GE SCA1000 Installation Instructions

GE SCA1000 - Profile: 1.4 cu. Ft. Advantium Microwave Oven Manual

Get GE SCA1000 - Profile: 1.4 cu. Ft. Advantium Microwave Oven PDF manuals and user guides View all GE SCA1000 manuals
Add to My Manuals
Save this manual to your list of manuals

GE SCA1000 manual content summary:

  • GE SCA1000 | Installation Instructions - Page 1
    Installation Instructions Above the Cooktop Oven JVM1490, JVM1790, SCA1000, SCA1001 Questions? Call 800-GE-CARES (800-432-2737) or Visit our Website at: ge.com BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT - Save these instructions for local inspector's use. •
  • GE SCA1000 | Installation Instructions - Page 2
    Installation Instructions CONTENTS General information Important Safety Instructions 3 Electrical Requirements 3 Hood Exhaust 4, 5 Damage - Shipment/Installation 6 Parts Included 6 Tools You Will Need 7 Mounting Space 7 C Recirculating 19-22 Attach Mounting Plate to Wall 19 Preparation of
  • GE SCA1000 | Installation Instructions - Page 3
    before beginning installation to avoid severe or fatal shock injury. CAUTION: For personal safety, the mounting surface must be capable of supporting the above the oven. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or
  • GE SCA1000 | Installation Instructions - Page 4
    Installation Instructions HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 6. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The
  • GE SCA1000 | Installation Instructions - Page 5
    Instructions NOTE: If you need to install ducts, note that the total duct length of 31⁄4″ x 10″ rectangular or 6″ diameter round duct should not exceed 140 equivalent feet. Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully. NOTE: It is important that venting
  • GE SCA1000 | Installation Instructions - Page 6
    1 (JVM1790 only) 2 1 PARTS INCLUDED ADDITIONAL PARTS PART Top Cabinet Template QUANTITY 1 1/4″ TO EDGE 12″ 4″ F. CUT OUT FOR HORIZONTAL OUTSIDE EXHAUST REAR WALL TEMPLATE Rear Wall 1 Template Installation 1 Instructions Separately 2 Packed Grease Filters Damper 1 Metal Screws
  • GE SCA1000 | Installation Instructions - Page 7
    over ranges up to 36″ wide. • If you are going to vent your oven to the outside, see Hood Exhaust Section for exhaust duct preparation. • When installing the oven beneath smooth, flat cabinets, be careful to follow the instructions on the top cabinet template for power cord clearance. • The depth
  • GE SCA1000 | Installation Instructions - Page 8
    FROM THE CARTON/REMOVING THE MOUNTING PLATE 1 Remove the box containing the installation instructions, filters, exhaust adaptor, damper and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven. 2 Fold back all 4 carton flaps fully against carton sides. Then carefully
  • GE SCA1000 | Installation Instructions - Page 9
    Installation Instructions C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position - cabinets may have decorative trim that interferes with the oven installation. Remove the decorative trim to install the oven properly and to make it level. THE OVEN MUST BE LEVEL. Use a level to make
  • GE SCA1000 | Installation Instructions - Page 10
    Installation Instructions D. ALIGNING THE WALL PLATE Hole A Draw a Vertical Line on Wall with the stud. It is important to use at least one wood screw mounted firmly in a stud to support the weight of the oven. Set the mounting plate aside. 4 Drill holes on the circles. If there is a stud, drill
  • GE SCA1000 | Installation Instructions - Page 11
    Installation Instructions 2 INSTALLATION TYPES (Choose A, B or C) This oven is designed for adaptation to the following 3 types of ventilation: A. Outside Top Exhaust (Vertical Duct) B. Outside Back Exhaust (Horizontal Duct) C. Recirculating (Non-Vented Ductless) NOTE: This oven is shipped
  • GE SCA1000 | Installation Instructions - Page 12
    Installation Instructions A OUTSIDE TOP EXHAUST (Vertical Duct) INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Install Adapter A4. Mount Oven A5. Adjust Exhaust Adaptor A6. Connect Ductwork A1. ATTACH THE MOUNTING PLATE TO THE WALL To use toggle bolts:
  • GE SCA1000 | Installation Instructions - Page 13
    Installation Instructions A2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. A4. MOUNT THE OVEN • Read the instructions on the TOP
  • GE SCA1000 | Installation Instructions - Page 14
