GE 26928GE1 User Guide

T

ELEPHONE

J

ACK

R

EQUIREMENTS

To use this phone, you need an RJ11C type modular telephone jack, which might look like

the one pictured here, installed in your home. If you don’t have a modular jack, call your

local phone company to find out how to get one installed.

D

IGITAL

S

ECURITY

S

YSTEM

Your cordless phone uses a digital security system to provide protection against false ringing, unauthorized

access, and charges to your phone line.

When you place the handset in the base, the unit verifies its security code. After a power outage or battery

replacement, you should place the handset in the base for about 20 seconds to reset the code.

I

NSTALLATION

AND

S

ET

U

P

INSTALLATION NOTE:

Some cordless telephones operate at frequencies that may cause interference to nearby TVs,

microwave ovens, and VCRs. To minimize or prevent such interference, the base of the cordless telephone should not be placed

near or on top of a TV, microwave oven, or VCR. If interference continues, moving the cordless telephone farther away from the

TV or VCR will often reduce or eliminate the interference.

Certain other communications devices may also use the 900 MHz frequency for communication, and, if not

properly set, these devices may interfere with each other and/or your new telephone. If you are concerned with

interference, please refer to the owner’s manual for these devices on how to properly set channels to avoid

interference. Typical devices that may use the 900 MHz frequency for communication include wireless audio/video

senders, wireless computer networks, multi-handset cordless telephone systems, and some long-range cordless

telephone systems.

I

MPORTANT

I

NSTALLATION

I

NFORMATION

•

Never install telephone wiring during a lightning storm.

•

Never touch uninsulated telephone wires or terminals, unless the telephone line has been disconnected at the

network interface.

•

Use caution when installing or modifying telephone lines.

•

Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

D

ESKTOP

I

NSTALLATION

40-Channel 900 MHz

Cordless Telephone

User’s Guide

E

QUIPMENT

A

PPROVAL

I

NFORMATION

Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15

and 68, FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA.

1

Notification to the Local Telephone Company

On the bottom of this equipment is a label indicating, among other information, the US number and Ringer Equivalence Number

(REN) for the equipment. You must, upon request, provide this information to your telephone company.

The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these

devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices connected to

one line should not exceed 5. To be certain of the number of devices you may connect to your line as determined by the REN, you

should contact your local telephone company.

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC

Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is

designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.

Notes

•

This equipment may not be used on coin service provided by the telephone company.

•

Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone equipment if you are on

a party line. Check with your local telephone company.

•

Notice must be given to the telephone company upon permanent disconnection of your telephone from your line.

•

If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this product

does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your

telephone company or a qualified installer.

2

Rights of the Telephone Company

Should your equipment cause trouble on your line which may harm the telephone network, the telephone company shall, where

practicable, notify you that temporary discontinuance of service may be required. Where prior notice is not practicable and the

circumstances warrant such action, the telephone company may temporarily discontinue service immediately. In case of such

temporary discontinuance, the telephone company must: (1) promptly notify you of such temporary discontinuance; (2) afford you the

opportunity to correct the situation; and (3) inform you of your right to bring a complaint to the Commission pursuant to procedures set

forth in Subpart E of Part 68, FCC Rules and Regulations.

The telephone company may make changes in its communications facilities, equipment, operations or procedures where such action is

required in the operation of its business and not inconsistent with FCC Rules and Regulations. If these changes are expected to affect

the use or performance of your telephone equipment, the telephone company must give you adequate notice, in writing, to allow you to

maintain uninterrupted service.

I

NTERFERENCE

I

NFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the interference).

•

Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna.

•

Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is connected.

If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television technician for

additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet, “How To Identify and Resolve

Radio/TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402. Please

specify stock number 004-000-00345-4 when ordering copies.

H

EARING

A

ID

C

OMPATIBILITY

This telephone system meets FCC standards for Hearing Aid Compatibility.

US NUMBER IS LOCATED ON THE CABINET BOTTOM

REN NUMBER IS LOCATED ON THE CABINET BOTTOM

We bring good things to life.

I

NTRODUCTION

CAUTION:

When using telephone equipment, there are basic safety instructions that should always be

followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them

for future reference.

Your Cordless Telephone is designed to give you flexibility in use and high quality performance. To get the most

from your new cordless telephone, we suggest that you take a few minutes right now to read through this

instruction manual.

IMPORTANT:

Because cordless phones operate on electricity, you should have at least one phone in your home that is

not cordless, in case the power in your home goes out.

