Garmin GMI 10 Digital Marine Instrument Display Installation Instructions, S/N
Garmin GMI 10 Digital Marine Instrument Display Manual
View all Garmin GMI 10 Digital Marine Instrument Display manuals
Add to My Manuals
Save this manual to your list of manuals |
Garmin GMI 10 Digital Marine Instrument Display manual content summary:
- Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 1
the best possible performance, install your GMI 10 Marine Instrument according to the following instructions. If you experience difficulty during the installation, contact Garmin Product Support, or seek the advice of a professional installer. The GMI 10 will communicate with NMEA 2000- or NMEA - Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 2
Installation Instructions Step 1: Select a Location for the GMI 10 Consider the following when you select an installation location: • Provides optimal viewing as you operate your vessel. • Allows easy access to the keypad on the GMI 10. • Is strong enough to support the weight of the GMI 10 and - Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 3
power wires, use 18 AWG wire. If your boat has an electrical system, you might be able to wire the GMI 10 directly to an unused holder on your current fuse block. If you of the GMI 10. For information on connecting to a NMEA 0183compatible device, see page 6. GMI 10 Installation Instructions - Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 4
more information on NMEA 2000, visit www.garmin.com. Follow the directions and reference the diagrams on page 5 to either connect the GMI 10 to your existing NMEA 2000 network, or an external switch. The GMI 10 will drain your battery if it is connected directly. GMI 10 Installation Instructions - Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 5
Network Notes: • To add additional sensors to your NMEA 2000 network, follow the instructions included with the sensor. • To learn more about NMEA 2000 and building a NMEA 2000 network, visit www.garmin.com. • The GMI 10 is not powered by the NMEA 2000 network, it must be separately connected to - Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 6
10, and connect the green wire (Rx/B) to ground. • The blue (Tx/A) and white (Tx/B) wires are used only when wiring the GMI 10 to a Garmin GPS 17/17x antenna. • The yellow (accessory on) wire is used only when wiring the GMI 10 to a Garmin GPS 17/17x antenna. GMI 10 Installation Instructions - Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 7
The GMI 10 is NMEA 2000 certified NMEA 0183 Sentence Information The GMI 10 can receive the following approved NMEA 0183 sentences from a NMEA 0183-compliant device: BOD, BWC, DBT, DPT, GGA, GLL, GSA, GSV, HDG, HDM, MDA, MTW, MWD, MWV, RMB, RMC, VHW, WPL, and XTE. GMI 10 Installation Instructions - Garmin GMI 10 Digital Marine Instrument Display | Installation Instructions, S/N - Page 8
/5/EC. To view the full Declaration of Conformity, see the Garmin Web site for your Garmin product: www.garmin.com/products/gmi10/. Click Manuals, and then select the Declaration of Conformity link. Software License Agreement BY USING THE GMI 10, YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF
GMI 10 Installation Instructions
To obtain the best possible performance, install your GMI 10 Marine Instrument according to the following instructions.
If you experience difficulty during the installation, contact Garmin Product Support, or seek the advice of a professional
installer.
The GMI 10 will communicate with NMEA 2000- or NMEA 0183-compatible sensors and devices, and can show
information such as speed, heading, water depth, and fuel information when connected to the appropriate sensors.
WARNING
: See the
Important Safety and Product Information
guide in the product box for product warnings and
other important information.
Product Registration
Help us better support you by completing our online registration at
www.garmin.com/registration/
.
For future reference, write down the serial number assigned to your GMI 10 in the space provided below. The serial
number is located on a sticker on the back of the GMI 10.
Serial number
Contact Garmin
Contact Garmin if you have any questions while installing or using your GMI 10. In the USA contact Garmin Product
Support by phone: (913) 397-8200 or (800) 800-1020; or go to
www.garmin.com/support/
.
In Europe, contact Garmin (Europe) Ltd. at +44 (0) 870.8501241 (outside the UK) or 0808 2380000 (within the UK).
Packing List and Accessories
Before installing your GMI 10, confirm that your package includes the following items. If any parts are missing, contact
your Garmin dealer immediately.
Standard Package
GMI 10 unit
Protective cover
Flush mount hardware
Power/data wiring harness
2 NMEA 2000 T-connectors
2 NMEA 2000 terminators (1 male, 1 female)
1 NMEA 2000 drop cable (2 m)
1 NMEA 2000 power cable (2m), (3 A fuse)
Installation instructions
•
•
•
•
•
•
•
•
•
Optional Accessories
Additional NMEA 2000 network components
Tools Needed
Jigsaw or 3
17
/
32
in. (90mm) hole saw,
Drill and drill bits
Center punch and hammer
Scissors
File and sandpaper
Phillips head screwdriver
Anti-seize lubricant (optional)
•
•
•
•
•
•
•
•
To install and use your GMI 10
1. Select a location.
2. Flush mount the GMI 10.
3. Connect the GMI 10 to power.
4. Connect the GMI 10 to sensors.
January, 2008
190-00892-02 Rev. B
Printed in Taiwan