Garmin GMR Fantom 18x/24x Dome Radar Installation Instructions
Garmin GMR Fantom 18x/24x Dome Radar Manual
View all Garmin GMR Fantom 18x/24x Dome Radar manuals
Add to My Manuals
Save this manual to your list of manuals |
Garmin GMR Fantom 18x/24x Dome Radar manual content summary:
- Garmin GMR Fantom 18x/24x Dome Radar | Installation Instructions - Page 1
authorized service technician. Any damage resulting from opening the unit by anyone other than a Garmin authorized service technician software when you install this device. For instructions on updating the software, see your chartplotter owner's manual at support.garmin.com. Tools Needed • Drill - Garmin GMR Fantom 18x/24x Dome Radar | Installation Instructions - Page 2
targets. • The device should be mounted on a flat surface or a platform that is parallel to the vessel's water line and is sturdy enough to support the device's weight. The weight for each model is listed in the product specifications. • Most radar beams spread vertically 12.5° above and 12.5° below - Garmin GMR Fantom 18x/24x Dome Radar | Installation Instructions - Page 3
.) mounting holes. 2 Connect the power cable to the power port and the network cable to the network port . 3 Press the cables into any of the guide grooves on the bottom of the case, and secure them using a cable hold-down plate . The cables should be bent or twisted as little as - Garmin GMR Fantom 18x/24x Dome Radar | Installation Instructions - Page 4
Wiring and Connection Considerations It may be necessary to drill 32 mm (11/4 in.) holes for routing the power and network cables. • When routing multiple cables through the same hole, you must route the network cable before the power cable. • You must apply marine sealant to the hole after the - Garmin GMR Fantom 18x/24x Dome Radar | Installation Instructions - Page 5
functions of this radar are controlled with your Garmin chartplotter. See the Radar section of your chartplotter's owner's manual for operating instructions. To download the latest manual, go to support.garmin.com. If you have more than one radar on your boat, you must be viewing the radar screen - Garmin GMR Fantom 18x/24x Dome Radar | Installation Instructions - Page 6
Specifications Specification Weight GMR Fantom 18x Weight GMR Fantom 24x Temperature range Case material Maximum antenna rotation speed Input voltage Power consumption1 Fuse Power output Transmitter center frequency Transmitter maximum bandwidth Beam width GMR Fantom 18x Beam width GMR Fantom 24x - Garmin GMR Fantom 18x/24x Dome Radar | Installation Instructions - Page 7
Detailed Dimensions Item Length (width) (height) GMR Fantom 18x 508.2 mm (20 in.) 504.7 mm (19 7/8 in.) 248.3 mm (9 3/4 in.) GMR Fantom 24x 645.4 mm (25 7/16 in.) 642.5 mm (25 5/16 in.) 250.3 mm (9 7/8 in.) Item GMR Fantom 18x 233 mm (9 3/16 in.) GMR Fantom 24x 233 mm (9 3/16 in.) 227.5 mm (8 - Garmin GMR Fantom 18x/24x Dome Radar | Installation Instructions - Page 8
Extensions section of these instructions to make sure the can help troubleshoot installation problems. Status support for assis tance. Contacting Garmin Support • Go to support.garmin.com for help and information, such as product manuals, frequently asked questions, videos, and customer support - Garmin GMR Fantom 18x/24x Dome Radar | Installation Instructions - Page 9
物質宣言 铅 多溴联苯 SJ/T11364 GB/T26572 GB/T26572 产品 連絡地址 68 02)2642-8999 02)2642-9199 3.8.2 章節: © 2021 Garmin Ltd. or its subsidiaries Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. - Garmin GMR Fantom 18x/24x Dome Radar | Installation Instructions - Page 10
© 2021 Garmin Ltd. or its subsidiaries support.garmin.com
GMR
™
FANTOM
™
18X/24X
INSTALLATION
INSTRUCTIONS
Important Safety Information
WARNING
Failure to follow these warnings, cautions, and notices could result in personal injury, damage to the vessel or
device, or poor product performance.
See the
Important Safety and Product Information
guide in the product box for product warnings and other
important information.
The radar transmits electromagnetic energy. To avoid possible personal injury, damage to the vessel or device,
or poor product performance, ensure that the radar is installed according to the recommendations in these
instructions and that all personnel are clear of the path of the radar beam before transmitting. When properly
installed and operated, the use of this radar conforms to the requirements of ANSI/IEEE C95.1-1992 Standard
for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields.
To avoid possible personal injury, do not look directly at the antenna at close range when the radar is
transmitting. Eyes are the most sensitive part of the body to electromagnetic energy.
When connecting the power cable, do not remove the in-line fuse holder. To prevent the possibility of injury or
product damage caused by fire or overheating, the appropriate fuse must be in place as indicated in the
product specifications. In addition, connecting the power cable without the appropriate fuse in place voids the
product warranty.
CAUTION
This device should be used only as a navigational aid. Using the device for any purpose requiring precise
measurement or direction, distance, location, or topography may result in personal injury or damage to the
vessel.
To avoid possible personal injury, always wear safety goggles, ear protection, and a dust mask when drilling,
cutting, or sanding.
Opening the device may result in personal injury and/or damage to the device. This device contains no user-
serviceable parts, and should be opened only by a Garmin
®
authorized service technician. Any damage resulting
from opening the unit by anyone other than a Garmin authorized service technician will not be covered by the
Garmin warranty.
NOTICE
When drilling or cutting, always check what is on the opposite side of the surface to avoid damaging the vessel.
Software
Update
You must update the Garmin chartplotter software when you install this device. For instructions on updating
the software, see your chartplotter owner's manual at
support.garmin.com
.
Tools Needed
•
Drill
•
9.5 mm (
3
/
8
in.) drill bit
•
32 mm (1
1
/
4
in.) drill bit (optional)
•
4 mm (
5
/
32
in.) hex wrench
•
13 mm (
1
/
2
in.) wrench and torque wrench
•
Marine sealant
GUID-37571E09-A387-48EF-9FD8-D98FD43CBF80 v1
October 2021