GE GTD75GCPLDG Quick Specs
GE GTD75GCPLDG Manual
 |
View all GE GTD75GCPLDG manuals
Add to My Manuals
Save this manual to your list of manuals |
GE GTD75GCPLDG manual content summary:
- GE GTD75GCPLDG | Quick Specs - Page 1
. NOTE: Dryer wall outlet must be located within 36" of service cord entry and accessible when dryer is mounted in position. INSTALLATION INFORMATION: For complete information, see installation instructions packed with your dryer. SPECIAL INSTALLATION REQUIREMENTS ALCOVE OR CLOSET INSTALLATION - GE GTD75GCPLDG | Quick Specs - Page 2
to your Monogram, GE Café™ Series, GE Profile™ Series or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000. Specification Revised 9/17 - GE GTD75GCPLDG | Quick Specs - Page 3
/GCSL GE Dryer Vent GE® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry FOR COMPLETE INFORMATION, SEE INSTALLATION INSTRUCTIONS PACKED WITH YOUR DRYER. DUCTING MATERIALS: For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If - GE GTD75GCPLDG | Quick Specs - Page 4
GTD75GCPL/GCSL GE® 7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry FEATURES AND BENEFITS Steam Select - For the best results, customize your cycle by specifying the number of garments needing to be steamed WiFi Connect - Control and monitor your laundry from anywhere with a
-
1 -
2 -
3 -
4
 |
 |
GTD75GCPL/GCSL
GE
®
7.4 Cu. Ft. Capacity Aluminized Alloy Drum Gas Dryer With HE Sensor Dry
For answers to your Monogram, GE Café
™
Series, GE Profile
™
Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center
®
Service, 800.626.2000.
Specification Revised 9/17
EXHAUST OPTION:
When viewed from the front
of the unit, exhaust 3-way via rear, left and bottom.
Dryer is shipped exhausted to the rear. Alternate
exhausting knockouts are supplied.
GAS:
An individual, properly-grounded branch circuit,
with a three-prong grounding-type receptacle, protected
by a 15 or 20 amp circuit breaker or a time-delay fuse is
required.
GAS DRYER ELECTRIC RATING:
120V, 60Hz, 6A
GAS (BTU/HR):
22,000. Factory-equipped for
natural gas. Tested for LP gas. LP gas supply requires
a conversion kit. Check installation instructions for
correct kit and have a qualified gas technician install a
conversion kit. See dryer ducting information for proper
installation.
NOTE:
Dryer wall outlet must be located within 36" of
service cord entry and accessible when dryer is mounted
in position.
INSTALLATION INFORMATION:
For complete
information, see installation instructions packed with
your dryer.
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
SPECIAL INSTALLATION REQUIREMENTS
ALCOVE OR CLOSET INSTALLATION:
-
If your dryer is approved for installation in an alcove or closet, it will be stated on a
label on the dryer back.
-
The dryer MUST be exhausted to the outside.
-
Minimum clearances between dryer cabinet and adjacent walls or other surfaces
are: 0" either side; 1" front, top and rear
-
Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet contains
both a washer and a dryer, doors must contain a minimum of 120 sq. in. of
open area equally distributed.
-
No other fuel-burning appliance shall be installed in the same closet with a
gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
-
The dryer MUST be exhausted to the outdoors.
-
The installation must conform with the local codes, or in the absence of local
codes, with the National Electric Code and National Fuel Gas Code, ANSI
Z223 for gas dryers.
MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET
INSTALLATION:
-
Minimum clearances to combustible surfaces are: 0" both sides; 1" rear
DRYER EXHAUSTING INFORMATION:
-
Use metal duct only, vertical and horizontal ducting.