Garmin GPSMAP 546S Flush Mount Kit Instructions (multilingual)
Garmin GPSMAP 546S - Marine GPS Receiver Manual
UPC - 753759096168
View all Garmin GPSMAP 546S manuals
Add to My Manuals
Save this manual to your list of manuals |
Garmin GPSMAP 546S manual content summary:
- Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 1
EN Installing the Flush Mount Kit Use this kit to flush mount a GPSMAP 500 series unit into a flat panel. • Select an appropriately sized location for the unit. • Use the Flush Mount Template provided to determine a location. • Check that - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 2
2 NOTE: You must connect the wiring harness to the boat's power supply, GPS antenna, XM antenna (if applicable), and transducer (if applicable) per the installation instructions included with the unit. - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 3
panneau Utilisez ce kit pour monter un appareil de la série GPSMAP 500 sur un panneau plat. • Sélectionnez un emplacement de n'y a que très peu d'espace entre le boîtier de l'appareil et les bras du support. Découpez légèrement à l'intérieur de la ligne indiquée, puis poncez ou limez le panneau - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 4
le trou que vous venez de découper dans la surface de montage. • Glissez les supports de tension de la base sur les vis à tête hexagonale et fixez-les à l' parfaitement. Appareil assemblé et matériel de montage sur panneau Supports de fixation Ecrous à oreilles Figure 2 REMARQUE : vous devez - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 5
IT Installazione del kit opzionale per il montaggio a incasso Questo kit consente di eseguire l'installazione a incasso dell'unità GPSMAP serie 500 su un pannello piatto. • Selezionare una posizione di installazione di dimensioni appropriate per l'unità. • Per determinare se la posizione è adatta, - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 6
IT 3. Installare l'unità nell'apertura (vedere la figura 2): • Posizionare l'alloggiamento dell'unità nel foro praticato sulla superficie di montaggio. • Inserire le staffe per il montaggio in tensione sui bulloni esagonali e fissare con i quattro dadi ad alette. • Serrare i quattro dadi ad alette - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 7
DE Installieren des Einbau-Montagesatzes Verwenden Sie diesen Montagesatz, um ein Gerät der GPSMAP 500-Serie bündig in eine Tafel einzubauen. • Wählen Sie einen für die Größe des Geräts passenden Einbauort aus. • Verwenden Sie die Montageschablone, um diesen Einbauort - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 8
3. Montieren Sie das Gerät in der Öffnung (siehe Abbildung 2): • Schieben Sie das Gerätegehäuse in die zuvor in die Montageoberfläche gesägte Öffnung. • Schieben Sie die Halterungen auf die Sechskantschrauben, und befestigen Sie sie mit den vier Flügelmuttern. • Ziehen Sie die vier Flügelmuttern an, - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 9
ES Instalación del kit de montaje alineado Utilice este kit para el montaje alineado de una unidad de la serie GPSMAP 500 en un panel plano. • Seleccione una ubicación del tamaño adecuado para la unidad. • Utilice la plantilla de montaje alineado proporcionada para determinar la ubicación. • - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 10
3. Instale la unidad en la abertura (consulte la ilustración 2): • Coloque la carcasa en el orificio que acaba de realizar en la superficie de instalación. • Coloque los soportes de montaje por tensión sobre los tornillos hexagonales y asegúrelos con las cuatro palomillas. • Apriete las cuatro - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 11
Instalar o Kit de Montagem Embutida Utilize este kit para a montagem embutida da unidade da Série GPSMAP 500 num painel plano. • Seleccione um local de montagem com as dimensões adequadas. • Utilize o modelo de montagem embutida fornecido para escolher o local. • Certifique-se - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 12
3. Instalar a unidade na abertura (ver a figura 2): • Coloque a armação na abertura na superfície de montagem. • Introduza os suportes de montagem nos parafusos sextavados e fixe-os com as porcas de orelhas. • Aperte as porcas. Não aperte demasiado. • Se não o fez no passo 2, ligue os cabos à - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 13
De inbouwkit installeren Met deze kit kunt u een apparaat uit de GPSMAP 500-serie in een vlak paneel monteren. • Kies een locatie met voldoende ruimte om het apparaat te monteren. • Bepaal met behulp van het bijgeleverde installatiesjabloon - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 14
3. Monteer het apparaat in de opening (zie afbeelding 2): • Plaats de apparaatbehuizing in de opening die u zojuist in het montageoppervlak hebt uitgezaagd. • Schuif de montagesteunen op de zeskantbouten en zet deze vast met de vier vleugelmoeren. • Draai de vier vleugelmoeren aan om de - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 15
Sådan installerer du sættet til planmontering Brug dette sæt til at planmontere en enhed fra GPSMAP 500-serien i et fladt panel. • Vælg en placering med den rette størrelse til enheden. • Brug planmonteringsskabelonen for at fastsætte en placering. • Kontroller, at - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 16