    SCA1000, and SCA1001. 7 Tighten the outer two screws to the top of the oven. (While tightening screws, hold the oven in place against the wall and the top cabinet.) 1 Extend the house duct down to connect to the exhaust adaptor. 2 Seal exhaust duct joints using duct tape. 8 Install grease filters
  • GE SCA1000 | Installation Instructions - Page 15
    Installation Instructions B OUTSIDE BACK EXHAUST (Horizontal Duct) INSTALLATION OVERVIEW B1. Prepare Rear Wall B2. Attach Mounting Plate to Wall B3. Prepare Top Cabinet B4. Adjust Blower B5. Mount the Oven B1. PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST You need to cut an opening in the rear
  • GE SCA1000 | Installation Instructions - Page 16
    Installation Instructions FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. Back of Oven Back of Oven
  • GE SCA1000 | Installation Instructions - Page 17
    . Exhaust Adaptor Damper (hinge side up) Slide exhaust adaptor into guides on oven rear. Back of Oven Screws Locking Tabs Guides Push in securely until it is in the lower locking tabs. Take care to assure the damper hinge is installed so that it is at the top and that the damper swings freely
  • GE SCA1000 | Installation Instructions - Page 18
    Installation Instructions B5. MOUNT THE OVEN FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of
  • GE SCA1000 | Installation Instructions - Page 19
    Installation Instructions C RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Adjust Blower C4. Mount the Oven C5. Install Charcoal Filter (not supplied) C1. ATTACH THE MOUNTING PLATE TO THE WALL 3 Place the mounting plate
  • GE SCA1000 | Installation Instructions - Page 20
    Installation Instructions C3. ADAPTING BLOWER FOR RECIRCULATION NOTE: The exhaust adaptor with damper is not needed for recirculating models. You may want to save them for possible future use. 1 Remove and save screws that hold blower plate to the oven. Blower Plate Screws 3 Carefully pull out the
  • GE SCA1000 | Installation Instructions - Page 21
    Front Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal, use the nylon grommet around the power
  • GE SCA1000 | Installation Instructions - Page 22
    on two side support tabs and in front of the right rear tab. When properly installed, the wire mesh of the filter should be visible from the front. 8 Install grease filters. See the Owner's Manual packed with the oven. 5 Replace the grille and the 2 top screws. 6 Close the door and replace left
  • GE SCA1000 | Installation Instructions - Page 23
    the Owner's Manual. 2. Remove all packing material from the oven. 3. Install turntable and wheeled ring in cavity. 4. Replace house fuse or turn breaker back on. 7. KEEP INSTALLATION INSTRUCTIONS FOR THE LOCAL INSPECTOR'S USE. 5. Plug power cord into a dedicated 15 to 20 amp electrical outlet
  • GE SCA1000 | Installation Instructions - Page 24
    49-40453 (06-05 JR) 24 Printed in Korea
  • GE SCA1000 | Installation Instructions - Page 25
    Instrucciones Horno para colocar de instalación encima de la estufa JVM1490, JVM1790, SCA1000 y SCA1001 ¿Preguntas? Llame 800-GE-CARES (800-432-2737) o visite nuestra página en la red en: ge.com ANTES DE EMPEZAR Lea estas instrucciones completa y cuidadosamente. • IMPORTANTE - Guarde estas
  • GE SCA1000 | Installation Instructions - Page 26
    Instrucciones de instalación CONTENIDO Información general Instrucciones de seguridad importantes 27 Requisitos eléctricos 27 Campana de escape 28, 29 Daños - Envío / Instalación 30 Partes incluidas 30 Herramientas que necesitar 31 Espacio de montaje 31 C Recirculación 43-46 Cómo adherir
  • GE SCA1000 | Installation Instructions - Page 27
    debe estar conectado a un circuito de suministro del voltaje y frecuencia apropiados. El tamaño del alambre debe conformarse a los requisitos del National Electric Code o al código local en efecto para este índice de kilovatios. El cable eléctrico de alimentación y el interruptor deberán llevarse
  • GE SCA1000 | Installation Instructions - Page 28
    12 pies 12 pies (redondo de 6″) x (1) = 12 pies Adaptador de transición 5 pies de rectángulo a redondo* x (1) = 5 pies La longitud de las partes de los conductos equivalentes está basada en pruebas reales y reflejan los requisitos para lograr una buena ventilación con cualquier campana de
  • GE SCA1000 | Installation Instructions - Page 29
    án ser cortadas para que encajen, usando las tijeras de corte, para permitir el movimiento libre del regulador de tiros. 29 La longitud de las partes de conductos equivalentes está basada en pruebas reales y reflejan los requisitos para lograr una buena ventilación con cualquier campana de escape.
