GE 45132 User Manual

GE 45132 - Choice-Alert Wireless Motion Sensor Alarm System Manual

Get GE 45132 - Choice-Alert Wireless Motion Sensor Alarm System PDF manuals and user guides
UPC - 043180451323
View all GE 45132 manuals
Add to My Manuals
Save this manual to your list of manuals

GE 45132 manual content summary:

  • GE 45132 | User Manual - Page 1
    45132 Wireless Alarm System Motion Sensor User's Manual Choice ALERT™™ Control all Sensors & accessories from one location
  • GE 45132 | User Manual - Page 2
    Table of Contents Important Safeguards Introduction Assigning a Sensor to a Zone Testing a Sensor or your system Installation Erasing a Sensor from a Zone Low battery indicator Battery warnings F.A.Q.'S FCC Warning 4 5 6-7 7-8 8 8-9 10 11 12-13 14 2
  • GE 45132 | User Manual - Page 3
    or operating the Motion Sensor, please read these instructions carefully and save this manual for future reference. Congratulations The GE Choice Alert™ Wireless Alarm System is one of the most affordable and expandable wireless alarm systems available. You'll discover the system offers many
  • GE 45132 | User Manual - Page 4
    the Motion Sensor. Modifying or tampering the device or its internal components can cause a malfunction and void the Motion Sensor's warranty. 3. If you feel the Motion Sensor or any part of the Choice Alert system is not operating correctly or as described, please contact Customer Service for
  • GE 45132 | User Manual - Page 5
    , workshops, etc. When the Sensor detects motion, it will transmit a signal to the Control Center. The Zone selection and settings on the Control Center determine if an alarm or an alert sounds. Parts Check List Identify all the parts before proceeding. Motion Sensor with mounting bracket 2 - Screws
  • GE 45132 | User Manual - Page 6
    - Press the Zone button (1, 2, 3 or 4) for the Zone you want to assign to the Motion Sensor. The LED indicator for that Zone will begin to flash. Step 3 - Release the Zone button. Note: Zone 4 is for dedicated alerts only. Sensors in this Zone will not trigger an alarm or chime. Step 4 - Activate the
  • GE 45132 | User Manual - Page 7
    in front of the Motion Sensor). Testing a Sensor or your system Once all the Sensors have been assigned to Zones in the Control Center you can now test your system. Step 2 Select the Zone number 1 2 3 4 Arm 1 2 3 4 Zone Armed Power Input DC 12V -+ Mute Learn Alert Chime Off Step 1 Press
  • GE 45132 | User Manual - Page 8
    is 5-6 ft, depending on where you want to mount the Motion Sensor. Once the location is selected, before mounting you should perform a manual test to confirm the Motion Sensor is within range of Control Center. Refer to the Testing a Sensor section on pg 7. Mount the ball-head joint to the location
  • GE 45132 | User Manual - Page 9
    erased. Note: The Zone/Motion Sensor cannot be erased if: - The Zone has been triggered for an Alert or alarm. The Sensor/Zone must be reset. - There is loss of signal from the Sensor to the Control Center (such as low battery, or Sensor is out of range). - The system is armed. The Control Center
  • GE 45132 | User Manual - Page 10
    an alert then replace the battery with a new one. Note: The Sensor detection system is 'range dependant', which means Sensors located closer to the Control Center may seem to have batteries that last longer than those Sensors at a greater distance. Also, keep in mind, because the Motion Sensor is
  • GE 45132 | User Manual - Page 11
    24 months 45132 MotionSensor (1) "9V" 9 months *maximum potential life based upon usage and location WARNING! Risk of personal injury - Prolonged exposure to alarm siren may cause permanent hearing loss Battery Warning! - Remove batteries before storing the Alarm or Sensor for extended periods
  • GE 45132 | User Manual - Page 12
    . Why? A. The system can only erase entire Zones. You will need to add the other Sensors back in that Zone to the Control Center again. Q. I put the Sensor in a Zone (1, 2, 3) and it will not sound in any Alert modes. Why? A. The Motion Sensor only functions as an Alarm Sensor in Zones 1, 2, 3. It
  • GE 45132 | User Manual - Page 13
    (see pg.9 in manual). Q. If one Sensor has a low battery, will the other Sensors in the Zone (or other Zones) continue to operate? A. Yes, as long as the other Sensors have sufficient battery power, they will continue to transmit information to the Control Center and the system will operate normally
  • GE 45132 | User Manual - Page 14
    user's warranty and may conflict with both state and federal laws. The Choice Alert system complies with part 15 of the FCC rules. Operation is subject to the following conditions: 1) The Choice Alert system may not cause harmful interference. 2) The Choice Alert system with the instructions, may
  • GE 45132 | User Manual - Page 15
    a guarantee that such an event will be prevented, and users should protect themselves with proper insurance. JASCO makes no representation injuries, property damage, or other losses. Like any alarm product, including expensive commercial systems, it may be bypassed, it is subject to compromise
  • GE 45132 | User Manual - Page 16
    is a trademark of the General Electric Company and is used under license to Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114. This Jasco product comes with a 1 year limited warranty. Visit www.jascoproducts.com for details. 45132-1 01/18/08
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
45132
Choice
ALERT
Choice
ALERT
™
Control all Sensors
& accessories from
one location
™
Wireless Alarm System
Motion
Sensor
User’s Manual