3. Installer enheden i åbningen (se Figur 2): • Placer huset i det hul, du netop har skåret ud i monteringsoverfladen. • Skub tilstramningsbeslagene henover de sekskantede bolte, og fastgør dem med de fire fanemøtrikker. • Stram de fire fanemøtrikker for at fiksere huset på monteringsoverfladen. Pas - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 17
Tasokiinnityssarjan asentaminen Tämän sarjan avulla voit asentaa GPSMAP 500 -sarjan laitteen tasaiseen paneeliin. • Valitse laitteelle sopivankokoinen asennuspaikka. • Määritä paikka sarjan mukana toimitetun tasokiinnitysmallin avulla. • Tarkista, että kaikki kaapelit ulottuvat laitteen - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 18
3. Asenna laite aukkoon (kuva 2): • Aseta laitteen kotelo kiinnityspintaan sahattuun aukkoon. • Aseta kiristimet kuusiopultteihin ja kiristä ne siipiruuveilla. • Kiinnitä laitteen kotelo kiinnityspintaan kiristämällä siipiruuvit. Älä kiristä niitä liian tiukalle. • Liitä johdinsarja laitteeseen (jos - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 19
Installere settet for innebygging Bruk dette settet hvis du vil bygge en enhet i GPSMAP 500-serien inn i et flatt panel. • Velg en plassering der det er god nok plass til enheten. • Bruk malen for innebygging, som følger med, for å - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 20
3. Installere enheten i åpningen (se Figur 2): • Sett huset inn i hullet du nettopp har skåret ut i monteringsoverflaten. • Skyv monteringsbrakettene inn på sekskantboltene og fest dem med de fire vingemutterne. • Trekk til de fire vingemutterne for å feste huset til monteringsoverflaten. Pass på at - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 21
Installera satsen för nedsänkt montering Använd den här satsen för nedsänkt montering av en GPSMAP 500-enhet i en platt panel. • Välj en plats med lämplig storlek för enheten. • Bestäm plats med hjälp av den medföljande mallen för nedsänkt montering. • - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 22
3. Montera enheten i öppningen (se figur 2): • Placera enhetens hölje i det nyskurna hålet i monteringsytan. • Skjut på monteringsfästena på sexkantsbultarna och fäst dem med de fyra vingmuttrarna. • Fäst enheten i monteringsytan genom att dra åt de fyra vingmuttrarna. Se upp så du inte drar åt för - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 23
GPSMAP серии 500 1 1 2 4 4 4 шт.). 3/8" (10 9/32" (7 мм). 1 3/8" (10 2 1). 9/32" (7 3). GPS XM 3). RU 2007 1 190-00553-01 B - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 24
3 2). 2 Рис. 2 GPS XM RU - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 25
Instalacija kompleta za ugradbenu montažu Ovaj komplet koristite za ugradbenu montažu uređaja GPSMAP serije 500 u ravnu ploču. • Odaberite mjesto koje odgovara veličini uređaja. • Za određivanje mjesta ugradbene montaže upotrijebite šablonu. • Provjerite dosežu li svi kabeli - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 26
3. Smjestite jedinicu u otvor (vidi sliku 2): • Postavite kućište jedinice u izrezani otvor na površini za montažu. • Gurnite montažne nosače na šesterokutne vijke i učvrstite ih pomoću četiri matice. • Pritegnite četiri leptir-matice kako biste učvrstili kućište na površinu za montažu. Pazite da ih - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 27
GPSMAP 500 1 1 2 4 4 4 3/8" (10 mm 9/32" (7 mm). 1 3/8" (10 mm 2 1): 9/32" (7 mm 3) GPS XM 3 Μονάδα EL 2007 1 190-00553-01 Rev. B - Garmin GPSMAP 546S | Flush Mount Kit Instructions (multilingual) - Page 28
3 2): 2 2 GPS XM EL
October 2007
Part Number 190-00553-01 Rev. B
Printed in Taiwan
Installing the Flush Mount Kit
Use this kit to flush mount a GPSMAP 500 series unit into a flat panel.
Select an appropriately sized location for the unit.
Use the Flush Mount Template provided to determine a location.
Check that all cables reach the unit mounting location.
Always wear safety goggles and a dust mask when drilling, cutting, or sanding.
Included mounting hardware
—(1) unit housing, (1) rubber seal, (2) tension mount brackets, (4) hex bolts, (4) hex nuts, and (4) wing nuts.
Tools (not included)
—drill,
3
/
8
"
(10 mm) drill bit, jig saw, and a
9
/
32
"
(7 mm) wrench.
To install the Flush Mount Kit:
1. Cut the opening:
The flush mount template has adhesive on the back. Remove the protective liner and apply the template to the location you want to
mount the unit.
Using a
3
/
8
" (10 mm) drill bit, drill the pilot holes indicated on the template to begin cutting the mounting surface.
Using the jig saw, cut the mounting surface along the inside of the line indicated on the template. Be very careful when cutting this
hole, because there is only a small amount of clearance between the unit housing and the tension mount arms. Cut slightly inside the
indicated line and then sand or file the panel as needed to obtain the best fit.
2. Assemble the flush mount hardware (see Figure 1):
Attach the rubber seal to the front of the unit housing.
Insert the four hex bolts into the unit housing so they stick out of the back.
Use the four hex nuts to secure the hex bolts to the unit housing. Using the
9
/
32
" (7 mm) wrench, tighten the nuts without
overtightening.
Slide the unit into the unit housing. (If you have limited space behind the mounting surface, this can be done in step 3.)
When the unit is inserted correctly, it will snap into place within the unit housing.
Connect the wiring harness, GPS antenna, and XM antenna (if applicable) to the unit. (This can also be done in step 3, if necessary.)
Unit
Rubber seal
Hex bolts
Hex nuts
Hex nuts
Hex bolts
Figure 1
Unit housing
•
•
•
•
•
•
•
•
•
•
•
•
•
EN