  • GE SCA1000 | Installation Instructions - Page 30
    28 x 25⁄8″) 1 (JVM1790 Sólo) Arandela aislante de 2 nilón (para gabinetes metálicos) Adaptador del escape 1 PARTES INCLUIDAS PARTES ADICIONALES PART CANTIDAD Plantilla para 1 el gabinete superior 1/4″ TO EDGE 12″ 4″ F. CUT OUT FOR HORIZONTAL OUTSIDE EXHAUST REAR WALL TEMPLATE
  • GE SCA1000 | Installation Instructions - Page 31
    2″ 66″ o más desde el piso hasta la parte superior del horno NOTAS: El extremo del fondo del entre el horno y los min. gabinetes. Su Manual del Propietario contiene Protector posterior de salpicaduras el del conducto de escape. • Cuando se instale el horno debajo de gabinetes de fondos lisos
  • GE SCA1000 | Installation Instructions - Page 32
    que protege el frente del horno. 2 Pliegue hacia atrás las alas de la caja. Luego, cuidadosamente ruede el horno hasta que quede apoyado sobre la parte superior. El horno deberá descansar sobre la espuma de poliestireno. B. CÓMO ENCONTRAR LOS POSTES DE VIGA EN LA PARED Postes de viga en la pared
  • GE SCA1000 | Installation Instructions - Page 33
    para cerciorarse de que el fondo del gabinete está nivelado. Si los gabinetes tienen un saliente frontal solamente, sin marco posterior o lateral, instale el plato de montaje a la misma distancia de la profundidad del saliente. Este mantendrá el horno nivelado. 1 Mida la profundidad interna del
  • GE SCA1000 | Installation Instructions - Page 34
    Instrucciones de instalación D. CÓMO ALINEAR EL PLATO DE MONTAJE SOBRE LA PARED Agujero A TRACE UNA LÍNEA VERTICAL EN LA PARED A PARTIR DEL CENTRO DEL GABINETE SUPERIOR Agujero B Agujero C PRECAUCIÓN: Use guantes de protección para evitar cortaduras en sus dedos con los extremos filosos. Area E
  • GE SCA1000 | Installation Instructions - Page 35
    ÓN (SIN CONDUCTO DE VENTILACIÓN) Ver página 43 35 Un Kit de accesorios de filtro de carbonilla es necesario para el sistema sin ventilación. (Consulte su Manual del Propietario para obtener el número del kit.)