B

EFORE

Y

OU

B

EGIN

P

ARTS

C

HECKLIST

Make sure your package includes the items shown here.

Handset

Base

AC power supply

Telephone line cord

TALK

2

5

8

0

3

6

9

1

4

7

*

1.

Set the ringer switch (on the handset front) to ON, and place handset in the cradle on the base.

2.

Plug the power supply into the power jack on the bottom of the base and the other end into an electrical outlet.

The “in use/charge” indicator comes on verifying the battery is charging.

Allow the phone to charge for 12 hours prior to first use. If you don’t properly charge the phone, battery

performance will be compromised.

3.

Plug the telephone line cord into the telephone jack on the bottom of the base and into a modular wall

phone jack.

NOTE:

The phone automatically defaults to touch-tone dialing. To change to pulse (rotary) dialing, see “Tone/Pulse

Dialing.” If you don’t know which type of service you have, check with the phone company.

CAUTION:

Use only the ATLINKS USA, Inc. 5-2581 power supply

that came with this unit. Using other

adapters may damage the unit.

W

ALL

M

OUNT

I

NSTALLATION

Because it is necessary to charge the handset for 12 hours prior to connecting the phone for use the first time, it

is better to leave the unit on a flat surface during initial charge before attempting to hang it on the wall.

1.

Set the ringer switch (on the handset front) to ON, and place handset in the cradle on the base.

2.

Plug one end of the power supply into the power jack on the back of the base and the other end into an electrical

outlet. The “in use/charge” indicator comes on, verifying the battery is charging.

Allow the phone to charge for 12 hours prior to

first use.

If you don't properly charge the phone, battery

performance will be compromised.

3.

Plug the telephone line cord into the telephone jack on the bottom of the base and into a modular wall

phone jack.

4.

Slip the mounting holes over the wall plate posts and slide the unit down firmly into place. (Wall plate not

included.)

5.

Place the handset in the cradle.

NOTE:

The phone automatically defaults to touch-tone dialing. To change to pulse (rotary) dialing, see “Tone/Pulse

Dialing.” If you don’t know which type of service you have, check with the phone company.

CAUTION:

Use only the ATLINKS USA, Inc. 5-2581 power supply

that came with this unit. Using other

adapters may damage the unit.

C

ORDLESS

P

HONE

B

ASICS

I

N

U

SE

I

NDICATOR

L

IGHT

The phone is ON/in use when the TALK button on the handset and the base charge/in use indicator is lit.

R

EDIAL

Press the TALK button, then press the redial button to redial the last number you called (up to 32 digits). If you get

a busy signal, and want to keep dialing the number, just press redial again (you don’t have to turn the phone off

and back on).

F

LASH

Use the flash button to activate custom calling services such as Call Waiting or call transfer, which are available

through your local phone company.

TIP:

If you press the TALK button to activate custom calling services such as call waiting, you’ll hang up the phone.

Press flash button instead.

V

OLUME

The VOLUME (left and right arrow) buttons control the volume of the handset's earpiece.

R

INGER

S

WITCH

The handset ringer switch can be set to ON or OFF. If the switch is off, the unit will not ring.

T

ONE

/P

ULSE

D

IALING

This adjustment allows you to select tone (touch-tone) or pulse (rotary) mode dialing. The phone is pre-set for

touch-tone use. To set to tone or pulse dialing:

1.

Press and hold the program button for two seconds. You will hear a beep.

2.

Press the *tone button to select Tone Dialing or press #pause to select Pulse Dialing.

3.

Press the program button again. You will hear a confirmation tone.

T

EMPORARY

T

ONE

If you have pulse (rotary) service, and want to access customer calling services that require tone dialing (such as

telebanking and long distance services), you can use this feature to make your phone temporarily touch-tone

compatible.

1.

Press the TALK button, and call the bank’s information line.

2.

Press the *tone button after your call is answered.

3.

Follow the voice instructions to complete your transaction.

4.

Hang up when finished. The phone returns to pulse (rotary) service.

P

AGING

THE

H

ANDSET

Press the page button on the base to locate a misplaced handset. When you press the page

button, the handset beeps and the indicator on the handset and the page/in use indicator on the

base blinks. Press the TALK button when you locate the handset. The page signal is one short

beep and one long beep for two minutes. To cancel the page, press the page button again.

NOTE:

You can still page the handset with the ringer off.

C

HANNEL

B

UTTON

If you ever experience any interference or don’t have clear voice quality, press the channel button on the handset

to advance to another channel.

