GE JEM31WF Installation Instructions
GE JEM31WF - Spacemaker II Microwave Oven Manual
 |
View all GE JEM31WF manuals
Add to My Manuals
Save this manual to your list of manuals |
GE JEM31WF manual content summary:
- GE JEM31WF | Installation Instructions - Page 1
alone or over any GE/GE Profile single electric wall oven. • For easier installation and personal safety, we recommend that two people install this microwave oven. • Unplug the microwave oven before attempting installation of this kit. • This kit is for use on models: PEB1590DMBB, PEB1590DMWW and - GE JEM31WF | Installation Instructions - Page 2
edges of the cutout. On 30″ models, allow 11⁄2″ at the top and bottom and 3″ on each side for overlap of the trim frame over the edges of the cutout. FOR INSTALLATION ABOVE A BUILT-IN OVEN: Microwave oven should be installed on a 3/8″ plywood base and supported by 2x4 or 1x2 equivalent runners on - GE JEM31WF | Installation Instructions - Page 3
loose items, including the turntable and turntable support, from the microwave oven. Carefully turn the oven upside down. Remove three screws (one from microwave oven ❒ 5 INSTALL MICROWAVE OVEN INTO CABINET A Slide the microwave oven part way into the cabinet opening. B Plug in the microwave oven - GE JEM31WF | Installation Instructions - Page 4
-head screws. Flat-Head Screws ❒ 9 REPLACE ANY LOOSE ITEMS A Your trim kit is now fully installed. Replace the turntable and turntable support that were removed from the inside of the microwave oven. B Keep these installation instructions and extra screws for future reference and need. Do not place
-
1 -
2 -
3 -
4
 |
 |
PARTS INCLUDED
NOTE:
This kit has extra screws to prevent the
technician from spending extra time locating a
replacement screw during installation.
PART
QUANTITY
❒
Trim Frame
1
❒
Bottom Duct
1
❒
Top Bracket
1
❒
Bottom Bracket
1
❒
Upper Duct
1
❒
Rear Duct
1
❒
4 mm x 14 mm
22 required
Round-Head
2 extra
Screws
❒
4 mm x 14 mm
4 required
Flat-Head
2 extra
Screws
❒
Anti-Tip Brace
1
❒
Anti-Tip Bracket
1
❒
Template
1
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Installation
Built-In Trim Kits
Instructions
JX1527
JX1530
1
❒
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT
—
Save these instructions
for local inspector’s use.
•
IMPORTANT
—
Observe all governing
codes and ordinances.
•
Note to Installer –
Be sure to leave these
instructions with the Consumer.
•
Note to Consumer –
Keep these instructions for
future reference.
•
Skill level –
Installation of this appliance requires
basic mechanical and electrical skills.
•
Completion time –
1 to 3 hours
•
Proper installation is the responsibility of the
installer.
•
Product failure due to improper installation is not
covered under the Warranty.
•
This kit is UL listed for installation alone
or over any GE/GE Profile single electric wall oven.
•
For easier installation and personal safety, we
recommend that two people install this microwave
oven.
•
Unplug the microwave oven before attempting
installation of this kit.
•
This kit is for use on models: PEB1590DMBB,
PEB1590DMWW and PEB1590SMSS.
•
Do not alter or modify any part of this kit or the
oven.
WARNING
—
This oven must
be plugged into a properly grounded 3-hole, 120V
receptacle as required by the National Electrical Code.
FOR YOUR SAFETY:
WARNING
—
Before beginning the
installation, switch power off at service panel and lock
the service disconnecting means to prevent power
from being switched on accidentally. When the
service disconnecting means cannot be locked,
securely fasten a prominent warning device,
such as a tag, to the service panel.
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com