanning documents with FUJITSU image scanner fi series by using application software that complies with the ISIS standard. The following describes the procedure with examples of QuickScanTM for ordinary scanning by using this - Fujitsu fi-4860C | Operation Manual - Page 61
BASIC SCANNER OPERATIONS 4. Select [Scan] - [New Batch] on the menu bar. 5. Select the profile for scanning. 1 •When creating a new profile Select one from selected profile will be deleted. When you added, edited or deleted a profile, go to the procedure 10. 1.10 How to use the Scanner Driver 1-35 - Fujitsu fi-4860C | Operation Manual - Page 62
] tab and click the [Scanner Settings] on the [Profile Editor] window. ⇒ The configuration window of ISIS driver appears. 7. Configure settings for scanning and click the [OK] button. For details on this dialog box, refer to "Configuration Window of FUJITSU ISIS Scanner Driver" on page 1-38. 1-36 - Fujitsu fi-4860C | Operation Manual - Page 63
SCANNER OPERATIONS ⇒ Scanned images are displayed on the window. Refer to the "QuickScan Overview" or the "QuickScan Help" for further information on functions and operations of QuickScan. After the installation of QuickScan, it is registered in the [Start] menu. 1.10 How to use the Scanner Driver - Fujitsu fi-4860C | Operation Manual - Page 64
FUJITSU ISIS Scanner Driver Image Mode Select a color mode suitable for the purpose from the menu. Black and White Scans data in binary (black and white). Distinguishes black from white according to the fixed threshold. This scanning mode is suitable for scanning line drawings and text documents - Fujitsu fi-4860C | Operation Manual - Page 65
-level Gray is selected at the Image Mode. [Side] The settings of this window are applied to the selected document side (Both, Front, Back). [More...] button Opens the [More Settings] window. Used for setting advanced features. BASIC SCANNER OPERATIONS 1 1.10 How to use the Scanner Driver 1-39 - Fujitsu fi-4860C | Operation Manual - Page 66
any value for the setting. [Endorser...] button This button displays [Endorser Configuration] dialog. This button is enabled when Endorser Option (separately sold) is installed. Refer to the documentation provided with the Endorser Option. [JPEG...] button 1-40 1.10 How to use the Scanner Driver - Fujitsu fi-4860C | Operation Manual - Page 67
BASIC SCANNER OPERATIONS Opens the JPEG Settings dialog box. Used for setting the compression rate of JPEG transfer, etc. 1 [About...] button This button displays the version information. ● Settings on the [Image Processing] window You can configure optional funcitons on this window. Gamma - Fujitsu fi-4860C | Operation Manual - Page 68
outline on the images. Magazines, Brochures, This option is suitable for scanning documents which have etc. texts and photos (e.g. magazines, brochures). Use Brightness Control Performs simple binary processing on the images. When this option is selected, you can manually adjust the threshold - Fujitsu fi-4860C | Operation Manual - Page 69
advanced functions on this window. ● Settings on the [Extra Features] window You can configure advanced features on this window. BASIC SCANNER OPERATIONS Dropout Color This option excludes a selected color (green, red, or blue) from scanned images. For example, if the document contains black text - Fujitsu fi-4860C | Operation Manual - Page 70
Double-feeds (phenomena that two or more sheets are accidentally fed). You can set conditions for detecting Double-feeds so that the scanner will stop its operation and display error messages. Double feeds are scanned by the differences in document lengths or thicknesses. Skew With this option - Fujitsu fi-4860C | Operation Manual - Page 71
when the FUJITSU TWAIN 32 scanner driver or the FUJITSU ISIS scanner driver is updated, the screens and operations noted in this chapter may change. In that case, please refer to the User's Guide provided with the update. 2.1 Scanning Documents with different widths 2-2 2.2 Saving Scanned Images in - Fujitsu fi-4860C | Operation Manual - Page 72
widths, you may get skewed images from smaller sized documents. Scanning documents of the same width is recommended. The following shows the procedure to scan batches of mixed size documents. 1. Sort the batch into the stacks of the same width documents. 2. Adjust the side guide to the width of each - Fujitsu fi-4860C | Operation Manual - Page 73
SCANNING VARIOUS TYPES OF DOCUMENTS 2.2 Saving Scanned Images in PDF Format If you would like to save scanned images in PDF format, you must first install Adobe® Acrobat® 5.0 or later on your PC. Adobe® Acrobat® 5.0 can be installed from the Adobe® Acrobat® CD-ROM provided. There are 2 ways for - Fujitsu fi-4860C | Operation Manual - Page 74
1. Load the documents on the hopper. 2. Start up ScandAll 21. Select [Program]-[Scanner Utility for Microsoft Windows]-[ScandAll21] from the [Start] menu. This will start up the application. 3. From the menu bar select [Scan] and then [To Adobe PDF] from the pull down menu. [TWAIN Driver] dialog is - Fujitsu fi-4860C | Operation Manual - Page 75
SCANNING VARIOUS TYPES OF DOCUMENTS 4. Select the scan resolution, document size and other scanning conditions, and then click the [Scan] botton. 2 5. To end scanning, click the [Close] button. The window for saving the image appears. 2.2 Saving Scanned Images in PDF Format 2-5 - Fujitsu fi-4860C | Operation Manual - Page 76
name and path. For details, refer to ScandAll 21 Help. Using Adobe Acrobat 5.0 Following shows the procedure for saving scanned images in PDF format. 1. Load the documents on the hopper. 2. Start up Adobe Acrobat 5.0. Select [Program] - [Adobe Acrobat] from the [Start] menu. This starts up Adobe - Fujitsu fi-4860C | Operation Manual - Page 77
VARIOUS TYPES OF DOCUMENTS 4. Select [FUJITSU fi-4860CEAdij] (for WindowsNT 4.0, select [FUJITSU TWAIN 32]) at [Device] and click [Scan] button. [TWAIN driver] dialog box is displayed. ATTENTION Select [Simplex] even if you intend to do duplex scanning. 2.2 Saving Scanned Images in PDF Format - Fujitsu fi-4860C | Operation Manual - Page 78
5. Select the scan resolution, document size and other scan conditions, and click the [Scan] button. 6. To end scanning, click the [Close] button. The scanned image is displayed. 2-8 2.2 Saving Scanned Images in PDF Format - Fujitsu fi-4860C | Operation Manual - Page 79
SCANNING VARIOUS TYPES OF DOCUMENTS 7. Select [Save as] or [Save] from [File] menu to save the scanned image. 2 For the details on Adobe Acrobat 5.0 operations, refer to the Adobe Acrobat 5.0 manual and Help. 2.2 Saving Scanned Images in PDF Format 2-9 - Fujitsu fi-4860C | Operation Manual - Page 80
If you save scanned documents by this procedure, the file size will be very HINT large. If you would like to reduce the usual) 1.Select [File (F)] - |[Print (P)...]. 2. Following dialog is displayed, then specify [Acrobat Distiller] for [Print Name]. 2-10 2.2 Saving Scanned Images in PDF Format - Fujitsu fi-4860C | Operation Manual - Page 81
SCANNING VARIOUS TYPES OF DOCUMENTS 3. Press the [Properties] button. 2 4, Press the [Adobe PDF settings] tab. 2.2 Saving Scanned Images in PDF Format 2-11 - Fujitsu fi-4860C | Operation Manual - Page 82
.) . 6. Click [OK] when finishing setup. 7. [Save as PDF File] dialog is displayed, then select the file name and click on [Save] button. 2-12 2.2 Saving Scanned Images in PDF Format - Fujitsu fi-4860C | Operation Manual - Page 83
image data. For example, if the document contains black text in green frames, you can set the scanner to get only the text and eliminate the green frames. To drop out a color, change the setting in the driver setting dialog box. The following shows examples for changing the setting of [TWAIN Driver - Fujitsu fi-4860C | Operation Manual - Page 84
to drop out from [Dropout Color] under [More]. For example, if the document contains black text in green frames, you can set the scanner to get only the text and eliminate the green frames. 3. Click [OK] button. [TWAIN Driver] dialog box will be redisplayed. Start scanning from this dialog box and - Fujitsu fi-4860C | Operation Manual - Page 85
2.4 Skipping blank Pages The following shows examples for changing settings in the [TWAIN Driver] dialogbox to skip blank pages at scanning documents. 1. Click the [Option ...] button in the [TWAIN Driver] dialogbox. 2 ⇒ The [Option] dialogbox appears. 2. Click the [Job/Cache] tab 2.4 Skipping blank - Fujitsu fi-4860C | Operation Manual - Page 86
Dots Ratio] or [White Dots Ratio] (ratio of black or white parts on the documents) for judging if the scanned document is recognized as a blank page by the scanner. The [TWAIN Driver] dialogbox will be redisplayed. Then, perform the scanning operation on the dialogbox. 2-16 2.4 Skipping blank Pages - Fujitsu fi-4860C | Operation Manual - Page 87
sheets are accidentally fed into the ADF at the same time. You can set the scanner to display an error message when it detects a doublefeed. To set conditions for the double-feed detection, change the settings in the driver in the [TWAIN Driver] dialogbox. SCANNING VARIOUS TYPES OF DOCUMENTS ⇒ The - Fujitsu fi-4860C | Operation Manual - Page 88
two or more document sheets are fed overlapped. Check length The scanner monitors the length of documents. It detects a double-feed by differences in the document length when two or more document sheets are fed overlapping. Check The scanner monitors both document overlapping and overlapping - Fujitsu fi-4860C | Operation Manual - Page 89
SCANNING VARIOUS TYPES OF DOCUMENTS 2.6 Correcting skewed Documents You can set the scanner so that skew of documents is detected and corrected automatically when skewed documents are fed into the ADF. The following shows examples for chaning the setting in the [TWAIN Driver] dialogbox to enable - Fujitsu fi-4860C | Operation Manual - Page 90
] menu. 4. Click the [OK] button. The display returns to the scanninig operation [TWAIN Driver] dialogbox. Then, perform the scanning operation on the dialogbox. ATTENTION When using either of the following documents, the automatic page size detection may not function correctly. Paper of weight - Fujitsu fi-4860C | Operation Manual - Page 91
