Garmin Intelliducer NMEA 2000 Thru-hull Sensor 0-12° deadrise Installatio
Garmin Intelliducer NMEA 2000 Thru-hull Sensor 0-12° deadrise Manual
View all Garmin Intelliducer NMEA 2000 Thru-hull Sensor 0-12° deadrise manuals
Add to My Manuals
Save this manual to your list of manuals |
Garmin Intelliducer NMEA 2000 Thru-hull Sensor 0-12° deadrise manual content summary:
- Garmin Intelliducer NMEA 2000 Thru-hull Sensor 0-12° deadrise | Installatio - Page 1
the following instructions. If you experience difficulty during the installation, contact Garmin Product Support, or seek the advice of a professional installer. This Transom Mount Intelliducer provides depth information either to a NMEA 0183compatible device, or to your existing NMEA 2000® network - Garmin Intelliducer NMEA 2000 Thru-hull Sensor 0-12° deadrise | Installatio - Page 2
Install the Intelliducer To install the Transom Mount Intelliducer: 1. Assemble the Intelliducer. 2. Mount the Intelliducer. 3. Connect the Intelliducer your existing NMEA 2000 network. OR Connect the Intelliducer to power and a NMEA 0183-compatible device. 4. Update your Garmin chartplotter (if - Garmin Intelliducer NMEA 2000 Thru-hull Sensor 0-12° deadrise | Installatio - Page 3
NMEA 2000 cable to the backbone of your existing NMEA 2000 network. OR Route the power/data cable to power and a NMEA 0183-compliant device. Caution: Avoid routing the cable close to electrical wires or other sources of electrical interference. Transom Mount Intelliducer Installation Instructions - Garmin Intelliducer NMEA 2000 Thru-hull Sensor 0-12° deadrise | Installatio - Page 4
added to your NMEA 2000 network. Existing NMEA 2000 network (not included) T-connector (included) Drop cable (built-in) Additional NMEA 2000 device (not included) Transom mount Intelliducer Connecting the Intelliducer to a NMEA 2000 Network Transom Mount Intelliducer Installation Instructions - Garmin Intelliducer NMEA 2000 Thru-hull Sensor 0-12° deadrise | Installatio - Page 5
Spare > > Transom Mount NMEA 0183 Intelliducer Power/Data Cable NMEA 0183 Intelliducer +Battery- Fuse 12 Vdc 2 A Red Black Orange > Gray > White/Red Power Ground ACC On Rx A(+) > Rx B(-) > NMEA 0183Compliant Device Transom Mount NMEA 0183 Intelliducer Wired to a NMEA 0183-compliant Device - Garmin Intelliducer NMEA 2000 Thru-hull Sensor 0-12° deadrise | Installatio - Page 6
Information Water Depth Temperature Garmin Intelliducers are NMEA 2000 certified NMEA 0183 Information The Transom Mount NMEA 0183 Intelliducer communicates with NMEA 0183 devices using the SDDPT, SDDBT, and SDMTW NMEA 0183 sentences. Transom Mount Intelliducer Installation Instructions - Garmin Intelliducer NMEA 2000 Thru-hull Sensor 0-12° deadrise | Installatio - Page 7
relevant provisions of Directive 1999/5/EC. To view the full Declaration of Conformity, see the Garmin Web site for your Garmin product: www.garmin.com/products/intelliducer/. Click Manuals, and then select the Declaration of Conformity link. Transom Mount Intelliducer Installation Instructions - Garmin Intelliducer NMEA 2000 Thru-hull Sensor 0-12° deadrise | Installatio - Page 8
express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual onto a hard drive or other Garmin products. Garmin® is a trademark of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. Intelliducer™ is a trademark of Garmin
Transom Mount Intelliducer
™
Installation Instructions
To obtain the best possible performance, install your Transom Mount Intelliducer according to
the following instructions. If you experience difficulty during the installation, contact Garmin
Product Support, or seek the advice of a professional installer.
This Transom Mount Intelliducer provides depth information either to a NMEA 0183-
compatible device, or to your existing NMEA 2000
®
network, depending on the model. For
more information about NMEA 2000, visit
www.garmin.com
.
WARNING
: See the
Important Safety and Product Information
guide in the product box for
product warnings and other important information.
Product Registration
Help us better support you by completing our online registration today! Connect to our Web site
at
. Keep the original sales receipt, or a photocopy, in a safe place.
For future reference, write the serial number assigned to your Intelliducer in the space provided.
The serial number is located on a sticker around the cable.
Serial number
Contact Garmin
Contact Garmin if you have any questions while installing or using your Intelliducer. In the
USA contact Garmin Product Support by phone: (913) 397-8200 or (800) 800-1020, or go to
www.garmin.com/support/
.
In Europe, contact Garmin (Europe) Ltd. at +44 (0) 870.8501241 (outside the UK) or 0808
2380000 (within the UK).
Packing List and Tools Needed
Before installing your Intelliducer, confirm that your package includes the following items. If
any parts are missing, contact your Garmin dealer immediately.
Standard Package
•
Transom Mount Intelliducer (not pictured)
A
– 5 mm flat washers (2)
B
–5
×
30 mm screws (2)
C
– 10-32 lock nut (1)
D –4
×
12 mm screw (4)
E
– 10-32
×
1.75 in. screw (1)
F
–
1
/
4
in. cable clamps (2)
G – Plastic spacer (1)
H–
1
/
4
in. rubber washer (1)
I
– Cable tie, 5.6 in. (4)
J
– Cable entry cover (1)
K
– NMEA 2000 T-connector (1)
(NMEA 2000 Intelliducer only)
F
H
C
D
K
I
J
G
E
A
B
Tools Needed
•
Drill and drill bits
•
3
/
8
in. (9.5 mm) wrench or socket
•
Masking tape
•
Number 2 Phillips screwdriver
•
Marine sealant
March 2008
190-00889-01 Rev. B
Printed in Taiwan