Home » Garmin Manuals » Exercise and Fitness » Garmin Vector 3/3S » Manual Viewer

Garmin Vector 3/3S Owners Manual

Garmin Vector 3/3S Manual

View all Garmin Vector 3/3S manuals

Add to My Manuals
Save this manual to your list of manuals

Garmin Vector 3/3S manual content summary:

Garmin Vector 3/3S | Owners Manual - Page 1
VECTOR™ 3 AND VECTOR 3S Owner's Manual
Garmin Vector 3/3S | Owners Manual - Page 2
rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization
Garmin Vector 3/3S | Owners Manual - Page 3
Compatible Devices 6 Edge 1000 Instructions 6 Edge 520 and Edge 820 Instructions 6 Forerunner® 935 and fēnix® 5 Series Instructions 6 Appendix 6 Registering Your Vector System 6 Upgrading Your Vector 3S to a Dual Sensing System 6 Power Data Fields 7 Troubleshooting 8 Index 9 Table of
Garmin Vector 3/3S | Owners Manual - Page 4
Garmin Vector 3/3S | Owners Manual - Page 5
the Vector 3 system. The Vector 3S system installation is the same, but the power sensor components are in the left pedal only. For more information, see About the Vector 3S System, page 2. 1 Install the right pedal first. 2 Apply a thin layer of grease on the pedal spindle threads. NOTE: Garmin
Garmin Vector 3/3S | Owners Manual - Page 6
. About the Vector 3S System The single-sensing Vector 3S measures forces on the left pedal in order to approximate your total power. For information about upgrading, see Upgrading Your Vector 3S to a Dual Sensing System, page 6. NOTE: The Vector 3S system does not support cycling dynamics. Pairing
Garmin Vector 3/3S | Owners Manual - Page 7
where you produce positive power. Platform Center Offset Platform center offset is the location on the pedal platform where you apply force. Vector Data Your ride data or history is recorded to your Edge device or another compatible Garmin device. This section contains instructions for the Edge 1030
Garmin Vector 3/3S | Owners Manual - Page 8
hex key to remove the battery cover . Vector Specifications Battery type User-replaceable, 3 options: CR1/3N, 3 V, 1 per pedal LR44 or SR44, 1.5 V, 2 per pedal NOTE: Garmin recommends replacing all of the batteries at the same time. Do not mix the battery types. Battery life Up to 120 hr. of
Garmin Vector 3/3S | Owners Manual - Page 9
(PH 00) to remove the two screws from inside the battery carriage . 5 Remove the battery carriage. 6 While securely holding the wrench flats with a pedal wrench, use the 12 mm socket wrench to unscrew the spindle nut . NOTE: The right pedal has a black spindle nut and a reverse thread. The left
Garmin Vector 3/3S | Owners Manual - Page 10
sales receipt, or a photocopy, in a safe place. Upgrading Your Vector 3S to a Dual Sensing System Before you install the new right pedal, the left pedal must be paired and connected to a compatible Edge device or the Garmin Connect app. 1 Review the Vector installation instructions (Installing
Garmin Vector 3/3S | Owners Manual - Page 11
If you have another compatible device, see your device owner's manual. NOTE: Data fields that display pedal smoothness, torque effectiveness, and balance data are not supported by the Vector S system. Balance: The current left/right power balance. Balance - 10s Avg.: The 10-second moving average of
Garmin Vector 3/3S | Owners Manual - Page 12
arm a few times. The Edge device prompts you to install any pending software updates. 4 Follow the on-screen instructions. Resetting the Vector Pedals If the device stops responding, you may need to reset it by disconnecting and reconnecting the battery cover. This does not erase any of your data
Garmin Vector 3/3S | Owners Manual - Page 13
3 pedals 1, 2, 4 platform center offset 3 power 2 power (force), meters 2 power phase 3 product registration 6 R registering the device 6 resetting the device 8 S settings 3 smartphone, pairing 3 specifications 4 storing data 3 storing the device 6 T tools 1 training 4 troubleshooting 8 U upgrading
Garmin Vector 3/3S | Owners Manual - Page 14
support.garmin.com June 2020 GUID-297604DF-2345-43A4-80D2-908E16676B29 v5

Section	Page
Table of Contents	3
Introduction	5
Thank You	5
Getting Started	5
Tools Needed	5
Installing the Vector Components	5
Preparing for the Installation	5
Installing the Pedals	5
Pedal Status LED	5
Installing the Shoe Cleats	5
Adjusting the Release Tension	6
About the Vector 3S System	6
Pairing Vector with Your Edge 1030	6
Your First Ride	6
Entering the Crank Length	6
Customizing the Data Fields	6
Training	6
Pedal-Based Power	6
Cycling Dynamics	6
Using Cycling Dynamics	6
Power Phase Data	7
Platform Center Offset	7
Vector Data	7
Pairing Vector with the Garmin Connect App	7
Sending Your Ride to Garmin Connect	7
Garmin Connect	7
Disconnecting the USB Cable	7
Customizing the Settings in the Garmin Connect App	7
Device Information	7
Vector Device Care	7
Maintenance Tips	8
Vector Specifications	8
Battery Information	8
Replacing the Batteries	8
Overhauling the Vector Pedals	8
Vector Storage	10
Other Compatible Devices	10
Edge 1000 Instructions	10
Pairing Vector with the Edge 1000	10
Entering the Crank Length with the Edge 1000	10
Edge 520 and Edge 820 Instructions	10
Pairing Vector with the Edge 520 and Edge 820	10
Entering the Crank Length with the Edge 520 and Edge 820	10
Forerunner®‎ 935 and fēnix®‎ 5 Series Instructions	10
Pairing Vector with Your Forerunner 935 and fēnix 5 Series	10
Entering the Crank Length with the Forerunner 935 and fēnix 5 Series	10
Appendix	10
Registering Your Vector System	10
Upgrading Your Vector 3S to a Dual Sensing System	10
Power Data Fields	11
Troubleshooting	12
Updating the Vector Software Using the Edge 520, 820, 1000, or 1030	12
Resetting the Vector Pedals	12
Performing a Static Torque Test	12

Match case Limit results 1 per page

VECTOR

™

3 AND

VECTOR

Owner’s Manual