M

EMORY

Store up to ten 20-digit telephone numbers in memory for quick dialing.

S

TORING

A

N

UMBER

IN

M

EMORY

1.

Make sure the phone is

OFF

,

and press

the memory button.

2.

Press a number key (0-9) to store the phone number in that memory location.

3.

Press memory button.

4.

Use the keypad to enter the number (up to 20 digits) you want to store in that memory location.

5.

Press the memory button again to confirm.

C

HANGING

A

S

TORED

N

UMBER

Follow the procedure in STORING A NUMBER IN MEMORY, except replace the old phone number with a new

phone number.

S

TORING

A

P

AUSE

IN

M

EMORY

Use the #pause

button to insert a pause when a delay is needed in the dialing sequence (for example, when you

must dial a 9 to get an outside line or when you must enter codes to access your bank’s information line). Each

pause counts toward the 20-digit limit.

If you need to dial 9 to get an outside line and want to store a number in memory without having to dial 9 each

time, you would:

1.


OFF

, and press the memory button.

3.

Press a number (0-9) to store the phone number in that memory location.

4.

Press memory again.

5.

Enter the number 9 (or any other appropriate number) to access an outside line.

6.

Press # pause

button.

7.

Enter the phone number you want to store in memory.

8.

Press the memory button again to confirm.

TIP:

If you need a longer pause, press the #pause button twice.

D

IALING

A

S

TORED

N

UMBER

1.


ON

by pressing the TALK button.

2.

Press the memory button.

3.

Press the number (0-9) for the desired memory location. The number dials automatically.

IMPORTANT:

If you make test calls to emergency numbers stored in memory, remain on the line and briefly

explain the reason for the call to the dispatcher. Also, it’s a good idea to make these calls in off-peak hours, such as

early morning or late evening.

C

HANGING

THE

B

ATTERY

Make sure the telephone is

OFF

before you replace battery.

1.

Remove the battery compartment door.

2.

Disconnect the cord attached to the battery pack and remove the battery pack from the

handset.

3.

Insert the new battery pack and connect the cord into the jack inside the handset.

4.

Put the battery compartment door back on.

5.

Place handset in the base to charge.

If you don’t charge the handset battery properly

(for 12 hours) when you first set up the phone and/or when you install a new battery

pack, the battery’s long-term performance will be compromised.

CAUTION:

To reduce the risk of fire or personal injury, use only the battery listed in

the instruction book.

B

ATTERY

S

AFETY

P

RECAUTIONS

•

Do not burn, disassemble, mutilate, or puncture. Like other batteries of this type, toxic

materials could be released which can cause injury.

•

To reduce the risk of fire or personal injury, use only the battery listed in the User’s Guide.

•

Keep batteries out of the reach of children.

•

Remove batteries if storing over 30 days.

NOTE:

The RBRC seal on the battery used in your ATLINKS USA product indicates that we are

participating in a program to collect and recycle Nickel Cadmium batteries throughout the United States.

Please call 1-800-8-BATTERY for information or contact your local recycling center.

H

ANDSET

S

OUND

S

IGNALS

Signal

Meaning

A long warbling tone

You have an incoming call (with ringer ON)

One short beep and one long beep

The handset is being paged

A short beep every seven seconds

Low battery warning

Three short beeps

Error tone

Two long beeps

Confirmation tone

T

ALK

B

UTTON

I

NDICATOR

L

IGHT

Signal

Meaning

Lights steadily

Phone is in use

Quickly flashing

You have an incoming call or page

Flashes every 7 seconds (phone is off)

Low battery warning

T

ROUBLESHOOTING

G

UIDE

In case of difficulty, please check the following Troubleshooting Guide before seeking service.

Problem

Solution

No dial tone

• Check installation:

Is the base power cord connected to a working outlet?

Are the in use lamps on the handset and base lit?

Is the handset in use/charge light on?

Is the telephone line cord connected to the base unit and the

wall jack?

• Disconnect the base from the wall jack and connect another

phone to the same jack. If there is no dial tone in the second

phone, the problem might be your wiring or local service.

• Is the handset out of the base unit’s range? Move closer to

the base unit.

• Make sure the battery is properly charged (12 hours).

• Is the battery pack installed correctly?

• If the phone still does not work, disconnect the power cord

and remove the battery pack. Then reconnect the power cord

and reinstall the battery pack. Place handset in the base for

10 seconds to allow it to reinitialize.

Dial tone is OK, but

• Make sure the tone/pulse setting is

can’t dial out

programmed correctly.

