Garmin GCV 10 Installation Instructions
Garmin GCV 10 Manual
 |
View all Garmin GCV 10 manuals
Add to My Manuals
Save this manual to your list of manuals |
Garmin GCV 10 manual content summary:
- Garmin GCV 10 | Installation Instructions - Page 1
to avoid damage to your boat, install the Garmin® GCV 10 device according to these instructions. Read all installation instructions before proceeding with the installation. If you experience difficulty during the installation, contact Garmin Product Support. Registering Your Device Help us better - Garmin GCV 10 | Installation Instructions - Page 2
transducer cables. Installation Diagram You can use this diagram to identify the connection points from your sounder to the network, power, and transducer. Item À Á Â Ã Description Chartplotter GCV 10 Power Source Transducer Garmin dealer or directly from Garmin at www.garmin.com. Installing - Garmin GCV 10 | Installation Instructions - Page 3
- Garmin GCV 10 | Installation Instructions - Page 4
logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GCV™ is a trademark of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. © 10/08/2013 Garmin Ltd. or its subsidiaries www.garmin.com/support
-
1 -
2 -
3 -
4
 |
 |
GCV™ 10 Installation Instructions
To obtain the best performance and to avoid damage to your
boat, install the Garmin
®
GCV 10 device according to these
instructions.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation,
contact Garmin Product Support.
Registering Your Device
Help us better support you by completing our online registration
today.
•
Go to
.
•
Keep the original sales receipt, or a photocopy, in a safe
place.
Contacting Garmin Product Support
•
Go to
www.garmin.com/support
and click
Contact Support
for in-country support information.
•
In the USA, call (913) 397.8200 or (800) 800.1020.
•
In the UK, call 0808 2380000.
•
In Europe, call +44 (0) 870.8501241.
Important Safety Information
WARNING
See the
Important Safety and Product Information
guide in the
product box for product warnings and other important
information.
You are responsible for the safe and prudent operation of your
vessel. Sonar is a tool that will enhance your awareness of the
water beneath your boat. It does not relieve you of the
responsibility of observing the water around your boat as you
navigate.
CAUTION
Failure to install and maintain this equipment in accordance with
these instructions could result in damage or injury.
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
Installation Preparation
NOTICE
This device must be installed according to these instructions to
get the best possible performance. If you experience difficulty
with the installation, contact Garmin Product Support.
Because every boat is different, you must carefully plan the
GCV 10 sounder installation.
1
Select a mounting location.
2
Mount the sounder.
3
Connect the sounder to the Garmin Marine Network and to
power.
4
Connect the sounder to the transducer.
Tools Needed
•
Drill and drill bits
•
#2 Phillips screwdriver
•
Cable ties (optional)
•
Marine sealant (optional)
Mounting the Sounder
Mounting Location Considerations
•
The sounder must be mounted in a location where it cannot
be submerged.
•
The sounder must be mounted in a location with adequate
ventilation where it will not be exposed to extreme
temperatures.
•
The sounder should be mounted so that the LEDs are
visible.
•
The sounder should be mounted so that the power and
network cables can be easily connected.
•
The sounder should be mounted so that the transducer cable
can be connected. If required, transducer extension cables
are available through your Garmin dealer.
Mounting the Device
NOTICE
If you are mounting the bracket on fiberglass with screws, it is
recommended to use a countersink bit to drill a clearance
counterbore through only the top gel-coat layer. This will help to
avoid any cracking in the gel-coat layer when the screws are
tightened.
Stainless-steel screws may bind when screwed into fiberglass
and overtightened. Garmin recommends applying an anti-seize
lubricant to the screws before installing them.
Before you mount the device, you must select a mounting
location and determine the mounting hardware needed for the
surface.
NOTE:
Mounting hardware is included with the device, but it
may not be suitable for the mounting surface.
1
Place the device in the mounting location and mark the
location of the pilot holes.
2
Drill the appropriate pilot hole for one corner of the device.
3
Loosely fasten the device to the mounting surface with one
corner and examine the other three pilot-hole marks.
4
Mark new pilot-hole locations if necessary, and remove the
device from the mounting surface.
5
Drill the appropriate pilot holes for the other three marks.
6
Secure the device to the mounting location.
Connecting the Sounder
WARNING
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place will void the product warranty.
NOTICE
Do not force a cable into its port. Forcing the cable can damage
the pins. If the cable is properly aligned, the cable should
connect easily.
Before you connect the sounder to the network, power, and the
transducer, you must mount the sounder.
1
Route the cables using the appropriate tie wraps, fasteners,
and sealant to secure the cables along the route and through
any bulkheads or the deck (
page 2
).
November 2013
190-01663-02_0A
Printed in Taiwan