GE CP9530SJSS Quick Specs
GE CP9530SJSS Manual
 |
View all GE CP9530SJSS manuals
Add to My Manuals
Save this manual to your list of manuals |
GE CP9530SJSS manual content summary:
- GE CP9530SJSS | Quick Specs - Page 1
of unit and 6" at conduit location 29-3/4" Cooktop 21-3/8" Note: 30" Ribbon cooktops are approved for use over select GE 27" and GE 30" Single Wall Ovens and Warming Drawers. Refer to cooktop and wall oven/ warming drawer installation instructions packed with product for current dimensional data - GE CP9530SJSS | Quick Specs - Page 2
this lightweight griddle, tailored to fit GE SyncBurners Keep Warm setting - Keep food warm with GE's lowest heat setting or boil water quick glance Cooktop "On" indicator light - A light lets you know when an element is active Model CP9530SJSS - Stainless steel CP9530SJSS Specification Created
-
1 -
2
 |
 |
Specificattvion Created 1/15
Listed by
Underwriters
Laboratories
IMPORTANT
: Requires a 5" free area between
the bottom of the cooktop to any combustible
material, i.e., shelving. Free area not required
when installing wall oven underneath cooktop.
Refer to installation instructions. Requires a 15"
minimum from cooktop to adjacent overhead
cabinets. Units are furnished with a 48" flexible
armored cable.
NOTE:
30" Ribbon cooktops are approved for use
over select GE 27" and GE 30" Single Wall Ovens and
Warming Drawers. Refer to cooktop and wall oven/
warming drawer installation instructions packed with
product for current dimensional data. If installed
with a GE Telescopic Downdraft System, consult both
the cooktop and downdraft installation instructions
packed with product before installing.
Cooktop gas/
electric supply may need to be re-routed to install
downdraft.
The countertop cutout requires 23-1/2"
minimum flat countertop surface and 25" minimum
total countertop depth. In addition, other clearances
to front edge of the countertop must be considered.
Before installing, consult installation instructions
packed with product for current dimensional data.
CUTOUT FILLER TRIM KIT:
A filler trim kit is
available for use if your countertop cutout is larger
than the dimension shown, up to 29-13/16" x 20-7/16".
Order JXTR32B for black or JXTR32W for white,
to reduce the cutout opening for installation of this
cooktop. These kits may be ordered from your
GE Dealer.
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
CP9530SJ
GE Café
™
Series 30" Built-In Knob Control Electric Cooktop
KW Rating
240V
9.4
208V
8.2
Amperage
240V
39.2 Amps
†
208V
39.2 Amps
†
†
Note:
Check local codes for
required breaker size
To insure accuracy, it is best to make a
template when cutting the opening in the counter
Electrical junction box 16" MIN.
below countertop
Cooktop
29-3/4"
21-3/8"
19-1/4"
28"
19-5/8" to
19-3/4"
28-1/2" to
28-5/8"
2-1/2" MIN.
Required
1-3/4" MIN.
to rear wall
13" MAX. depth of unprotected
overhead cabinets (when no
hood or microwave is installed)
30" MIN. from countertop to
unprotected cabinet (when
no hood or microwave is
installed)
15" MIN. height from countertop
to nearest cabinet (including
light rails) on both sides of
cooktop
2" MIN. clearance
to side wall from cut-out
on left sides of unit and
1-1/2" clearance on
right side of unit
3-1/4" at front of unit and
6" at conduit location
APPROXIMATE COOKING DIMENSIONS
For answers to your Monogram,
®
GE Profile
™
or GE
®
appliance questions, visit our website
at geappliances.com or call GE Answer Center
®
service, 800.626.2000.