Handset does not ring

• Make sure the ringer switch on the handset is turned to ON.

•You may have too many extension phones on your line. Try

unplugging some phones.

•See solutions for “No dial tone.”

Cannot hear phone

• Press the VOLUME (left and right arrow) buttons to adjust

conversation

the volume to the desired listening level.

CUSTOMER: CUT ALONG DOTTED LINE.

A

CCESSORY

O

RDER

F

ORM

*Prices are subject to change without notice.

Total Merchandise

.........................................

$_______________

Sales Tax

........................................................

$_______________

We are required by law to collect the appropriate sales tax for each individual state, county, and locality to which the

merchandise is being sent.

Use VISA or Master Card or Discover preferably. Money order or check must be in U.S. currency only. No COD or Cash. All

accessories are subject to availability. Where applicable, we will ship a superseding model.

Shipping/Handling

.......................................

$_______________

Total Amount Enclosed

.................................

$_______________

Mail order form and money order or check (in U.S. currency) made payable to Thomson to:

Thomson

Mail Order Department

P.O. Box 8419

Ronks, PA 17573-8419

Name_______________________________________________________

Address_____________________________________ Apt.____________

City ________________________State________ ZIP_________________

Daytime Phone Number (

)___________________________________

____________________________________________________________________

Authorized Signature

My card expires:

Copy the number above your name on

the

Master Card.

For credit card purchases

Your complete charge card number, its expiration date and your signature are necessary to process all charge

card orders.

Copy your complete account number from your

VISA

card.

My card expires:

Copy your complete account number from your

Master Card or Discover.

To order, call

1-800-338-0376

(for accessories only) or complete this order form.

DESCRIPTION

AC power supply

5-2581

5-2581

5-2581

$19.95

Replacement battery

5-2574

5-2574

5-2574

$9.95

TALK

redial

memory

program

ringer

channel

off

on

flash

abc

2

jkl

5

tuv

8

oper

0

def

3

mno

6

wxyz

9

#

1

ghi

4

pqrs

7

*

VOL

tone

pause

+

-

TALK button

VOLUME + button

redial button

*tone button

TALK

2

5

8

0

3

6

9

#

1

4

7

*

+

-

2

3

1

4

5

program button

memory button

SEE MARKING ON BOTTOM / BACK OF PRODUCT

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

TO

PREVENT FIRE OR

ELECTRICAL SHOCK

HAZARD, DO NOT

EXPOSE THIS

PRODUCT

TO RAIN

OR MOISTURE.

THE LIGHTNING

FLASH AND ARROW

HEAD WITHIN THE

TRIANGLE IS A

WARNING SIGN

ALERTING YOU OF

“DANGEROUS

VOLTAGE” INSIDE

THE PRODUCT.

CAUTION: TO REDUCE THE

RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR

BACK). NO USER

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO

QUALIFIED SERVICE

PERSONNEL.

THE EXCLAMATION

POINT WITHIN THE

TRIANGLE IS A

WARNING SIGN

ALERTING YOU

OF

IMPORTANT

INSTRUCTIONS

ACCOMPANYING

THE PRODUCT.

CAUTION:

VOLUME - button

26928

Model 26928M

16167880 (Rev. 0 E/S)

03-10

Printed in China

page button

You experience static,

• Change channels.

noise, or fading in

• Is handset out of range? Move closer to the base.

and out

• Does the base need to be relocated?

• Charge handset battery.

• Make sure base is not plugged into an outlet with another

household appliance.

Range is shorter

• Press the channel button during the conversation to

than normal

select a new channel.

Phone dials in pulse

• Make sure the phone is set to tone dialing.

with tone service

Phone won’t dial out

• Make sure the phone is set to pulse dialing.

with pulse service

Battery will not hold a

• Be sure you are charging the battery for 12 hours; you

charge

can expect approximately seven hours of talk time.

• Check to be sure battery contacts on both the handset and

the base are making contact and are clean; free of dirt or lint.

• When the handset is placed in the base, check that the base

in use/charge light is on.

Memory Dialing

• Did you program the memory location keys correctly?

doesn’t work

• Did you follow proper dialing sequence?

• Make sure the tone/pulse setting is programmed correctly.

Unit locks up and

• If the phone still does not work, disconnect the power cord

no communication

and remove the battery pack. Then reconnect the power

between the base

cord and reinstall the battery pack. Place handset in the base

and the handset

for 10 seconds to allow it to reinitialize.