you clean the scanner, turn off the power, and unplug the power cable from the outlet. 3.1 Cleaning Materials and Areas Requiring Cleaning .........3-2 3.2 Cleaning the Pad 3-5 3.3 Cleaning the Rollers 3-8 3.4 Cleaning the Transport Path 3-22 3.5 Cleaning the Discharge Brush 3-24 3.6 Cleaning - Fujitsu fi-4860C | Operation Manual - Page 92
Part No. Cleaning sheet CA99501-0016 Remarks 20 sheets/pack (* 1) Cleaner F2 CA99501-0014 1 bottle, 100ml/bottle (* 1) Isopropyl alcohol or CA99501-0013 Cleaner F1 1 bottle, 100ml/bottle Moisten cloth with this fluid and wipe the scanner FUJITSU scanner dealer where you purchased the scanner - Fujitsu fi-4860C | Operation Manual - Page 93
shows the standard cleaning frequency for each area requiring cleaning. Part to clean Pad Pick roller Brake roller Separation roller Feed roller Pinch roller Transport path Discharge brush Removable sheet guide Glass sheet guide Document width detection sensor Ultra sonic sensor SF0 SF1 SF1.5 SF2 - Fujitsu fi-4860C | Operation Manual - Page 94
scanner failure or malfunction. Vacuum the scanner instead. You must clean the following area more frequently when you use fi486PRFR or fi-486PRRF imprinters. The imprinter ink tend to stick to the document transport path. • Removable sheet guide • Glass sheet guide • Feed rollers • Pinch rollers - Fujitsu fi-4860C | Operation Manual - Page 95
raise it. CAUTION Raise the Upper transport unit fully, then lower it to engage lock before you put your hands inside of the scanner. 3 DAILY CARE 2. Pull the ADF release lever toward you and lift up the ADF upper sheet guide. ADF upper sheet guide ADF release lever 3.2 Cleaning the Pad 3-5 - Fujitsu fi-4860C | Operation Manual - Page 96
3. Press down on the upper part of the Guide plate with your fingers at the two positions shown and then rotate the plate toward you to remove it. Pad ASSY Guide plate 3-6 3.2 Cleaning the Pad - Fujitsu fi-4860C | Operation Manual - Page 97
in the reverse order of the removal.You should push it down then rotate back, so the installation can be done smoothly. 6. Lower the ADF upper sheet guide carefully. 7. Lift the Upper transport unit to release the safety lock, then lower the unit carefully and push the unit to close it completely - Fujitsu fi-4860C | Operation Manual - Page 98
screen. T02 Mu l t i f eed 4. Remove the protective paper from the cleaning sheet. 5. Place the cleaning sheet on the hopper table, align the left side with the hopper guide and with the adhesive side up. Press then the cleaning sheet is fed. (Start button), 3-8 3.3 Cleaning the Rollers - Fujitsu fi-4860C | Operation Manual - Page 99
[Hopper Empty] is displayed, press (Stop button). 7. Place the same cleaning sheet on the hopper table with adhesive side up by aligning the right side with the hopper guide. Press then the cleaning sheet is fed. (Start button), 3 DAILY CARE 8. When "Hopper Empty" is displayed, press (Stop - Fujitsu fi-4860C | Operation Manual - Page 100
Cleaning the Pick Rollers and the Separation Roller 1. Remove documents from the stacker. Pull up the lever on the right front of the Upper transport and then raise it. CAUTION Raise the Upper transport unit fully, then lower it to engage lock before you put your hands inside of the scanner. 3-10 - Fujitsu fi-4860C | Operation Manual - Page 101
2. While pulling the ADF lever toward you, lift up the ADF upper sheet guide. ADF upper sheet guide 3 ADF release lever DAILY CARE 3. Slide the Pick roller unit to the left to disengage the clutch ring from the shaft. Ring Pick roller unit Shaft 3.3 Cleaning the Rollers 3-11 - Fujitsu fi-4860C | Operation Manual - Page 102
4. Wipe both Pick rollers (2 positions) and the Separation roller using a clean lint free cloth moistened with cleaner F1. Ring Pick roller unit Separation roller 3-12 3.3 Cleaning the Rollers - Fujitsu fi-4860C | Operation Manual - Page 103
. When attaching the Pick roller unit, hold the unit as HINT shown. Engage the drive ring onto the drive shaft. Move left and align the clutch ring with the shaft and move right to engage. 3 Incorrect installation Correct installation DAILY CARE 6. Lower the ADF upper sheet guide carefully - Fujitsu fi-4860C | Operation Manual - Page 104
■ Cleaning the Brake roller unit 1. Remove documents from the stacker. Pull up the lever on the right front of the Upper transport and then raise it. CAUTION Raise the Upper transport unit fully, then lower it to engage lock before you put your hands inside of the scanner. 3-14 3.3 Cleaning the - Fujitsu fi-4860C | Operation Manual - Page 105
toward you and lift up the ADF sheet guide. ADF upper sheet guide 3 ADF release lever 3. Pressing down on the upper part of the Guide plate with your fingers at the two positions shown and then pull the plate toward you to remove it. Pad ASSY DAILY CARE Guide plate 3.3 Cleaning the Rollers 3-15 - Fujitsu fi-4860C | Operation Manual - Page 106
4. Turn the bail of the Brake roller upward and release the lock. Brake roller Bail 5. Pull the Brake roller toward you to remove it. 3-16 3.3 Cleaning the Rollers - Fujitsu fi-4860C | Operation Manual - Page 107
toward you, put the Brake roller into bracket and rotate down until it locks in. 8. Install the Guide plate in the reverse order of the removal. By pressing the Guide plate down, and pushing the Guide plate back, you can install it smoothly. 9. Lower the ADF upper sheet guide carefully. 10. Lift the - Fujitsu fi-4860C | Operation Manual - Page 108
■ Cleaning the Feed rollers 1. Remove documents from the stacker. Pull up the lever on the right front of the Upper transport and then raise it. CAUTION Raise the Upper transport unit fully, then lower it to engage lock before you put your hands inside of the scanner. 3-18 3.3 Cleaning the - Fujitsu fi-4860C | Operation Manual - Page 109
free cloth moistened with cleaner F2. Wipe the rollers thoroughly. If the rollers have black build-up, the feed reliability is affected. Feed rollers (in 12 locations) 3 DAILY CARE CAUTION Use cleaner F2 only on metal rollers (only the Feed rollers). 3. Lift the Upper transport unit to release - Fujitsu fi-4860C | Operation Manual - Page 110
■ Cleaning the Pinch rollers 1. Remove documents from the stacker. Pull up the lever on the right front of the Upper transport and then raise it. CAUTION Raise the Upper transport unit fully, then lower it to engage lock before you put your hands inside of the scanner. 3-20 3.3 Cleaning the - Fujitsu fi-4860C | Operation Manual - Page 111
DAILY CARE 2. Wipe the pinch rollers using a cloth moistened with cleaner F1. Pinch roller (in 12 locations) 3 3. Lift the Upper transport unit to release the safety lock, then lower the unit carefully and push the unit to close it completely. 3.3 Cleaning the Rollers 3-21 - Fujitsu fi-4860C | Operation Manual - Page 112
Cleaning the Transport path 1. Remove documents from the stacker first. Pull up the lever on the right front of the Upper transport and then raise it. CAUTION Raise the Upper transport unit fully, then lower it to engage lock before you put your hands inside of the scanner. 3-22 3.4 Cleaning the - Fujitsu fi-4860C | Operation Manual - Page 113
the path. HINT Do not use aerosol sprays to clean the path. 3 CAUTION Do not use HIgh Pressure Air to blow dust out of the scanner. This will contaminate the optics and mechanism. Transport path DAILY CARE 3. Lift the Upper transport unit to release the safety lock, then lower the unit - Fujitsu fi-4860C | Operation Manual - Page 114
Discharge Brush 1. Remove documents from the stacker. Pull up the lever on the right front of the Upper transport and then raise it. CAUTION Raise the Upper transport unit fully, then lower it to engage lock before you put your hands inside of the scanner. 3-24 3.5 Cleaning the Discharge Brush - Fujitsu fi-4860C | Operation Manual - Page 115
2. Pull the ADF release lever toward you and lift up the ADF sheet guide. ADF upper sheet guide 3 ADF release lever DAILY CARE 3. Slide the Pick roller unit to the left to disengage the clutch ring from the shaft. Ring Pick roller unit Shaft 3.5 Cleaning the Discharge Brush 3-25 - Fujitsu fi-4860C | Operation Manual - Page 116
of the Guide plate with your fingers at the two positions shown and then rotate the plate toward you to remove it. Pad ASSY Guide plate 5. Release the lock and then hold and rotate the bail of the Pick roller unit upward to release the lock. Brake roller Bail 3-26 3.5 Cleaning the Discharge Brush - Fujitsu fi-4860C | Operation Manual - Page 117
you to remove it. 3 7. Wipe off the dust from the two discharge brushes: one at the Pick roller side, the other at the Brake roller side. Discharge brush(for Pick roller unit) Discharge brush(for brakeroller) 8. Re-install the Brake roller unit in the reverse order of its removal. By holding the - Fujitsu fi-4860C | Operation Manual - Page 118
You should push it down and rotate back then the installation can be done smoothly. 10. Lower the ADF upper sheet guide slowly. 11. Lift the Upper transport unit to release the safety lock, then lower the unit carefully and push the unit to close it completely. 3-28 3.5 Cleaning the Discharge Brush - Fujitsu fi-4860C | Operation Manual - Page 119
3.6 Cleaning the Glass Surface ■ Cleaning of the removable sheet guide The Lamps get very hot during use. Wait until the Lamps are cooled down CAUTION before touching. Do not allow F1 cleaner to contact hot lamps. 3 DAILY CARE 1. Remove documents from the stacker. Pull up the lever on the - Fujitsu fi-4860C | Operation Manual - Page 120
2. Use your index fingers to lift both ends of the removable sheet guide. 3. Lift the right side first. 4. Shift the sheet guide leftward while lifting it up to remove. Removable sheet guide 3-30 3.6 Cleaning the Glass Surface - Fujitsu fi-4860C | Operation Manual - Page 121
DAILY CARE 5. Wipe the both sides of the glass surface using a clean lint free cloth moistened with cleaner F1. 3 6. Attach the removable sheet guide in the reverse order of its removal. 7. Lift the Upper transport unit to release the safety lock, then lower the unit carefully and push the - Fujitsu fi-4860C | Operation Manual - Page 122
■ Cleaning the Glass Sheet Guide CAUTION The Lamps get very hot during use. Wait until the Lamps are cooled down before touching. Do not allow F1 cleaner to contact hot lamps. 1. Remove documents from the stacker. Pull up the lever on the right front of the Upper transport and then raise it. - Fujitsu fi-4860C | Operation Manual - Page 123
