Garmin GHP 10V Marine Autopilot System S/N 19Y000000-19Y999999 GHP 10V Install
Garmin GHP 10V Marine Autopilot System Manual
 |
View all Garmin GHP 10V Marine Autopilot System manuals
Add to My Manuals
Save this manual to your list of manuals |
Garmin GHP 10V Marine Autopilot System manual content summary:
- Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 1
instructions. Read all installation instructions before proceeding with the installation. If you experience difficulty during the installation, contact Garmin Product Support be prepared to promptly regain manual control of your boat. • Safety and Product Information guide in the product box for - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 2
cable to a NMEA 2000 network. Garmin replacement part number: 010-11351-00 Caution: Do not connect this cable to a NMEA 2000 network. GHP 10V Installation Instructions - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 3
CCU. If the provided screws are not appropriate for the mounting surface, you will need to provide the correct types of screws. GHP 10V Installation Instructions - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 4
dedicated NMEA 2000 communication ports. If you do not have a NMEA 2000 network on your boat, the equipment necessary to build one is provided. For instructions on setting up the NMEA 2000 network, see page 11. • You can connect an optional NMEA 2000-compatible GPS device to the NMEA 2000 network - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 5
Red (+) Black (-) 8-32 Vdc 1 A fuse Orange(+) White (+) Alarm buzzer Blue (-) Black (-) Yellow CCU signal wire (see page 9) GHP 10V General Wiring Diagram GHP 10V Installation Instructions - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 6
your heading. 5. Hand-tighten the thumbscrew until the CCU is held firmly in the bracket. Do not overtighten the thumbscrew. Thumbscrew Cables GHP 10V Installation Instructions - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 7
Buzzer Wire Color White (+) Black (-) CCU cable Wire Color Orange (+) Blue (-) 3. Solder and cover all bare-wire connections. Alarm Buzzer Wiring Table GHP 10V Installation Instructions - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 8
operate your vessel. • Allows easy access to the keypad on the GHC 10. • Is strong enough to support the weight of the GHC 10 and protect it from excessive vibration or shock. • Allows room for the routing 9. Snap the mounting covers into place to install them. GHP 10V Installation Instructions - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 9
2000 network to use waypoint and route information with the GHP 10V. For more information on NMEA 2000, visit www.garmin.com. GHP 10V Installation Instructions - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 10
CCU with the yellow CCU signal wire in the GHC 10 power/data cable. • To add additional sensors to your NMEA 2000 network, follow the instructions included with the sensors. 10 GHP 10V Installation - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 11
terminator Creating a Basic NMEA 2000 Network for the GHC 10 and the CCU Notes: • To add additional sensors to your NMEA 2000 network, follow the instructions included with the sensors. • The GHC 10 is not powered by the NMEA 2000 network. It must be separately connected to the power source. • The - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 12
) for the optional GPS device you want to add to the NMEA 2000 network. 2. Connect the GPS device to the T-connector by following the instructions provided with the GPS device. To connect an optional NMEA 0183-compatible GPS device to your GHP 10V: 1. Determine the NMEA 0183 wiring assignments of - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 13
begin the compass calibration procedure, drive your boat in a slow, straight line, and wait for the wake generated by the previous step to pass. When instructed, turn the boat slowly clockwise, taking care to make as steady and flat a turn as possible. Turn slowly enough that the boat DOES NOT list - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 14
the heading when turning, you can make slight adjustments to the rudder gain. Note: When you manually adjust the rudder gain (or counter gain), make small adjustments, and adjust only one value at Configuration > Turn Fine Tuning Setup > Acceleration Limiter. 14 GHP 10V Installation Instructions - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 15
quickly define all of the important configuration settings on the GHP 10V. If, after running the wizard and manually adjusting the gains, you do not feel as though the GHP 10V is working correctly, you can run or decrease to fine-tune the autopilot heading. GHP 10V Installation Instructions 15 - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 16
Drive, adjusting the sensitivity of the Shadow Drive, and adjusting the Sea State Filtering setting. See the configuration section of the GHC 10 Quick Start Manual for more information. 16 GHP 10V Installation Instructions - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 17
source: 8-32 Vdc Fuse: AGC/3AG - 1 A GMI 10 power usage: 2.5 W max NMEA 2000 Power Input: 9-16 Vdc NMEA 2000 LEN: 2 (100 mA) GHP 10V Installation Instructions 17 - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 18
the following NMEA 0183 sentences: Receive-wpl, gga, grme, gsa, gsv, rmc, bod, bwc, dtm, gll, rmb, and xte. Transmit-hdg. 18 GHP 10V Installation Instructions - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 19
and use it to assist with the GHC 10 installation process. Read all installation instructions before installing the GHC 10. Contact Garmin Product Support if you have any questions during the installation process. 1. Refer to the diagram and notes starting on page 5 to understand the necessary - Garmin GHP 10V Marine Autopilot System | S/N 19Y000000-19Y999999 GHP 10V Install - Page 20
must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited. Information in this document is subject to change without notice. Garmin reserves the right to change or improve
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
GHP
™
10V Installation Instructions
To obtain the best possible performance and to avoid damage to your boat, install your GHP 10V marine autopilot system according to the
following instructions.
Read all installation instructions before proceeding with the installation.
If you experience difficulty during the
installation, contact Garmin Product Support or seek the advice of a professional installer.
The GHP 10V is compatible with C3 or newer Volvo
®
EVC systems. Contact Volvo for information on updating older EVC systems.
Product Registration
Help us better support you by completing our online registration today! Connect to our Web site at
. Keep the original
sales receipt, or a photocopy, in a safe place.
For future reference, write the serial number assigned to each component of your GHP 10V system in the spaces provided on
page 2
. The serial
numbers are located on a sticker on each component.
Contact Garmin
Contact Garmin Product Support if you have any questions while installing or using your GHP 10V autopilot system. In the USA, go to
www.garmin.com/support
, or contact Garmin USA by phone at (913) 397.8200 or (800) 800.1020.
In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.
In Europe, go to
www.garmin.com/support
and click
Contact Support
for in-country support information, or contact Garmin (Europe) Ltd. by
phone at +44 (0) 870.8501241.
Warnings
You are responsible for the safe and prudent operation of your vessel.
The GHP 10V is a tool that will enhance your capability to
operate your boat. It does not relieve you from the responsibility of safely operating your boat. Avoid navigational hazards and never leave
the helm unattended.
Always be prepared to promptly regain manual control of your boat.
Learn to operate the GHP 10V on calm and hazard-free open water.
Use caution when operating the GHP 10V at high speeds near hazards in the water, such as docks, pilings, and other boats.
See the
Important Safety and Product Information
guide in the product box for product warnings and other important information.
•
•
•
•
•
Cautions
Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.
When drilling or cutting, always check the opposite side of the surface. Be aware of fuel tanks, electrical cables, and hydraulic hoses.
Do not connect the CCU interface connector on either the CCU cable or the Autopilot Gateway to a NMEA 2000
®
network.
•
•
•
September 2009
190-01082-02 Rev. B
Printed in Taiwan