Garmin echo 101 Installation Instructions

Garmin echo 101 Manual

Get Garmin echo 101 PDF manuals and user guides View all Garmin echo 101 manuals
Add to My Manuals
Save this manual to your list of manuals

Garmin echo 101 manual content summary:

  • Garmin echo 101 | Installation Instructions - Page 1
    .com. • Keep the original sales receipt, or a photocopy, in a safe place. Contacting Garmin Product Support • Go to www.garmin.com/ support and click Contact Support for in-country support information. • In the USA, call (913) 397. 8200 or (800) 800. 1020. • In the UK, call 0808 2380000. • In
  • Garmin echo 101 | Installation Instructions - Page 2
    between the device and transducer. Go to www.garmin.com or contact your local Garmin® dealer to determine the appropriate type of transducer for your needs. 1 Follow the instructions provided with your transducer to correctly install it on your boat. 2 Route the transducer cable to the back
  • Garmin echo 101 | Installation Instructions - Page 3
    type of transducer, select it from the list. 2 Tilt the device forward, and lift it out of the cradle. Specifications Specification Case Models All models Temperature Range echo 101 and 201 series echo 301 and 501 series Measurement Fully gasketed, high-impact plastic, water resistant to
  • Garmin echo 101 | Installation Instructions - Page 4
    logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. echo™ is a trademark of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. © 2013 Garmin Ltd. or its subsidiaries www.garmin.com/support
  • 1
  • 2
  • 3
  • 4
echo™ Installation Instructions
Important Safety Information
WARNING
See the
Important Safety and Product Information
guide in the
product box for product warnings and other important
information.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
Registering Your Device
Help us better support you by completing our online registration
today.
•
Go to
.
•
Keep the original sales receipt, or a photocopy, in a safe
place.
Contacting Garmin Product Support
•
Go to
www.garmin.com/support
and click
Contact Support
for in-country support information.
•
In the USA, call (913) 397.8200 or (800) 800.1020.
•
In the UK, call 0808 2380000.
•
In Europe, call +44 (0) 870.8501241.
Tools Needed
•
Drill and drill bits
•
#2 Phillips screwdriver
•
Marine sealant
•
3
/
8
in. wrench or socket
•
Masking tape
•
Hardware for the swivel mount (not included)
◦
Self-tapping, pan-head wood screws or pan-head bolts,
either size #8 or a diameter of
5
/
32
in. (4 mm)
◦
Appropriate washers and nuts (if selecting bolts)
◦
Appropriate drill bit for drilling the pilot hole
Mounting Considerations
The fishfinder device can be mounted using the included swivel-
mount bracket, or it can be mounted flush with the dashboard
using the appropriate flush-mount kit (sold separately).
Before permanently installing any part of your device, you
should plan the installation by determining the location of the
various components.
•
The mounting location must provide a clear view of the
screen and access to the keys on the device.
•
The mounting location must be sturdy enough to support the
device and the mount.
•
The cables must be long enough to connect the components
to each other and to power.
•
The cables can be routed under the swivel mount or behind
the device.
•
To avoid interference with a magnetic compass, the device
should not be installed closer to a compass than the
compass-safe distance value listed in the product
specifications.
Installing the Swivel Base
Preparing to Run Cables under the Mounting Surface
NOTICE
Use pan-head screws or bolts when securing the swivel-mount
base. Screws or bolts with countersunk heads damage the
base.
Before you can prepare the swivel-mount base, you must
choose the location to install the mount and decide whether to
attach the mount using screws or bolts.
1
Remove the 10 mm M6x1 Phillips screw
À
and separate the
swivel mount
Á
from the base
Â
.
2
Orient the swivel base so the pass-through holes
Ã
face the
desired direction.
3
Using the swivel base as a template, mark the pilot hole
locations
Ä
.
4
Mark the cable routing hole
Å
.
5
Using the appropriate drill bit for the hardware, drill the three
pilot holes.
6
Using a
5
/
8
in. (16 mm) drill, drill a hole through the mounting
surface at the location you marked in step 4.
Fastening the Swivel Mount without the Cables
Running through the Mount
You should complete this procedure only if you are not running
the power and transducer cables under the mounting surface
and through the swivel-mount base.
November 2013
190-01708-02_0A
Printed in Taiwan