DAILY CARE 2. Push down on the Glass sheet guide tab to open the Glass sheet guide. 3 This picture is side View. Glass sheet guide 3.6 Cleaning the Glass Surface 3-33 - Fujitsu fi-4860C | Operation Manual - Page 124
using a clean lint free cloth moistened with cleaner F1. Glass sheet guide Tab 4. Lift the tabs until the Guide locks in. Close the Glass sheet guide. Make sure that the metal part locks. 5. Lift the Upper transport unit to release the safety lock, then lower the unit carefully and push the unit - Fujitsu fi-4860C | Operation Manual - Page 125
sensors (6 positions) 1. Remove documents from the stacker. Pull up the lever on the right front of the Upper transport and then raise it. 3 Raise the Upper transport unit fully, then lower it to engage lock before you CAUTION put your hands inside of the scanner. DAILY CARE 3.7 Cleaning the - Fujitsu fi-4860C | Operation Manual - Page 126
hand to keep it open. 4. Wipe the six sensor surfaces with a clean lint free cloth moistened with cleaner F1. Document width sensor(in 6 locations) 5. Lower the ADF upper sheet guide gently. 6. Lift the Upper transport unit to release the safety lock, then lower the unit carefully and push the unit - Fujitsu fi-4860C | Operation Manual - Page 127
sensor and SF1 sensor. 1. Remove documents from the stacker. Pull up the lever on the right front of the Upper transport and then raise it. CAUTION Raise the Upper transport unit fully, then lower it to engage lock before you put your hands inside of the scanner. 3 DAILY CARE 3.7 Cleaning the - Fujitsu fi-4860C | Operation Manual - Page 128
open. 4. Wipe SF0 and SF1 sensor surfaces with a clean lint free cloth moistened with cleaner F1. SF1 Sensor SF0 Sensor 5. Lower the ADF upper sheet guide gently. 6. Lift the Upper transport unit to release the safety lock, then lower the unit carefully and push the unit to close it completely - Fujitsu fi-4860C | Operation Manual - Page 129
sensor and SF2 sensor 1. Remove documents from the stacker. Pull up the lever on the right front of the Upper transport and then raise it. CAUTION Raise the Upper transport unit fully, then lower it to engage lock before you put your hands inside of the scanner. 3 DAILY CARE 3.7 Cleaning the - Fujitsu fi-4860C | Operation Manual - Page 130
2. Wipe SF1.5 and SF2 sensor surfaces with a clean lint free cloth moistened with cleaner F1. SF2 Sensor SF1.5 Sensor 3. Lift the Upper transport unit to release the safety lock, then lower the unit carefully and push the unit to close it completely. 3-40 3.7 Cleaning the Sensors - Fujitsu fi-4860C | Operation Manual - Page 131
Never replace the Lamp without turning off the power. 3 Do not allow F1 cleaner to contact hot lamps. DAILY CARE ■ Front-side lamp 1. Remove documents from the stacker. Pull up the lever on the right front of the Upper transport and then raise it. CAUTION Raise the Upper transport unit - Fujitsu fi-4860C | Operation Manual - Page 132
2. Push down on the Glass sheet guide tab to open the Glass sheet guide. This picture is side View. 3-42 3.8 Cleaning the Lamps - Fujitsu fi-4860C | Operation Manual - Page 133
DAILY CARE Glass sheet guide 3 3.8 Cleaning the Lamps 3-43 - Fujitsu fi-4860C | Operation Manual - Page 134
3. Pull down on the tab to release the Lamp socket covers attached to the both ends of the Lamp to remove them. Tab 4. Rotate the Lamp a half turn so that the terminals on each end align with the slot on the Lamp socket. Then remove the Lamp from the socket. Lamp socket 3-44 3.8 Cleaning the Lamps - Fujitsu fi-4860C | Operation Manual - Page 135
in the reverse order of its removal. Make sure that the clear portion of the Lamp faces down. DAILY CARE ATTENTION If the Lamp is installed with the clear portion facing incorrect direction, an error due to insufficient light occurs. 3.8 Cleaning the Lamps 3-45 - Fujitsu fi-4860C | Operation Manual - Page 136
socket cover hook to the Lamp frame then rotate forward as shown below, to attach the covers. Lamp socket cover 8. Close the Glass sheet guide. Make sure that the guide is fixed firmly. 9. Lift the Upper transport unit to release the safety lock, then lower the unit carefully and push the unit to - Fujitsu fi-4860C | Operation Manual - Page 137
DAILY CARE ■ Back-side lamp 1. Push back blue latch to release the side cover, then open. 3 Side cover 2. Hold the handle (blue part) and pull the Back-side lamp unit out of the scanner. 3.8 Cleaning the Lamps 3-47 - Fujitsu fi-4860C | Operation Manual - Page 138
3. Rotate the Lamp a half turn so that the terminals on each end align with the slot on the Lamp socket and remove the Lamp from the unit. Lamp socket Backside lamp unit 4. Clean the clear portion of the Lamp with a dry cloth. Clear portion 3-48 3.8 Cleaning the Lamps - Fujitsu fi-4860C | Operation Manual - Page 139
sure that the clear portion of the Lamp faces up. 3 DAILY CARE ATTENTION If the Lamp is installed with the clear portion facing incorrect direction, an error due to insufficient light occurs. 6. Install the Back-lamp in the reverse order of its removal. Make sure the connectors meet properly - Fujitsu fi-4860C | Operation Manual - Page 140
3-50 3.8 Cleaning the Lamps - Fujitsu fi-4860C | Operation Manual - Page 141
This chapter describes how to replace consumables. 4.1 Consumables and Replacement Cycle 4-2 4.2 How to check the Abrasion Counter 4-3 4.3 Replacing the Pad ASSY 4-4 4.4 Replacing the Pick Roller Unit 4-9 4.5 Replacing the Brake Roller Unit 4-12 4.6 Replacing the Front-side Lamp 4-15 - Fujitsu fi-4860C | Operation Manual - Page 142
to each counter on this scanner. Descriptions Lamp Pad ASSY Pick Roller Unit Brake Roller Unit Print Cartridge Part No. PA83950-0290 CA04315-G730 PA03296-F711 CA04315-F705 CA00050-0262 Standard replacement cycle 1,000 Hours(60,000minutes) 300,000 sheets or 1 year 300,000 sheets or 1 year 300,000 - Fujitsu fi-4860C | Operation Manual - Page 143
the counter from the Operator panel The number displayed on the right bottom of LCD in the "Ready" status shows the consumables count. The Abrasion counter, shown below indicates the highest cumulative number of sheets scanned by the PAD ASSY, the Pick roller unit or the Brake roller unit. Batch - Fujitsu fi-4860C | Operation Manual - Page 144
Replacing the Pad ASSY 1. Remove documents from the stacker. Pull up the lever on the right front of the Upper transport and then raise it. CAUTION Raise the Upper transport unit fully, then lower it to engage lock before you put your hands inside of the scanner. 4-4 4.3 Replacing the Pad ASSY - Fujitsu fi-4860C | Operation Manual - Page 145
and lift up the ADF sheet guide. ADF upper sheet guide 4 ADF release lever 3. Press down on the upper part of the Guide plate with your fingers at the two positions shown and then rotate the plate toward you to remove it. Pad ASSY REPLACEMENT OF CONSUMABLES Guide plate 4.3 Replacing the Pad ASSY - Fujitsu fi-4860C | Operation Manual - Page 146
Pad (cleaning area) Guide plate Pad ASSY 4-6 4.3 Replacing the Pad ASSY - Fujitsu fi-4860C | Operation Manual - Page 147
REPLACEMENT OF CONSUMABLES 4. Remove the Pad ASSY from the Guide plate by pushing the removal metal scroll down and then release hooks. 4 4.3 Replacing the Pad ASSY 4-7 - Fujitsu fi-4860C | Operation Manual - Page 148
firmly, paper feed errors such as document jams may occur. 6. Install the Guide plate in the reverse order of the removal. By pressing the Guide plate down and pushing the Guide plate back then you can install it smoothly. 7. Lower the ADF upper sheet guide gently. 8. Lift the Upper transport unit - Fujitsu fi-4860C | Operation Manual - Page 149
the Pick Roller Unit 1. Remove documents from the stacker. Pull up the lever on the right front of the Upper transport and then raise it. CAUTION Raise the Upper transport unit fully, then lower it to engage lock before you put your hands inside of the scanner. 4 REPLACEMENT OF CONSUMABLES - Fujitsu fi-4860C | Operation Manual - Page 150
2. While pulling the ADF lever toward you, lift up the ADF upper sheet guide. ADF upper sheet guide ADF release lever 3. Lift up the Pick roller unit a little. Slide the Pick roller unit to the left to disengage the clutch ring from the shaft. Ring Pick roller unit Shaft 4-10 4.4 Replacing the - Fujitsu fi-4860C | Operation Manual - Page 151
. 4 Incorrect installation Correct installation REPLACEMENT OF CONSUMABLES 5. Lower the ADF upper sheet guide carefully. 6. Lift the Upper transport unit to release the safety lock, then lower the unit carefully and push the unit to close it completely. 7. Clear the Pick roller counter. Please - Fujitsu fi-4860C | Operation Manual - Page 152
and then raise it. CAUTION Raise the Upper transport unit fully, then lower it to engage lock before you put your hands inside of the scanner. 2. Pull the ADF release lever toward you and lift up the ADF sheet guide. ADF upper sheet guide ADF release lever 4-12 4.5 Replacing the Brake Roller Unit - Fujitsu fi-4860C | Operation Manual - Page 153
OF CONSUMABLES 3. Press down on the upper part of the Guide plate with your fingers at the two positions shown and rotate the plate toward you to remove it. Pad ASSY 4 Guide plate 4. Turn the bail of the Brake roller upward and release the lock. Brake roller Bail 4.5 Replacing the Brake Roller Unit - Fujitsu fi-4860C | Operation Manual - Page 154
you, put the Brake roller into bracket and rotate down until it locks in. 7. Install the Guide plate in the reverse order of the removal. By pressing the Guide plate down and pushing the Guide plate back, you can install it smoothly. 8. Lower the ADF upper sheet guide carefully. 9. Lift the Upper - Fujitsu fi-4860C | Operation Manual - Page 155
-side Lamp CAUTION Never replace the Lamp without turning off the power. Wait 5 minutes after turning off the power before touching the Lamp. 4 1. Remove documents from the stacker. Pull up the lever on the right front of the Upper transport and then raise it. CAUTION Raise the Upper transport - Fujitsu fi-4860C | Operation Manual - Page 156
2. Pull down the Glass sheet guide tab and open the Glass sheet guide. This picture is side View. Glass sheet guide 4-16 4.6 Replacing the Front-side Lamp - Fujitsu fi-4860C | Operation Manual - Page 157
