Garmin GMR 604 xHD Open Array and Pedestal Installation Instructions
Garmin GMR 604 xHD Open Array and Pedestal Manual
View all Garmin GMR 604 xHD Open Array and Pedestal manuals
Add to My Manuals
Save this manual to your list of manuals |
Garmin GMR 604 xHD Open Array and Pedestal manual content summary:
- Garmin GMR 604 xHD Open Array and Pedestal | Installation Instructions - Page 1
Properly install your GMR 600/1200 series radar according to the following instructions. If you experience difficulty installing the chartplotter, seek the assistance of a professional installer, or contact Garmin® Product Support. Before installing your GMR 600/1200 series radar, confirm that the - Garmin GMR 604 xHD Open Array and Pedestal | Installation Instructions - Page 2
from smoke stacks or heat from lights. • The mounting surface or platform should be sturdy enough to support the weight of the radar and any inertial forces, as flat as possible, and parallel with the water distance should be increased to 7 ft. (2 m). GMR 600/1200 Series Installation Instructions - Garmin GMR 604 xHD Open Array and Pedestal | Installation Instructions - Page 3
or paste to the four studs prior to installation. 3. Install the seals onto the pedestal (Figure 3). Figure 1 Figure 2 Figure 3 Mounting the Radar Mount the radar with Offset = 180° Figure 4 GMR 600/1200 Series Installation Instructions Figure 5 Figure 6 flat washer spring washer M10 hex nut - Garmin GMR 604 xHD Open Array and Pedestal | Installation Instructions - Page 4
pedestal wave guide. 2. Verify that the antenna wave guide is aligned with the pedestal wave guide. Slide the antenna onto the pedestal. Align the 3. Secure the antenna to the pedestal butt connectors. Wire Gauge Table ◦ After the connector is the cable as needed, based on the type of Instructions - Garmin GMR 604 xHD Open Array and Pedestal | Installation Instructions - Page 5
Power converter + 10-40 Vdc (20-40 Vdc for the GMR 1204 - and 1206) To RF ground Power Wiring Diagram GMR 600/1200 Series Installation Instructions - Garmin GMR 604 xHD Open Array and Pedestal | Installation Instructions - Page 6
4000/5000 series chartplotter Expanded Garmin Marine Network Example NOTE: Each component of the expanded network must be installed according to its installation instructions. These diagrams only show how a GMR 404/406 radar interacts with a network and do not show proper wiring for other network - Garmin GMR 604 xHD Open Array and Pedestal | Installation Instructions - Page 7
a GPSMAP 4000 or 5000 series chartplotter, use a blank SD card to update the chartplotter or the network according to the instructions in the chartplotter owner's manual. If you have a GPSMAP 3000 series chartplotter, use a blank Garmin Data Card to update the chartplotter or the network according - Garmin GMR 604 xHD Open Array and Pedestal | Installation Instructions - Page 8
Untwist the wire pairs enough to ensure a proper connection. • Arrange individual wires in proper order according to the table shown above. For example, if you have identified the end of the cable in Step 4 as Side A, arrange the copper tape. GMR 600/1200 Series Installation Instructions - Garmin GMR 604 xHD Open Array and Pedestal | Installation Instructions - Page 9
careful not to overtighten the nut. 5. Install the O-ring onto the housing. The cable is now ready to use. O-Ring GMR 600/1200 Series Installation Instructions - Garmin GMR 604 xHD Open Array and Pedestal | Installation Instructions - Page 10
) Model GMR 604/1204 GMR 606/1206 L 51 /19 32 in. (1310 mm) 75 /45 64 in. (1923 mm) 10 GMR 600/1200 Series Installation Instructions - Garmin GMR 604 xHD Open Array and Pedestal | Installation Instructions - Page 11
Specifications Pedestal (Physical) manual gain adjust; manual or auto (AFC) receiver tuning; manual adjust for rain clutter and for sea clutter. Radar/Chart Overlay: Overlay mode is supported series chartplotters) Look ahead, Auto Shift and Manual (GPSMAP 3000 series chartplotters) Antenna RPM: - Garmin GMR 604 xHD Open Array and Pedestal | Installation Instructions - Page 12
radome has been installed according to the recommendations given in this guide, and that all personnel are clear of the radome before switching energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no - Garmin GMR 604 xHD Open Array and Pedestal | Installation Instructions - Page 13
readable form the Software or any part thereof or create any derivative works based on the Software. You agree not to export or re-export the . To obtain warranty service, contact your local Garmin authorized dealer or call Garmin Product Support for shipping instructions and an RMA tracking - Garmin GMR 604 xHD Open Array and Pedestal | Installation Instructions - Page 14
must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited. Information in this document is subject to change without notice. Garmin reserves the right to change or improve
GMR
™
600/1200 Series Radar Installation Instructions
Properly install your GMR 600/1200 series radar according to the following instructions.
If you experience difficulty installing the
chartplotter, seek the assistance of a professional installer, or contact Garmin
®
Product Support.
Before installing your GMR 600/1200 series radar, confirm that the package contains the items listed on the box. If any parts are missing,
contact your Garmin dealer immediately.
WARNING:
Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.
WARNING:
The selected radar mounting location must be able to hold the weight of the radar and withstand any inertial forces.
WARNING:
The radar transmits electromagnetic energy. It is important that the radar is turned off or the DC power input is disconnected when
personnel are required to come close to the radar to perform work on the radar assembly or associated equipment. Electromagnetic energy is harmful.
CAUTION:
When the radar is transmitting, do not look directly at the antenna at close range, because the eyes are the most sensitive part of the body to
electromagnetic energy.
NOTICE:
When drilling or cutting, always check the opposite side of the drilling or cutting surface.
Product Registration
Help us better support you by completing our online registration today. Go to
. Keep the original sales receipt, or a
photocopy, in a safe place.
Contact Garmin
Contact Garmin Product Support if you have any questions while installing your GMR 600/1200 series radar. In the USA, go to
www.garmin.com/suppor
t
, or contact Garmin USA by phone at (913) 397.8200 or (800) 800.1020.
In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.
In Europe, go to
www.garmin.com/suppor
t
and click
Contact Support
for in-country support information, or contact Garmin (Europe) Ltd. by
phone at +44 (0) 870.8501241.
Needed Tools
For Installing the Radar:
#2 Phillips screwdriver
5 mm Allen wrench
Drill and drill bits
Wrench and socket set
For Installing the Optional Field-Installable RJ-45 Network Connector:
Knife
Pliers
15 mm wrench
AMP modular-plug hand tool and die set or compatible equivalent
•
•
•
•
•
•
•
•
March 2010
190-01067-02 Rev. D
Printed in Taiwan