GE DWSR483E Installation Instructions
GE DWSR483E - Appliances 7.0 cu. Ft. Electric Dryer Manual
 |
View all GE DWSR483E manuals
Add to My Manuals
Save this manual to your list of manuals |
GE DWSR483E manual content summary:
- GE DWSR483E | Installation Instructions - Page 1
described in these instructions. • Do not install or store appliance in an area where it will be exposed to water and/or weather • Install the dryer where the temperature is above 50ºF for satisfactory operation of the dryer control system. NOTE: Installation and service of this dryer requires basic - GE DWSR483E | Installation Instructions - Page 2
be given to provide adequate clearance for installation and service. 1 PREPARING FOR INSTALLATION OF NEW DRYER EXTERNAL DUCT OPENING DUCT TAPE OR DUCT CLAMP If the electric supply does not meet the above specifications, then call a licensed electrician. GROUNDING INSTRUCTIONS This dryer must be - GE DWSR483E | Installation Instructions - Page 3
Installation Instructions 1. Turn off the circuit breaker (s) (30 amp) or remove the dryer's circuit fuse at the electrical box. 2. Be sure the dryer cord the dryer life. • Accumulate lint, creating a potential fire hazard. The correct exhaust installation is YOUR RESPONSIBILITY. Problems due to - GE DWSR483E | Installation Instructions - Page 4
. A combination of lint and grease could create a fire hazard. • Do not obstruct incoming or exhausted air. THIS DRYER COMES READY FOR REAR EXHAUSTING. IF SPACE IS LIMITED, USE THE INSTRUCTIONS IN SECTION 9 TO EXHAUST DIRECTLY FROM THE SIDES OR BOTTOM OF THE CABINET. STANDARD REAR EXHAUST (Vented at - GE DWSR483E | Installation Instructions - Page 5
Instructions Never Use Transition Duct Inside the Wall or Inside the Dryer. • Avoid Resting the Duct on Sharp Objects. • ELECTRICAL CODE, ANSI/NFPA NO. 70. 8 MOBILE OR MANUFACTURED HOME INSTALLATION • Installation must conform to the MANUFACTURED HOME CONSTRUCTION & SAFETY STANDARD, TITLE 24, PART - GE DWSR483E | Installation Instructions - Page 6
: Be sure not to pull or damage the electrical wires inside the dryer when inserting the duct. EXHAUST CAN BE ADDED TO LEFT OR RIGHT SIDE DUCT TAPE BEND TAB UP 45o Through the rear opening, locate the tab in the middle of the appliance base. Lift the tab to about 45º using - GE DWSR483E | Installation Instructions - Page 7
Pub # 31-15475 11 SERVICING WARNING - LABEL ALL WIRES PRIOR TO DISCONNECTING WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION AFTER SERVICING/INSTALLATION. For servicing phone numbers for replacement parts, and other information, refer to Owner's Manual or visit our - GE DWSR483E | Installation Instructions - Page 8
Notes
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
Installation
Instructions
Electric Dryer
37
BEFORE YOU BEGIN
TOOLS YOU
WILL NEED
MATERIALS YOU WILL NEED
FOR YOUR SAFETY:
WARNING
Read these instructions completely and carefully.
PHILLIPS SCREWDRIVER
SLIP JOINT PLIERS
LEVEL
GLOVES
SAFETY GLASSES
DRYER POWER
CORD KIT
(NOT PROVIDED
WITH DRYER)
UL RATED 120/240V, 30A
WITH 3 OR 4 PRONGS.
IDENTIFY THE PLUG TYPE
AS PER THE HOUSE
RECEPTACLE BEFORE
PURCHASING LINE CORD.
4" DUCT
CLAMPS (2)
OR
4" SPRING
CLAMPS (2)
EXHAUST HOOD
3/4" STRAIN RELIEF
UL RECOGNIZED
• Use only rigid metal or flexible metal 4-in. diameter
ductwork for exhausting to the outdoors. Never
use plastic or other combustible, easy-to-puncture ductwork.
• This appliance must be properly grounded and installed
as described in these instructions.
• Do not install or store appliance in an area where it
will be exposed to water and/or weather
• Install the dryer where the temperature is above 50ºF
for satisfactory operation of the dryer control system.
4" DIA. METAL
ELBOW
•
IMPORTANT -
Save these
instructions for local inspector’s use.
•
IMPORTANT -
Observe all
governing codes and ordinances.
• Note to Installer
- Be sure to leave these instructions with
the customer.
• Note to Customer -
Keep these instructions with your Use
and Care Book for future reference.
•
Exhausting the dryer to the outdoors is strongly recom-
mended to prevent large amounts of moisture from being
blown into the room.
•
Before the old dryer is removed from service or discarded,
remove the dryer door.
•
Service information and the wiring diagram are located in
the control console.
•
Do not allow children on or in the appliance. Close
supervision of children is necessary when the appliance is
used near children.
NOTE: Installation and service of this dryer
requires basic mechanical and electrical skills.
It is your responsibility to contact a qualified
installer to make the electrical connections.
Step 1
Prepare the Area and Exhaust for Installation of
New Dryer (see section 1).
Step 2
Check and Ensure the Existing External Exhaust is
Clean (see section 1) and Meets Attached Installation
Specifications (see section 3).
Step 3
Remove the Foam Shipping Pads (see section 1).
Step 4
Move the Dryer to the Desired Location.
Step 5
Connect the Power Supply (see section 2).
Step 6
Connect the External Exhaust (see section 4).
Step 7
Level Your Dryer (see section 5).
Step 8
Check the Operation of the Power Supply
and Venting.
Step 9
Place the Owners Manual and the Installation
Instructions in a Location Where They Will Be
Noticed By the Owner.
For Alcove or Closet Installation, see section 6.
For Bathroom or Bedroom Installation, see section 7.
For Mobile or Manufactured Home see, section 8.
For side or bottom exhaust, see section 9.
Questions on Installation? Call: 1-800-GECARES (US)
or
Visit our Web site at:
www.GEAppliances.com (US)
4" DIA. METAL DUCT
(RECOMMENDED)
4" DIA. FLEXIBLE METAL DUCT
(IF NEEDED)
FLAT BLADE SCREWDRIVER
DUCT TAPE