REPLACEMENT OF CONSUMABLES 3. Pulling down the Lamp socket covers attached to the both end of the Lamp sockets and remove them. Tab 4 4. Rotate the Lamp a half turn so - Fujitsu fi-4860C | Operation Manual - Page 158
5. Install a new Lamp in the reverse order of the removal. Make sure that the clear portion of the Lamp faces down. ATTENTION If the Lamp is installed with the clear portion facing incorrect direction, an error due to insufficient light occurs. 4-18 4.6 Replacing the Front-side Lamp - Fujitsu fi-4860C | Operation Manual - Page 159
the metal part is fixed firmly. Lamp socket cover 4 REPLACEMENT OF CONSUMABLES 7. Close the glass sheet guide. Make sure that the guide is fixed on page 7-34. You can check the cumulative lamp-on time from the Operator HINT panel Test mode. For the details, refer to the section "7.5 Test Mode - Fujitsu fi-4860C | Operation Manual - Page 160
4.7 Replacing the Back-side Lamp CAUTION Never replace the Lamp without turning off the power. Wait 5 minutes after turning off the power before touching the Lamp. 1. Pull and open the side cover. Side cover 4-20 4.7 Replacing the Back-side Lamp - Fujitsu fi-4860C | Operation Manual - Page 161
REPLACEMENT OF CONSUMABLES 2. Hold the handle (blue part) and pull out the Back-side lamp unit. 4 3. Rotate the Lamp a half turn so that the terminals on each end align with the slot on - Fujitsu fi-4860C | Operation Manual - Page 162
4. Attach a new Lamp following the reverse order of old lamp removal. Make sure that the clear portion of the Lamp faces up. ATTENTION If the Lamp is installed with the clear portion facing incorrect direction, an error due to insufficient light occurs. 4-22 4.7 Replacing the Back-side Lamp - Fujitsu fi-4860C | Operation Manual - Page 163
OF CONSUMABLES 6. Close the side cover. Confirm that the cover is closed securely. 7. Clear the Rear-side lamp counter. Please refer to the section "7.3 Setup Mode Details", " 9. Abrasion counter (Abrasion CNT) reset " on page 7-34. You can check the cumulative lamp-on time from the Operator panel - Fujitsu fi-4860C | Operation Manual - Page 164
4-24 4.7 Replacing the Back-side Lamp - Fujitsu fi-4860C | Operation Manual - Page 165
describes how to clear document jams, how to remedy other problems, items to be checked before contacting an authorized service provider and how to check labels on the scanner. 5.1 Clearing Document Jams 5-2 5.2 Troubleshooting 5-8 5.3 Before Contacting a Service Provider 5-30 5.4 Labels on - Fujitsu fi-4860C | Operation Manual - Page 166
• Be careful not to get injured during jam removal. • When removing jammed documents, be careful not to get your neckties or necklaces entangled inside the scanners. • The surface of the glass may be hot during the operation. Take care not to get burned. ■ Removing jams from the hopper or the - Fujitsu fi-4860C | Operation Manual - Page 167
, lift up the ADF upper sheet guide. ADF upper sheet guide 5 SOLVING COMMON PROBLEMS ADF release lever 3. Remove the jammed document. ATTENTION - Staples and paper clips etc. can cause document jams. - Make sure you check the document and the document transport path for obstructions before you - Fujitsu fi-4860C | Operation Manual - Page 168
on the stacker. Pull up the lever on the right front of the Upper transport and then raise it. ADF upper sheet guide ADF release lever 2. Pull out the jammed document to the stacker. 3. Lift the Upper transport unit to release the safety lock, then lower the unit carefully and push the unit - Fujitsu fi-4860C | Operation Manual - Page 169
■ Document separation force adjustment If the following error occurs frequently, adjust the brake force of the Brake roller using setup mode. - Double-feed - Mis-pick - Paper jam1 5 SOLVING COMMON PROBLEMS 1. Enter into the setup mode. Please refer to the section "1 Basic Operations of the - Fujitsu fi-4860C | Operation Manual - Page 170
feed" occurs frequently "Mis-pick" or "Document jam" occurs frequently Strong Less strong Increase document Decrease document separation force separation force Medium (Factory default setting) Medium Weak Weak If Mis-pick occurs frequently, adjust the Pick roller rotation speed. Press (Next - Fujitsu fi-4860C | Operation Manual - Page 171
Pick speed Fast (Factory default) Mid Slow Mis-pick occurs frequently Decrease pick speed ATTENTION When you set pick speed at "Mid" or "Slow", scanning speed is reduced. 5 SOLVING COMMON PROBLEMS 5.1 Clearing Document Jams 5-7 - Fujitsu fi-4860C | Operation Manual - Page 172
the following flowchart to determine the trouble. If you can not resolve the trouble after following the flowcharts, please check the items in section "5.3 Before Contacting a Service Provider" on page 5-30, and then contact an authorized FUJITSU Scanner service provider. 5-8 5.2 Troubleshooting - Fujitsu fi-4860C | Operation Manual - Page 173
you turned on the main line Press the "I" side of the main switch? line switch. YES NO Have you pushed the power button on the operator panel? YES Press the power button. Contact an authorized FUJITSU Scanner service provider. SOLVING COMMON PROBLEMS 5 5.2 Troubleshooting 5-9 - Fujitsu fi-4860C | Operation Manual - Page 174
it up. The scanner operation is normal. YES Contact an authorized FUJITSU Scanner service provider. (* ) Press any button except Power button. The Power button will not work to wake up the scanner. Pressing the power button more than 2 seconds will turn off the power. 5-10 5.2 Troubleshooting - Fujitsu fi-4860C | Operation Manual - Page 175
Symtom3 Scanning does not start. NO Are the documents loaded properly on the hopper? Load the documents centered in the hopper. YES Is the NO Set the SCSI ID correctly from the operator panel of the scanner. (* 1) Continued on next page SOLVING COMMON PROBLEMS 5 5.2 Troubleshooting 5-11 - Fujitsu fi-4860C | Operation Manual - Page 176
applications and select the scanner from only one application. The scanner operation is normal. YES Check LCD display for error. Eliminate the cause of user recoverable errors. Is the LED still blinking? YES NO The scanner operation is normal. Continued on next page 5-12 5.2 Troubleshooting - Fujitsu fi-4860C | Operation Manual - Page 177
scanner operation is normal. NO The scanner operation is normal. Contact an authorized FUJITSU Scanner service provider. 5 SOLVING COMMON PROBLEMS (* 1) For the details on how to set SCSI ID, refer to the section "7.3 Setup Mode Details", "19. Setting SCSI ID" on page 7-49. 5.2 Troubleshooting - Fujitsu fi-4860C | Operation Manual - Page 178
or dithering mode on your PC. YES Is the document path, the Removable NO sheet guide, the Glass sheet guide and/or the Lamp(s) clean? YES Clean the scanner completely. (* 2) Are the Lamps installed correctly? NO Re-install the lamps correctly. (* 3) YES Continued on next page 5-14 - Fujitsu fi-4860C | Operation Manual - Page 179
Continued from the previous page Contact an authorized FUJITSU Scanner service provider. 5 SOLVING COMMON PROBLEMS (* 1) If Binary mode is used, the scanned image of a photograph may not be good. Depending on the applications used, the method to specify "Photo" mode and the name of the mode can - Fujitsu fi-4860C | Operation Manual - Page 180
NO Is the document path, the Removable sheet guide, the Glass sheet guide and/or the Lamp(s) clean? YES Select "Line Art" mode from your PC. (* 1) Clean the scanner completely. (* 2) Contact an authorized FUJITSU Scanner service provider. (* 1) If halftone mode is used, the scanned image of text - Fujitsu fi-4860C | Operation Manual - Page 181
Is the document path, the Removable sheet guide, the Glass sheet guide and/or the Lamp(s) clean? YES NO Is the scanner installed on a flat and NO level surface? Clean the scanner completely. (* ) Install the scanner on a flat and level surface. YES Contact an authorized FUJITSU Scanner service - Fujitsu fi-4860C | Operation Manual - Page 182
document and is the "Line Art" mode selected. YES NO Are the Lamp(s) more than 1,000 hours old? Has the Lamp(s) burned out? (* 2) NO YES Clean the Removable sheet guide , and the Glass sheet guide. (* 1) Select "Photo" mode. Replace the Lamp. (* 3) Contact an authorized FUJITSU Scanner service - Fujitsu fi-4860C | Operation Manual - Page 183
scanner operation is normal. Contact an authorized FUJITSU Scanner service provider. 5 SOLVING COMMON PROBLEMS (* ) For the message display contents and the error recovery method, refer to "APPENDIX3 MESSAGES OF OPERATOR PANEL", "Error message (Temporary error)" on page AP-9. 5.2 Troubleshooting - Fujitsu fi-4860C | Operation Manual - Page 184
Symptom9 The Check LED lights right after power on. Turn off the power and on again. Is the check LED lit again? YES NO The scanner operation is normal. Contact an authorized FUJITSU Scanner service provider. 5-20 5.2 Troubleshooting - Fujitsu fi-4860C | Operation Manual - Page 185
satisfy the requirements. (* 2) Fan the documents a few times before loading. YES Are the documents recently printed on a copier or Laser printer? NO YES Fan the documents a few times to eliminate static electricity. Continued on next page SOLVING COMMON PROBLEMS 5 5.2 Troubleshooting 5-21 - Fujitsu fi-4860C | Operation Manual - Page 186
Pad ASSY worn out? YES Replace the Pad ASSY. (* 4) NO NO Is the Pad ASSY installed properly? Install the Pad ASSY properly. (* 4) YES Are the Pick roller, the Brake roller or the document path dirty? YES Clean the scanner completely. (* 5) NO Continued on next page 5-22 5.2 Troubleshooting - Fujitsu fi-4860C | Operation Manual - Page 187
installed properly? nstall the Pick roller and the Brake roller properly. (* 6) YES Have you scanned many sheets? Check the consumables life to ensure you have not scanned more than 300,000 sheets. (* 7) YES NO Contact an authorized FUJITSU Scanner service provider. Replace the Pick roller - Fujitsu fi-4860C | Operation Manual - Page 188
documents satisfy the NO conditions described in "6.2 Document Quality," "Precautions"? Use documents which satisfy the requirements. (* 1) YES Is the length of the documents installed properly? NO Re-install the Pad ASSY properly. (* 4) YES Continued on next page 5-24 5.2 Troubleshooting - Fujitsu fi-4860C | Operation Manual - Page 189