• If a power outage occurs while the handset is away from the

base, the handset must be returned to the base when the

power returns.

S

ERVICE

If trouble is experienced with this equipment, for repair or warranty information, please contact customer service

at

1-800-448-0329

. If the equipment is causing harm to the telephone network, the telephone company may

request that you disconnect the equipment until the problem is resolved.

This product may be serviced only by the manufacturer or its authorized service agents. Changes or modifications

not expressly approved by ATLINKS USA, Inc. could void the user’s authority to operate this product. For

instructions on how to obtain service, refer to the warranty included in this guide or call customer service at

1-

800-448-0329

.

Or refer inquiries to:

ATLINKS USA, Inc.

Manager, Consumer Relations

P O Box 1976

Indianapolis, IN 46206

Attach your sales receipt to the booklet for future reference or jot down the date this product was purchased or

received as a gift. This information will be valuable if service should be required during the warranty period.

Purchase date

_______________________________________________________________________________

Name of store

_______________________________________________________________________________

L

IMITED

W

ARRANTY

What your warranty covers:

•

Defects in materials or workmanship.

For how long after your purchase:

•

One year, from date of purchase.

(The warranty period for rental units begins with the first rental or 45 days from date of

shipment to the rental firm, whichever comes first.)

What we will do:

•

Provide you with a new or, at our option, a refurbished unit. The exchange unit is under

warranty for the remainder of the original product’s warranty period.

How you get service:

•

Properly pack your unit. Include any cables, etc., which were originally provided with the

product. We recommend using the original carton and packing materials.

•

”Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the

product is within the warranty period, must be presented to obtain warranty service.” For

rental firms, proof of first rental is also required.

Also print your name and address and a

description of the defect. Send via standard UPS or its equivalent to:

ATLINKS USA, Inc.

c/o Thomson

11721 B Alameda Ave.

Socorro, Texas 79927

•

Pay any charges billed to you by the Exchange Center for service not covered by the warranty.

•

Insure your shipment for loss or damage. ATLINKS accepts no liability in case of damage or loss.

•

A new or refurbished unit will be shipped to you freight prepaid.

What your warranty

does not

cover:

•

Customer instruction. (Your Owner’s Manual provides information regarding operating

instructions and user controls. Any additional information, should be obtained from your dealer.)

•

Installation and setup service adjustments.

•

Batteries.

•

Damage from misuse or neglect.

•

Products which have been modified or incorporated into other products.

•

Products purchased or serviced outside the USA.

•

Acts of nature, such as but not limited to lightning damage.

MODEL NO.

silver

$5.00

blue

PRICE*

QUANTITY

TOTAL

Please make sure that this form has been filled out completely.

ATLINKS USA, Inc.

101 West 103rd Street

Indianapolis, IN 46290

© 2003 ATLINKS USA, Inc.

Trademark(s) ® Registered

Marca(s) Registrada(s)

Telephone

line jack

Wall plate

TALK

2

5

8

0

3

6

9

#

1

4

7

*

+

-

3

2

1

# pause button

channel button

ringer switch

flash button

Product Registration:

•

Please complete and mail the Product Registration Card packed with your unit. It will make it

easier to contact you should it ever be necessary. The return of the card is not required for

warranty coverage.

Limitation of Warranty:

•

THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLETO THIS PRODUCT. ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO

VERBAL OR WRITTEN INFORMATION GIVEN BY ATLINKS USA, INC., ITS AGENTS, OR EMPLOYEES

SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.

•

REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE

REMEDY OF THE CONSUMER.

ATLINKS USA, INC. SHALL NOT BE LIABLE FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING

OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS

DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF

THE STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY

IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON

THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.

How state law relates to this warranty:

•

Some states do not allow the exclusion nor limitation of incidental or consequential

damages, or limitations on how long an implied warranty lasts so the above limitations or

exclusions may not apply to you.

•

This warranty gives you specific legal rights, and you also may have other rights that vary

from state to state.

If you purchased your product outside the USA:

•

This warranty does not apply. Contact your dealer for warranty information.

M

AKING

A

C

ALL

After initial set up, put handset in cradle on the base and charge the battery for 12 hours. To make a call:

•

Press the TALK button before you dial.

•

Press TALK or place the handset in the base to hang up.

R

ECEIVING

A

C

ALL

To answer a call, press the TALK button and begin speaking.

red

GE 26928GE1 User Guide

GE 26928GE1 Manual

GE 26928GE1 manual content summary: