Garmin GPSMAP 396 Yoke Mount Instructions  

GPSMAP 196/296/396 Y

OKE

M

OUNT

I

NSTALLATION

I

NSTRUCTIONS

The GPSMAP 196/296/396 Yoke Mount comes fully assembled and includes:

WARNING

:

It is the sole responsibility of the owner/operator of the

GPSMAP 196/296/396 to place this mount and secure the unit so that it will not

interfere with the aircraft’s operating controls and safety devices, or cause damage

or personal injury in the event of an accident or turbulence. Do not mount the

GPSMAP 196/296/396 in a place where the pilot or passengers are likely to impact it

in an accident, collision, or turbulence. The mounting hardware provided by Garmin is

not warranted against turbulence, collision damage, or related consequences.

The yoke mount is packaged pre-assembled and includes a short clamp adjustment knob,

a cable clamp, and Allen wrench.

Larger yoke control shafts or center column arms require the short clamp adjustment

knob for correct configuration. Refer to page 4 for instructions on changing adjustment

knobs.

The yoke mount is designed to fit the majority of conventional aircraft yokes and center

column controls. When you remove this yoke mount from the package, it is configured

for conventional aircraft yokes. If you have center column control, you must remove

the clamp assembly from the rest of the yoke mount. Rotate the clamp 90

o

so that the

open end of the clamp faces away from you and reattach it to the rest of the yoke mount.

Refer to the illustrations and instructions on page 3.

Allen Wrench

Short Clamp

Adjustment Knob

Long Clamp Adjustment Knob

Cable Clamp

GPSMAP 196/296/396 Cradle

1

4

The long clamp adjustment knob shaft can protrude too far down when fully tightened

onto larger type control shafts and center column arms, creating an obstruction or

hazard. Use the short clamp adjustment knob to remove the obstruction.

To replace clamp adjustment knobs:

1.

Remove the rubber padding

from the lower clamp by carefully

peeling it away to reveal the Allen

screw. This screw secures the

lower clamp to the long clamp

adjustment knob.

2.

Use the supplied Allen wrench to

remove the screw, washer, and

lower clamp from the long clamp

adjustment knob.

3.

Remove the long clamp

adjustment knob by turning it

counter-clockwise.

4.

Install the short clamp adjustment

knob by turning it clockwise until

it protrudes through the clamp

frame.

5.

Reassemble the washer and

Allen screw onto the short clamp

adjustment knob and tighten.

6.

Reinstall the rubber padding.

NOTE:

Verify the lower clamp is properly oriented in the clamp frame as illustrated.

A cable clamp is provided on the top of the yoke mount to secure the 12-Volt adapter

cable provided with the GPSMAP 196/296/396. If you intend to use your GPSMAP

196/296/396 primarily in an aircraft and not in an automobile, you can secure the cable

with this clamp. Use of the clamp reduces the risk of loose wires becoming a hazard

during operation of the aircraft controls.

© Copyright 2005 Garmin Ltd. or its subsidiaries

Garmin International, Inc.

1200 East 151st Street, Olathe, Kansas

66062, U.S.A.

Garmin (Europe) Ltd.

Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K.

Garmin (Asia) Corporation

No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan

www.garmin.com

Printed in Taiwan

Part Number 190-00603-00 Rev. B

Rubber

Padding

Allen Head

Screw

Lower Clamp

Short Clamp

Adjustment

Knob

Washer

Garmin GPSMAP 396 Yoke Mount Instructions

Garmin GPSMAP 396 - Aviation GPS Receiver Manual

Garmin GPSMAP 396 manual content summary:

Garmin GPSMAP 396 Yoke Mount Instructions &nbsp;

Garmin GPSMAP 396 - Aviation GPS Receiver Manual

Garmin GPSMAP 396 manual content summary:

Garmin GPSMAP 396 Yoke Mount Instructions