Pick roller and the Brake roller properly. (* 6) YES Have you scanned many sheets? Check consumables life to ensure you have not scanned more than 300,000 pages. (* 7) YES Replace the Pick roller unit and the Brake roller unit if necessary. (*6) NO Contact an authorized FUJITSU Scanner service - Fujitsu fi-4860C | Operation Manual - Page 190
of the scanned image. Did you adjust the offset (position to start scanning the documents)? YES Contact an authorized FUJITSU Scanner service provider. NO Do the offset adjustment. Which OS are you using? Windows 98/ Windows Me/ Windows 2000/ Windows XP Windows 95/ Windows NT 4.0 Display - Fujitsu fi-4860C | Operation Manual - Page 191
the driver. (* 1) YES Is Adaptec EZ-SCSI installed ? YES Uninstall EZ-SCSI first, then install the driver. NO Is the Check LED on the operator panel lit? NO YES Contact an authorized FUJITSU Scanner service provider. Continued on next page SOLVING COMMON PROBLEMS 5 5.2 Troubleshooting 5-27 - Fujitsu fi-4860C | Operation Manual - Page 192
operator panel blinking? NO YES Check LCD display for error. Eliminate the cause of the error. (* 2) Contact an authorized FUJITSU Scanner service provider. (* 1) For the details on how to install FJTWAIN, refer to "FJTWAIN32 Scanner Driver (Scanner Utility for Microsoft Windows) User's Guide - Fujitsu fi-4860C | Operation Manual - Page 193
FUJITSU Scanner service provider. SOLVING COMMON PROBLEMS 5 (* ) For the details on how to install FJTWAIN, refer to "FJTWAIN32 Scanner Driver (Scanner Utility for Microsoft Windows) User's Guide", "3. Installation." The User's Guide is included in the FJTWAIN CD-ROM. 5.2 Troubleshooting - Fujitsu fi-4860C | Operation Manual - Page 194
Please check the following items before contacting an authorized FUJITSU Scanner service provider. ■ General descriptions Items to check Model Serial Number Manufacturing date Date of purchase Symptom Frequency of trouble (example) fi-4860C (example) 000001 (example) 2003-08 (August 2003) (example - Fujitsu fi-4860C | Operation Manual - Page 195
date Last consumable replacement date Operator panel status at trouble Findings (example) Copier paper (example) Filing company documents (example) December 2003 (example) November 15, 2003 (example) Paper Jam2 Imaging quality trouble Items to check Type and version of scanner driver Interface - Fujitsu fi-4860C | Operation Manual - Page 196
This section describes how to check the labels on the scanner. The positions of the labels The following shows where the two labels are located on the scanner. Manufacturing Label (example): Indicates scanner manufacturing information. Regulatory label (example): Shows the conforming standards of - Fujitsu fi-4860C | Operation Manual - Page 197
the sizes and qualities of documents required for the satisfactory performance of the scanner. 6.1 Document Size 6-2 6.2 Document Quality 6-3 6.3 Hole-punching Prohibited Areas 6-6 6.4 Print Prohibited Area 6-7 6.5 Background Color Areas 6-8 6.6 Job Separation Sheet 6-9 6.7 Hopper Capacity - Fujitsu fi-4860C | Operation Manual - Page 198
6.1 Document Size The following shows the supported document sizes. A Feeding Direction B A 297 mm 11.7 in. Maximum B 432 mm 17 in. A 74 mm 2.9 in. Minimum B 74 mm 2.9 in. 6-2 6.1 Document Size - Fujitsu fi-4860C | Operation Manual - Page 199
documents can be scanned. ■ Document thickness Paper thickness is expressed by "paper weight." The following shows the paper weights that can be used on this scanner: 52 g/m2 to 127 g/m2 or 14 lb to 34 lb (when fi-486TRK option is not installed) ADF DOCUMENT SPECIFICATIONS 6.2 Document Quality - Fujitsu fi-4860C | Operation Manual - Page 200
documents, set the density to light to HINT avoid a bleed through. − To prevent the rollers from becoming dirty, avoid scanning documents containing large areas written or filled in pencil. If scanning of such documents is inevitable, clean the rollers more frequently. 6-4 6.2 Document Quality - Fujitsu fi-4860C | Operation Manual - Page 201
. • When scanning wood containing paper, the service life of the Pad ASSY and the Pick roller may be shortened compared to the case of scanning woodfree paper. ADF DOCUMENT SPECIFICATIONS When using the ADF, the leading edge of all document sheets must be HINT evenly aligned. Make sure that - Fujitsu fi-4860C | Operation Manual - Page 202
requirements, please refer to the section "6.6 Job Separation Sheet" on page 6-9. Reading reference position 113 (4.45") 134 (5.28") 79 (3.12") 96 (3.78") 10 10 12 12 10 10 (0.39") (0.39") (0.47") (0.47") (0.39") (0.39") (Unit : mm) Top of document 15 (0.59") Front side Reading surface - Fujitsu fi-4860C | Operation Manual - Page 203
CONDITIONS" on page AP-2. 6 Center of document Reading reference position 113 (4.45") 134 (5.28") 79 (3.12") 96 (3.78") (Unit : mm) Top of document 15 Front side Reading surface : Area A : Area B Document feeding direction ADF DOCUMENT SPECIFICATIONS 10 10 (0.39")(0.39") 10 10 34 - Fujitsu fi-4860C | Operation Manual - Page 204
6.5 Background Color Areas Paper white detection is performed in the shaded area as shown in the Figure below. The top 3mm on both sides of a document, should have no printing in this area. When using dropout color, the color can be in this area. If this cannot be followed, turn the - Fujitsu fi-4860C | Operation Manual - Page 205
1. Shape The following shows the typical format of the job separation sheet. 15 (0.59") 6 Feeding direction 15 (0.59") ADF DOCUMENT SPECIFICATIONS Center of document more than 210 (8.27") (Unit : mm) 2. Document Specifications Document width must be Letter (8.5 inch)/A4 width (210mm) or wider - Fujitsu fi-4860C | Operation Manual - Page 206
be loaded on the Hopper depends on the paper size and the ream weight. This information is shown in the following graph. Capacity of Hopper (sheets) 500 A4/Letter or smaller Legal 300 200 250 A3 or 11x17 in. 150 110 52 80 128 Paper weight (g/m2 ) Paper weight g/m2 lb - Fujitsu fi-4860C | Operation Manual - Page 207
7 OPERATOR PANEL MENUS This chapter explains the setup mode and the test mode of the scanner. 7.1 Setup Mode 7-2 7.2 Setup mode functions 7-10 7.3 Setup Mode Details 7-17 7.4 Test Mode Overview 7-64 7.5 Test Mode Details 7-70 7-1 - Fujitsu fi-4860C | Operation Manual - Page 208
functions are different. To enter these modes, follow the instructions below: - Online setup mode When LCD indicates Ready status Enter button), the scanner enters Online setup mode. - Offline setup mode Press and hold (Start button) and turn on the power. The Operator panel LCD displays the - Fujitsu fi-4860C | Operation Manual - Page 209
, the scanner setup can be changed without turning off the power. However, the following items cannot be changed from this mode. - Consumables counter reset - SCSI ID change 7 - Product ID change - SCSI bus width change - Interface change - TPS interface baud rate change OPERATOR PANEL MENUS - Fujitsu fi-4860C | Operation Manual - Page 210
] Function Displays the next menu item without saving the change. Referred to as Next button in this manual. Displays the previous menu item without saving the change. Referred to as Previous button in this manual. Moves to the right item on the menu Referred to as Right arrow button in this - Fujitsu fi-4860C | Operation Manual - Page 211
10/ 15/ 20 mm ! 07 I PC Pr e- s e t = No / 1 / 2 / 3 / 4 / 5 ! 08 Ab r a s i on Al a r m Se t ? No / Y e s ! 08- 1 Al a r m Mo d e S t o p / Me s s a g e ! 08- 2 Al a r m CNT = 300000 sheet OPERATOR PANEL MENUS 7 7.1 Setup Mode 7-5 - Fujitsu fi-4860C | Operation Manual - Page 212
! 09 Abr as i on CNT Pi c k / Br a k e / Pad ! 09- 1 Pi c k CNT =xxxx xx Re s e t / No ! 09- 2 Br a k e CNT =xxxx xx Re s e t / No ! 09- 3 Pa d CNT =xxxx xx Re s e t / No ! 09- 4 Fr ont L a mp =xxxxxx Re s e t / No ! 09- 5 Bac k L a mp =xxxx xx Re s e t / No ! 09- 6 xxxx - Fujitsu fi-4860C | Operation Manual - Page 213
1. 0 Se c ! 18- 2 = T i me - o u t 30 Se c ! 20 Pr oduc t ID f i 4860C / f i 4990C ! 21 S CS I Bu s = Wi d t h 8/ 16 bi t ! 22 I nt er f t = On / Of f ! 25- 4 = Re s e t No w No / Ye s OPERATOR PANEL MENUS 7 7.1 Setup Mode 7-7 - Fujitsu fi-4860C | Operation Manual - Page 214
! 26 I nk( x xxx ) =g g g g c c Re s e t / No ! 27 Po we r = 10 15 Sa v e 2 0 mi n ! 28 Br i g h t n e s s Ch a n g e ? No / Ye s ! 29 I mp r i n t e r St at u s Pos t / Pr e ! 30 = No r L a mp c ont r ol ma l / A l wa y s On (To screen !1) ! 26- 1 Re s e t No / No w Yes ! - Fujitsu fi-4860C | Operation Manual - Page 215
board is HINT installed. Screen 24 appears only when both the fi-486PRFR (Front side imprinter) and the fi-486PRRE (Rear side imprinter) are installed. 7 Screen 25, Screen 26 and Screen 29 appear when either or both of the fi- 486PRFR and the fi-486PRRE are installed. OPERATOR PANEL MENUS - Fujitsu fi-4860C | Operation Manual - Page 216
in setup mode as shown in the following. LCD display Descriptions Double Feed Specifies the double-feed detection mode based on: 1: Document overlapping / thickness 2: Document overlapping / thickness+ Brake roller rotation amount Length Check Specifies the double-feed detection based on the - Fujitsu fi-4860C | Operation Manual - Page 217
The replacement timing increment/ decrement by 10,000 sheets. Abrasion Counter Clear the consumable counters (Abrasion counter) - Not Avail- - Avail- able able Manual Feed Specifies the pick start time from the time document is manually set. 0.2 to 29.8 sec 1.0 sec Avail- Avail- able - Fujitsu fi-4860C | Operation Manual - Page 218
display Descriptions Selectable parameters Skew Check Specifies if skew detection is On/Off enabled. Separation Specifies the Brake roller force Thick appropriate for the document thickness Medium Thick Default Mode Remarks On- Offline line Off Avail- Avail- Settings via the able able - Fujitsu fi-4860C | Operation Manual - Page 219
pick Enable or disable pre-pick operation, the picking of a document prior to actual feeding. (increase scan throughput) On / Off Picking speed Specify the Pick roller rotation Fast / speed Mid / Slow Pick retry Specify the Pick throughput able able of the scanner will be affected. Retry - Fujitsu fi-4860C | Operation Manual - Page 220
7 Product ID SCSI Bus Specifies the scanner product ID. fi4860C / fi4990C / M4099D / M3099G Specifies the SCSI data bus width, 8bit or 16 bit. 16bit/ 8bit Interface Specifies the interface to use Auto / when an optional or third party SCSI / interface board is installed in TPS the TPS (Third - Fujitsu fi-4860C | Operation Manual - Page 221
/ 2400 When both fi-486PRFR (Front Pre / Post side/Pre-print) and fi486PRRE (Rear side/Postprint) are installed, specifies which one to setup. When either fi-486PRFR (Front side/Pre Reset at hopper empty: On - Avail- Avail- - able able OPERATOR PANEL MENUS 7 7.2 Setup mode functions 7-15 - Fujitsu fi-4860C | Operation Manual - Page 222
the time before entering Power save mode. 5 to 60minutes Language Specifies the language to use for Operator panel display. Japanese (Katakana) / English Imprinter Status Shows the installed imprinter type. Lamp control Specifies whether or not to keep the lamp turned on. Normal/ AlwaysON - Fujitsu fi-4860C | Operation Manual - Page 223
button) and let the scanner show . ! 01 Se par at i on = Thi n Thi c k 7 2) At , press (Left arrow button) or (Right arrow button) and select the appropriate document thickness. The blinking item is the one selected. HINT OPERATOR PANEL MENUS (Right arrow - Fujitsu fi-4860C | Operation Manual - Page 224
, change the setting by HINT referring to the explanation on the table. - Double-feed - Mis-pick - Paper Jam1 Setting Document separation force Double-feed occurs frequently. Mis-pick or Paper jam1 occurs fre- quently. Thick Strong Medium Thick Medium strong Medium Average (Factory - Fujitsu fi-4860C | Operation Manual - Page 225
1) Press (Next button) or (Previous button) and let the scanner show . ! 02 = Pr e- p i c k On / Of f 2) At , to enable Pre-pick, press (Left arrow button) and select [On]. 7 To disable Pre-pick, press (Right arrow button) and select [Off]. 3) Press Press screen - Fujitsu fi-4860C | Operation Manual - Page 226
goes back to [Ready] Pick roller rotation speed should be set Slow for scanning thin or soft docu- HINT ments, these documents tend to cause a Mis-pick to occur. Picking speed Fast (Factory default) Mid Slow When Mis-pick occurs frequently Decreases the Pick speed When the Pick speed is set at - Fujitsu fi-4860C | Operation Manual - Page 227
to (3). By pressing (Left arrow button), the selection moves from (3) to (1). OPERATOR PANEL MENUS (1) [No] is blinking: Document overlapping and thickness are not checked. (2) [Yes] and [1] are blinking: Document overlapping and thickness are checked. However, the scanning continues even if - Fujitsu fi-4860C | Operation Manual - Page 228
the selection moves from (1) to (3). (Left arrow button), the selection moves from (3) to (1). (1) [Off] is blinking: Document overlapping is not checked. (2) [On] and [1] are blinking: Document overlapping is checked for the range set at step 4). This mode is used for preventing mis-detection - Fujitsu fi-4860C | Operation Manual - Page 229
by checking paper thickness. ! 04- 3 +Thi c k ness No / Ye s OPERATOR PANEL MENUS (1) [Yes] is blinking: (2) [No] is blinking: The Double-feed deteciton by ) is pressed, LCD displays [Thickness] and [Thickness & Roller] alternately. 7.3 Setup Mode Details 7-23 - Fujitsu fi-4860C | Operation Manual - Page 230
based on the light amount transmitted through paper and Brake roller rotation amount. Also the double-feed detection by checking paper (1) [Pick] is blinking: Double-feed is checked by the document pick timing. (2) [Pick & Feed] is blinking: Double-feed is checked by the document pick timing - Fujitsu fi-4860C | Operation Manual - Page 231
-feed is detected and the scanning operation is stopped, the last documents in the hopper or the one ahead of it might have been double fed. Depending on the document type, there are cases when double-feed can not be detected by paper thickness. 7 OPERATOR PANEL MENUS 7.3 Setup Mode Details 7-25 - Fujitsu fi-4860C | Operation Manual - Page 232
5. Setting Double-feed detection (by document length) 1) Press (Next button) or (Previous button) and let the scanner show . ! 05 Lengt h Ch e c by document length can be enabled or disabled. By checking the document length for partially over lapped sheets that are fed together - Fujitsu fi-4860C | Operation Manual - Page 233
OPERATOR PANEL MENUS 3) In case of (2) or (3), by pressing . (Enter button), LCD display changes to ! 05- 1 Lengt h = 10/ 15/ 20 mm 4) At , by pressing (Left arrow button) or (Right arrow button), 7 the document length can be specified. By pressing ( - Fujitsu fi-4860C | Operation Manual - Page 234
6. Setting Skew Check 1) Pressing (Next button) or . (Previous button) and let the LCD show ! 06 = Sk ew Ch e c k On / Of f 2) If you want to enable Skew check at , press (Left arrow button), and select [On]. To disable Skew-check, press (Right arrow button) and - Fujitsu fi-4860C | Operation Manual - Page 235
At , the preset items can be selected by pressing (Left arrow button) or (Right arrow button). The blinking item is the one selected. HINT OPERATOR PANEL MENUS 3) Press Press screen. (Enter button) to confirm the setting. (Exit button) at the end and the LCD display goes back to [Ready - Fujitsu fi-4860C | Operation Manual - Page 236
horizontal axis shows the darkness/color of the background against the text/lines on the documents. − The vertical axis shows the darkness of the text and lines on the documents. Document type and IPC preset pattern Background darkness Normal Dark Text Darkness Normal 1: Normal Background - Fujitsu fi-4860C | Operation Manual - Page 237
Line tion art/ Photos X - - X Halftone X DTC X Document sizes X - Portrait/ Landscape X - Cropping X - OPERATOR PANEL MENUS Document selection Gamma Pattern Valid X - Invalid - X Contrast X Auto separa- tion Reverse image Image empha sis Outline Extrac tion Simplified DTC - Fujitsu fi-4860C | Operation Manual - Page 238
) or . (Previous button) and let the LCD show ! 08 Al a r Abr as m Se t i on ? No / Ye s 2) At , to change Consumables replacement message setup (Abrasion Alarm), press (Right arrow button) and select [Yes]. The blinking item is the one selected. HINT Press LCD - Fujitsu fi-4860C | Operation Manual - Page 239
shown on the LCD but the scanning continues. OPERATOR PANEL MENUS By pressing (Enter button), appears on the LCD. ! 08- 2 Al a r m CNT = 300000 sheet 4) At , specify the number of scans to get Consumables replacement message. Each time (Left arrow button - Fujitsu fi-4860C | Operation Manual - Page 240
to reset. The blinking item is the one selected. HINT You can select a counter from the following. (1) [Pick] is blinking: Pick roller counter (Pick CNT) can be reset. (2) [Brake] is blinking: Brake roller counter (Brake CNT) can be reset. (3) [Pad] is blinking: Pad counter (Pad CNT) can be reset - Fujitsu fi-4860C | Operation Manual - Page 241
to , , , , or depending on the selection at . When [Pick] is selected: ! 09- 1 Pi c k CNT 7 =xxxx xx Re s e t / No OPERATOR PANEL MENUS When [Brake] is selected: ! 09- 2 Br a k e CNT =xxxx xx Re - Fujitsu fi-4860C | Operation Manual - Page 242
and press button). (Enter ! 09- 6 xxxx Re s e t No w No / Ye s [XXXXXX] is the counter value of the selected consumable. HINT − Pick roller counter − Brake roller counter − Pad counter − Front-side lamp counter (lamp-on time) − Back-side lamp counter (lamp-on time) 5) If you - Fujitsu fi-4860C | Operation Manual - Page 243
arrow button) or (Right arrow button) and select the proper setting for the document to scan. The blinking item is the one selected. HINT OPERATOR PANEL MENUS (1) [Normal] is blinking: This mode is for scanning documents longer than 80mm or 3.15inches. (2) [Short] is blinking: This mode is for - Fujitsu fi-4860C | Operation Manual - Page 244
11. Setting Language 1) Press (Next button) or . (Previous button) and let LCD display ! 11 Language =En g l i s h / 2) Press (Left arrow button) or (Right arrow button) and select the language for LCD display. 3) Press Press screen. (Enter button) to confirm the - Fujitsu fi-4860C | Operation Manual - Page 245
) and select [Black]. 3) Press Press screen. (Enter button) to confirm the setting. (Exit button) at the end and the LCD display goes back to [Ready] OPERATOR PANEL MENUS 7.3 Setup Mode Details 7-39 - Fujitsu fi-4860C | Operation Manual - Page 246
13. Setting Back-side background color 1) Press (Next button) or (Previous button) and let LCD display . ! 13 B. Ba c k g r o u n d = Wh i t e / B l a c k 2) At , to set the background color to white, press (Left arrow button) and select [White]. To set the - Fujitsu fi-4860C | Operation Manual - Page 247
OPERATOR PANEL MENUS 14. Setting Front-side dropout color 1) Press (Next button) or . (Previous button) and let LCD display ! 14 F . Dr o p - o u t = R/ G/ B 7 2) At , press ( - Fujitsu fi-4860C | Operation Manual - Page 248
15. Setting Back-side dropout color 1) Press (Next button) or . (Previous button) and let LCD display ! 15 = R/ B. G/ Dr B op- out 2) At , press (Left arrow button) or (Right arrow button) and select a color to drop out. The blinking item is the one - Fujitsu fi-4860C | Operation Manual - Page 249
) or . (Previous button) and let LCD display ! 16 Pi c k Ch a n g e ? r et r y No / Ye s 7 2) At , to change pick motor's pick operation time and the number of retries, press (Right arrow button) and select [Yes]. Press (Enter button) to confirm the selection - Fujitsu fi-4860C | Operation Manual - Page 250
(Right arrow button), the number of retries increases. Press (Left arrow button) or (Right arrow button), and select the setting. The number of the pick retries can be set between 1 to 7 times. 5) Press Press screen. (Enter button) to confirm the setting. (Exit button) again and the LCD display - Fujitsu fi-4860C | Operation Manual - Page 251
or . (Previous button) and let LCD display ! 17 Feed Ch a n g e ? r et r y No / Ye s 7 2) At , to change Feed motor operation time and the number of retries, press (Right arrow button) and select [Yes]. Press (Enter button) to confirm the selection. - Fujitsu fi-4860C | Operation Manual - Page 252
4) In , specify the number of retries. By pressing (Left arrow button), the number of retry decreases. By pressing (Right arrow button), the number of retries increases. The number of the feed retries can be set between 1 to 7 times. Press (Left arrow button) or (Right arrow button), and - Fujitsu fi-4860C | Operation Manual - Page 253
The blinking item is the one selected. HINT OPERATOR PANEL MENUS Press (Enter button) to confirm the pick from the manual setting of the document (Start time). By pressing (Left arrow button), the pick start time decreases. By pressing (Right arrow button), the pick start time increases. The pick - Fujitsu fi-4860C | Operation Manual - Page 254
me - o u t 30 Se c 4) At , specify the wait time (i.e. the time from the PC issues scan command to time out) for manual setting of document. By pressing (Left arrow button), the wait time becomes shorter. By pressing (Right arrow button), the wait time becomes longer. . The wait time - Fujitsu fi-4860C | Operation Manual - Page 255
2) At , press (Left arrow button) or press (Right arrow button) to select SCSI ID number. The blinking item is the one selected. HINT OPERATOR PANEL MENUS 3) Press Press screen. (Enter button) and make the setting valid. (Exit button) at the end and the LCD display goes back to [Ready - Fujitsu fi-4860C | Operation Manual - Page 256
20. Setting of Product ID(Scanner model number) 1) Press (Next button) or . (Previous button) and let LCD display ! 20 Pr oduc t f i 4860C /fi ID 4990C 2) At , press (Left arrow button) or (right arrow button) and select Product ID. The blinking item is the - Fujitsu fi-4860C | Operation Manual - Page 257
button) and select [16]. If SCSI-2 (50pin) interface is used, press (Left arrow button) and select [8]. The blinking item is the one selected. HINT OPERATOR PANEL MENUS 3) Press Press screen. (Enter button) to confirm the setting. (Exit button) at the end and the LCD display goes back to [Ready - Fujitsu fi-4860C | Operation Manual - Page 258
the one selected. HINT Available interface settings are as follows: (1) [Auto] is blinking: If an interface board, either from third party or optional, is installed in TPS, this interface is used. If not, SCSI interface is used. (2) [SCSI] is blinking: SCSI interface is used. The interface on TPS - Fujitsu fi-4860C | Operation Manual - Page 259
7 2) At , press (Left arrow button) or (right arrow button) and select Baud rate. The blinking item is the one selected. HINT OPERATOR PANEL MENUS Baud rates available are as follows: (1) 19200 bps (2) 9600 bps (3) 4800 bps (4) 2400 bps By pressing By pressing (Left arrow button - Fujitsu fi-4860C | Operation Manual - Page 260
confirm the setting. (Exit button) at the end and the LCD display goes back to [Ready] ATTENTION This screen is displayed only when both of fi-486PRFR and fi-486PRRE are installed. 7-54 7.3 Setup Mode Details - Fujitsu fi-4860C | Operation Manual - Page 261
N u mb e r i n g On / Of f ( x x x x ) 7 To show your selection of imprinter or the imprinter to setup, [Pre] or [Post] HINT is displayed. OPERATOR PANEL MENUS 2) At , to enable numbering printing with the imprinter, press (Left arrow button) and select [On]. Press (Enter button) to - Fujitsu fi-4860C | Operation Manual - Page 262
3) At , press (Left arrow button) or let your choice of number of digits blink. Selectable number of digits is listed as below. (Right arrow button) and (1) [5] is blinking: 5 digit (2) [8] is blinking: 8 digit Press (Enter button), then is displayed. ! 25 - Fujitsu fi-4860C | Operation Manual - Page 263
OPERATOR PANEL MENUS 5) At , you can specify if the numbering should be initialized to the specified initial value in 4) the LCD display goes back to [Ready] screen. ATTENTION Command from the PC takes the priority over the setting from the Operator panel. 7.3 Setup Mode Details 7-57 - Fujitsu fi-4860C | Operation Manual - Page 264
error occurs, be sure to reset the Ink remain counter. Pr e pa r e new I nk No w Re a d i n g ! x x x x [XXXX] is the scanned sheet counter value. HINT 1) Press (Next button) or . (Previous button) and let LCD display ! 26 = I nk( xxxx ) Re s e t / No Approximate - Fujitsu fi-4860C | Operation Manual - Page 265
Screen26-1> is displayed. Not to reset, select [No] and press (Enter button). (Left arrow ! 26- 1 Re s e t No w 7 No / Ye s OPERATOR PANEL MENUS 3) At , to actually reset the counter, press (Right arrow button) and select [yes]. To cancel the reset, select [No] and - Fujitsu fi-4860C | Operation Manual - Page 266
Enter button). ! 27- 1 = 10 T i me 15 2 0 mi n 3) At ,by pressing (Left arrow button) or (Right arrow button), select the scanner wait idle time before entering power save mode. The blinking item is the one selected. HINT A minimum of 5 minutes to the maximum of 60 - Fujitsu fi-4860C | Operation Manual - Page 267
is displayed. If Brightness adjustment is not required, select [No] and press button). (Enter ! 28- 1 Fr ont : Br i 0 ght ness Ba c k : 0 OPERATOR PANEL MENUS The blinking item is the one selected. HINT 3) At , to adjust the front-side brightness, press (Left arrow - Fujitsu fi-4860C | Operation Manual - Page 268
> ! 29 I mp r i n t e r St at u s Pos t / Pr e [XXXX/XXXX], imprinter installation status is displayed as follows. (1) Only fi-486PRFR is installed: (2) Only fi-486PRRE is installed: (3) Both fi-486PRFR and fi-486PRRE are installed: [Pre] [Post] [Post/Pre] 2) By pressing (Exit button), LCD - Fujitsu fi-4860C | Operation Manual - Page 269
blinking: [Normal] mode is selected. [AlwaysOn] mode is selected. The lamp is kept turned on. 3) By pressing (Exit button), LCD display goes back to "Ready". OPERATOR PANEL MENUS 7.3 Setup Mode Details 7-63 - Fujitsu fi-4860C | Operation Manual - Page 270
pressing (Start button) and turn on the power. Then the Operator panel LCD displays the following message. < MOD E SEL ECT> SET UP TEST Press (Left arrow button) or (Right arrow button) and select [TEST]. By pressing (Enter button), the scanner enters test mode. To end the test mode, turn off - Fujitsu fi-4860C | Operation Manual - Page 271
the change and then displays the next menu item Referred to as Enter button in this manual. Moves to the upper level menu item without saving the change. Referred to as Exit button in this manual. 7 OPERATOR PANEL MENUS ■ Transition of screens in test mode Refer to the next page. The LCD screen - Fujitsu fi-4860C | Operation Manual - Page 272
T01 Si n g l e f eed S A4 P ST ART BW 2 00 Se t u p S A 4 eP t BW 2 00 Continue to screen T02 on the next page (Scanning) Start scanning, or setup imprinter test conditions R E S O L U T I Oe Nt 200 Re a d i n g M oe dt e COL OR P AP ER A4 S Ie Zt E P S I MP L E X e/ tD U P L E - Fujitsu fi-4860C | Operation Manual - Page 273
OPERATOR PANEL MENUS T02 Mu l t i f eed S A4 P ST ART BW 2 00 Se t u p S A 4 Pe t BW 2 00 Continue to screen T03 on the next page (Scanning) Start scanning, - Fujitsu fi-4860C | Operation Manual - Page 274
T03 De v i c e Li f e L A MP FO :f xf sx ex xt x x x x B: x x x x x x x x T04 Op t i o n s Pos t pO rf fi sn et et r : - Pr e pr i nt er : g 7-68 7.4 Test Mode Overview - Fujitsu fi-4860C | Operation Manual - Page 275
Single feed Multi feed Device Life Options Descriptions Scans a sheet of document without connecting to a PC. Scans documents continuously without connecting to a PC. Shows the cumulative lamp-on time. Shows the options installation status. 7 OPERATOR PANEL MENUS 7.4 Test Mode Overview 7-69 - Fujitsu fi-4860C | Operation Manual - Page 276
Single feed Without connecting to a PC, the scanner's whole mechanism's operation can be checked. Only one sheet is fed with this test. Scan parameters can be changed for scan test. Imprinter test print can be performed at the same time. 1) Place the documents to scan on the hopper. 2) Press (Next - Fujitsu fi-4860C | Operation Manual - Page 277
arrow button) or (Right arrow button) and select simplex or duplex. Press (Enter button) and confirm the setting. Then the display or (Right arrow button) and select the document size and the orientation. Following parameters can be specified. OPERATOR PANEL MENUS A4 portrait B4 portrait Legal - Fujitsu fi-4860C | Operation Manual - Page 278
back to . At , select [START], and press (Start button). If fi-486PRFR and/or fi-486PRREis installed, is displayed for setting imprinter test conditions. If an imprinter(s) is not installed, the scanner starts scanning operations. 7-72 7.5 Test Mode Details - Fujitsu fi-4860C | Operation Manual - Page 279
. Then select the imprinter to use. 7 If the printer to use is fi-486PRFR, select [Pre]. If fi-486PRRE, select [Post]. If imprinter test is not required, select [Off]. 7) Press (Start button). Scanning operation starts with or without imprinter test. To quit the test, press (Stop button - Fujitsu fi-4860C | Operation Manual - Page 280
Without connecting to a PC, the scanner's whole mechanism's operation can be checked. In this test documents are scanned continuously. Scan parameters can be changed for scanning test. Imprinter test print can be performed at the same time. 1) Place the documents to scan on the hopper. 2) Press - Fujitsu fi-4860C | Operation Manual - Page 281
button) and select simplex or duplex. Press (Enter button) and confirm the setting. Then the display goes back to . OPERATOR PANEL MENUS (2) At , (Right arrow button) and select the document size and the orientation. Following parameters can be specified. 7.5 Test Mode - Fujitsu fi-4860C | Operation Manual - Page 282
A4 portrait B4 portrait Legal portrait 11 x 17 inch portrait A3 portrait A5 landscape B5 landscape Letter landscape A4 landscape A5 portrait B5 portrait Letter portrait A4P B4P LGP DLP A3P A5L B5L LTL A4L A5P B5P LTP Press (Enter button) and confirm the setting.Then is redisplayed. - Fujitsu fi-4860C | Operation Manual - Page 283
-1>, select [START] and press (Start button). If fi-486PRFR and/or fi-486PRREis installed, is displayed for setting imprinter test conditions. If an imprinter(s) is not installed, the scanner starts scanning operations. Pr i n t = Of f / On : P r e / Po s t 6) At this - Fujitsu fi-4860C | Operation Manual - Page 284
7) Press (Start button). Scanning operation starts with or without imprinter test. To quit the test, press (Stop button). HINT The LCD goes back to . 7-78 7.5 Test Mode Details - Fujitsu fi-4860C | Operation Manual - Page 285
number of lamp-on time. 1) Press (Next button) or (Previous button) and let LCD display . T03 De v i c e Li f e 7 OPERATOR PANEL MENUS 2) At , press (Start button) or is displayed. (Enter button). Then L A MP FO f: xf sx ex xt - Fujitsu fi-4860C | Operation Manual - Page 286
t pO fr if ns et et r : - Pr e pr i nt er : If fi-486PRFR is installed, LCD display shows [Pre Printer: ]. [ ] indicates that the printer is installed. If not installed, it shows [Pre Printer:-]. If fi-486PRRE is installed, LCD display shows [Post Printer: ]. [ ] indicates that the printer is - Fujitsu fi-4860C | Operation Manual - Page 287
8 OPTIONS This chapter describes options for fi-4860C. 8.1 Options 8-2 8.2 fi-486PRFR (Front side imprinter 8-3 8.3 fi-486PRRE (Rear side imprinter 8-4 8.4 fi-486TRK (Thinner paper Roller Kit 8-5 8-1 - Fujitsu fi-4860C | Operation Manual - Page 288
Options The following lists options available for the scanner. Name fi-486PRFR fi-486PRRE fi-486TRK Part No. PA03296-D207 PA03296-D200 PA03296-D780 Description Prints information on the front of a document prior to scan. Installed before the scanner optics. Imprinted data is captured during scan - Fujitsu fi-4860C | Operation Manual - Page 289
(Front side imprinter) OPTIONS Center of document Document feeding direction fi-486PRFR is installed at the front side of the document path, inside of the scanner. It prints prior to scanning. fi-486PRFR (Front side imprinter) Specifications are described below. Item Printing Method Printable - Fujitsu fi-4860C | Operation Manual - Page 290
E Printing Area (Back) D Center of document Document feeding direction Consumables Print Cartridge C A B As for the operations and functions of fi-486PRRE (Rear side imprinter), refer to the fi-486PRRE Operator's Guide attached to fi-486PRRE. 8-4 8.3 fi-486PRRE (Rear side imprinter) - Fujitsu fi-4860C | Operation Manual - Page 291
,000 sheets or 1 year When using fi-486TRK, documents of coated paper (e.g. photos, maga- HINT zines, etc.) may not be fed into the ADF successfully. For scanning such documents, the standard pick roller unit and the brake roler unit are recom- mended. 8.4 fi-486TRK (Thinner paper Roller Kit - Fujitsu fi-4860C | Operation Manual - Page 292
8-6 8.4 fi-486TRK (Thinner paper Roller Kit) - Fujitsu fi-4860C | Operation Manual - Page 293
9 SCANNER SPECIFICATIONS This chapter describes the Scanner Specifications. 9.1 Basic Product Specifications 9-2 9.2 Installation Specifications 9-3 9.3 Dimensions 9-5 9-1 - Fujitsu fi-4860C | Operation Manual - Page 294
Specifications 1 Scanner Type ADF(Automatic Document Feeder) and Manual feed 2 Image sensor Color CCD x 2 Front/Back 3 Light source White fluorescent lamp x 2 Front/Back 4 Scanning area Minimum 74 mm x 74 mm, 2.9 in. x 2.9 in. - Maximum A3 or 11x17 in. - 5 Document thickness - Fujitsu fi-4860C | Operation Manual - Page 295
. Height 523 mm, 20.6 in. 100 mm 4 in. Scanner 100 mm 4 in. 600 mm 23.6 in. Weight (kg) Input power Voltage Phase Frequency Power consumption Front 45 kg, 99 lb AC100 - 240 V±10 % Single-phase 50/60 Hz +2/-4 % 200 W or less SCANNER SPECIFICATIONS 9 9.2 Installation Specifications 9-3 - Fujitsu fi-4860C | Operation Manual - Page 296
Item Ambient condition Device status Temperature Humidity Heat capacity Shipping Weight (kg) Specification Operating Not operating 15 -- 35 degrees Celsius 59 -- 95 degrees Fahrenheit -20 -- +60 degrees Celsius -4 -- +140 degrees Fahrenheit 20 - 80 % 8 - 95 % 172 kcal or less 50 kg, 110 - Fujitsu fi-4860C | Operation Manual - Page 297
9.3 Dimensions 523 (20.6 in.) (17in) (20.5 in.) 520 (20.5 in.) (20.6 in.) unit: mm 9-5 9.3 Dimensions - Fujitsu fi-4860C | Operation Manual - Page 298
9-6 9.3 Dimensions - Fujitsu fi-4860C | Operation Manual - Page 299
APPENDIX1 DROP-OUT COLOR A drop-out color is a color that can be eliminated from what the scanner sees. To check the background color of document for drop-out, use the method and follow the standards given below. Print density measurement The measurement must be made in one of the following - Fujitsu fi-4860C | Operation Manual - Page 300
of these detection modes. (When fi-486TRK is not installed.) Detection by Document Overlapping - Paper weight: 52 g/m2 - 127 g/m2 or 14 lbs to 34 lbs - Punched holes are not allowed within 35mm (1.4 inch) of the vertical center line of the document. Detection by Document Thickness Sheets of the same - Fujitsu fi-4860C | Operation Manual - Page 301
. - The deviation in the amount of the light transmitted through background areas must not be less than 10%. Detection by Document Overlapping, Thickness and Length Sheets of the same thickness and length shall be set in the ADF at a time. - Paper weight: 52 g/m2 - 127 g/m2 or 14 lbs to 34 - Fujitsu fi-4860C | Operation Manual - Page 302
areas must not be less than 10%. The type and the conditions of document and the conditions sometimes HINT cause the double-feed detection rate to drop. When the overlapping check is specified, the paper sheets which contact HINT closely each other, such as electro-statically charged paper - Fujitsu fi-4860C | Operation Manual - Page 303
APPENDIX3 MESSAGES OF OPERATOR PANEL ■ Massages of Scaner Operation Status changes to with progress of time, and when all become , it (Initializing) move to the following check states. (Ejecting document) (Checking sensor) - Fujitsu fi-4860C | Operation Manual - Page 304
panel disappears and the Power LED lamp lights, the scanner is in the Low power mode. ATTENTION The scanner wakes up from Low power mode by one of the following operations. Press any button (except Power button) on the Operator Panel. Set the documents on the Hopper. Send the command from PC - Fujitsu fi-4860C | Operation Manual - Page 305
) shows the value of Abrasion counter or the value of Life counter. (Scanning) The following message is displayed while the scanner is scanning continuously in the state where double feed has been detected (by thickness check). If a double feed detection state is canceled on - Fujitsu fi-4860C | Operation Manual - Page 306
"xxxx" shows the number of Batch counter value. HINT (Waiting) HINT The following message is displayed while the scanner is waiting in the state when double feed (check thickness) has been detected. Press the [Stop] button, and the double feed detection state is canceled. - Fujitsu fi-4860C | Operation Manual - Page 307
of Batch counter value. HINT The following message displayed if a document is jammed in the ADF. Refer to "5.1 Clearing Document Jams" on page 5-2 for removing the document remained in the scanner. Pa pe r J a mx One of "1" - "8" is displayed instead of "x", depending on paper - Fujitsu fi-4860C | Operation Manual - Page 308
. Do u b l e Feed (by length check) The following message is displayed, when the double feed is detected by length check. Lengt h er r or The following message is displayed, when a document is not sent from the hopper to the ADF. Mi s - p i c k Check LED does not blink at Mis - Fujitsu fi-4860C | Operation Manual - Page 309
is displayed, When skewed document is fed from the hopper to the ADF. I r r egul ar paper not set correctly or when there are too many documents. (When the documents are on the hopper.) Ho - Fujitsu fi-4860C | Operation Manual - Page 310
, when the Separation roller rotates while the Brake roller does not rotate at all. Sep ar at i on r ol l er wo r n value exceeds the setting value to display an consumables replacement message. Ab - Fujitsu fi-4860C | Operation Manual - Page 311
, please contact a distributor or an nearest imaging service and support center for help. (Front messages are displayed, when the fuse of various (Toransport motor) motors (Toransport motor, Separation motor, Pick motor, Hopper motor) goes out. Fus e Feed al ar m mo t o r ( - Fujitsu fi-4860C | Operation Manual - Page 312
(Front side) The following message is displayed, when the fuse for the lamp for front side blows out. Fus e al ar m Fr o nt si de l a mp The following message is displayed, when the fuse for the lamp (Back side) for back side blows out. Fus e al ar m - Fujitsu fi-4860C | Operation Manual - Page 313
occurs x x x x Se n s o r er r or "xxxx." shows the sensor name (SUS, SF0, SA4, etc.) The following message is displayed, when the temperature inside the scanner becomes higher than normal. T e mp e r a t u r e al ar m ● AP-15 - Fujitsu fi-4860C | Operation Manual - Page 314
The following message is displayed, when an error occurs in the Power supply. P o we r suppl y er r or The following message is displayed, when an error occurs in the EEPROM. A DDR ES S xxH E E P ROM Al a r m The EEPROM address where the error occurs is - Fujitsu fi-4860C | Operation Manual - Page 315
MD C d o wn l o ad Er r o r The following message is displayed, when an error occurs in the fi-486PRFR (Imprinter of front-side) or the fi-486PRRE (Imprinter of rear-side). Pr e I mp r i n t e r Al a r m Pos t I mp r i n t e r Al a r m The following message - Fujitsu fi-4860C | Operation Manual - Page 316
● AP-18 - Fujitsu fi-4860C | Operation Manual - Page 317
Save.........1-5 Basic Scanner Operations 1-1 Batch counter 4-3 Brake roller 3-3, 3-14 Brake roller unit 4-12 C Cleaner F1 3-2 Cleaner F2 3-2, 3-19 Cleaning Brake roller 3-14 Cleaning sheet 3-8 Discharge brush 3-24 Document width sensor........3-35 Feed roller 3-18 Glass sheet guide 3-32 - Fujitsu fi-4860C | Operation Manual - Page 318
on 1-2 Power Save Mode 1-5 R Removable sheet guide ........3-3, 3-29 Replacing Back-side lamp 4-20 Brake roller unit 4-12 Front-side lamp 4-15 Pad ASSY 4-4 Pick roller unit 4-9 S ScandAll 21 1-23, 1-26 Scanner Specifications 9-1 Scanning documents 1-23 Different-size 2-2 Dropout 2-13 PDF - Fujitsu fi-4860C | Operation Manual - Page 319
Service provider 5-30 Setting Window for FUJITSU TWAIN32 Scanner Driver 1-31 Setup mode 1-10, 7-2 Details 7-17 Function of buttons 7-4 Outline 7-2 Transitions, screens 7-4 SF0 sensor 3-3, 3-37 SF1 sensor 3-3, 3-37 SF1.5 sensor 3-3, 3-39 SF2 sensor 3-3, 3-39 Side cover 3-47 Side guides - Fujitsu fi-4860C | Operation Manual - Page 320
● IN-4 - Fujitsu fi-4860C | Operation Manual - Page 321
fi-4860C Image Scanner Operator's Guide P3PC-E167-04EN Date published: August, 2003 PFU LIMITED •Copying of the contents of this manual in whole or in part and copying of the scanner application is forbidden under the copyright law. •The contents of this manual are subject to change without notice.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
-
315
-
316
-
317
-
318
-
319
-
320
-
321
 |
 |
Operator's Guide
fi-4860C
Image Scanner
P3PC-E167-04EN