  • GE SCA1000 | Installation Instructions - Page 36
    PERSPECTIVA GENERAL DE LA INSTALACIÓN A1. Como adherir el plato de montaje a la pared A2. Prepare el gabinete superior A3. Instale el del gabinete. PRECAUCIÓN: Tenga cuidado de evitar pellizcar sus dedos entre la parte posterior del plato de montaje y la pared. 4 Apriete todos los tornillos
  • GE SCA1000 | Installation Instructions - Page 37
    extremo inferior posterior en dos orejillas inferiores del plato de montaje. Adaptador de escape Plato del calefactor Parte posterior del horno 1 Coloque el horno en su posición vertical, con la parte superior hacia arriba. 2 Inserte las orejillas en cada lado del regulador de tiro en los agujeros
  • GE SCA1000 | Installation Instructions - Page 38
    Tornillos autoalineables (1⁄4″-28 x 31⁄4″) en JVM1490, SCA1000, y SCA1001. 7 Apriete los dos tornillos exteriores hacia la parte de arriba del horno. (Mientras aprieta los usando cinta adhesiva de conductos. 8 Instale los filtros de grasa. Ver el Manual del Propietario que viene con el horno. 38
  • GE SCA1000 | Installation Instructions - Page 39
    Instrucciones de instalación B ESCAPE POSTERIOR EXTERNO (Conducto horizontal) PERSPECTIVA GENERAL DE LA INSTALACIÓN B1. Prepare la pared posterior B2. Pegue el plato de montaje a la pared B3. Prepare el gabinete superior B4. Ajuste el calefactor
  • GE SCA1000 | Installation Instructions - Page 40
    contra la pared y de que el plato esté centrado apropiadamente debajo del gabinete. PRECAUCIÓN: Tenga cuidado de evitar pellizcar sus dedos entre la parte posterior del plato de montaje y la pared. 4 Apriete todos los tornillos. Tire del plato en dirección opuesta a la pared para ayudar a apretar
  • GE SCA1000 | Installation Instructions - Page 41
    las orejillas de cierre inferiores. Tanga cuidado de asegurarse de que la bisagra del regulador de tiro esté instalada de forma que esté en la parte superior y que el regulador de tiro gire libremente. 11 Asegure el adaptador de escape al horno con los dos tornillos metálicos de bronce que
  • GE SCA1000 | Installation Instructions - Page 42
    y Tornillos autoalineables (1⁄4″-28 x 31⁄4″) en JVM1490, SCA1000, y SCA1001. 7 Apriete los dos tornillos exteriores hacia la parte de arriba del horno. (Mientras aprieta los tornillos, del fondo del gabinete. 8 Instale los filtros de grasa. Ver el Manual del Propietario que viene con el horno. 42
  • GE SCA1000 | Installation Instructions - Page 43
    GENERAL DE LA INSTALACIÓN C1. Pegue el plato de montaje a la pared C2. Prepare el gabinete superior C3. Ajuste el calefactor C4. Monte el horno C5. Instale gabinete. PRECAUCIÓN: Tenga cuidado de evitar pellizcar sus dedos entre la parte posterior del plato de montaje y la pared. 4 Apriete todos los
  • GE SCA1000 | Installation Instructions - Page 44
    para posibles usos futuros. 1 Remueva y guarde los tornillos que sostienen el plato del calefactor en el horno. Tornillos del plato del calefactor Parte posterior del horno 2 Deslice el plato calefactor por debajo de su reborde de retención. Remueva y guarde los tornillos que sostienen el motor
  • GE SCA1000 | Installation Instructions - Page 45
    en el portador de tornillo inferior derecho en la parte posterior del horno. 7 Reemplace el plato calefactor con los tornillos removidos en el Paso 1. Tornillos del plato calefactor Parte posterior del horno Tornillo del motor del calefactor C4. MONTAJE DEL HORNO
  • GE SCA1000 | Installation Instructions - Page 46
    (1⁄4″-28 x 31⁄4″) en JVM1490, SCA1000, y SCA1001. 7 Apriete los dos tornillos exteriores hacia la parte de arriba del horno. (Mientras aprieta malla del filtro debería estar visible desde el frente. 8 Instale los filtros de grasa. Ver el Manual del Propietario que viene con el horno. 5 Remplace la
  • GE SCA1000 | Installation Instructions - Page 47
    un tomacorriente exclusivo de 15 a 20 amperios. Cerciórese de que existe una conexión a tierra apropiada 2. Remueva todos los materiales de embalaje del horno. 3. Instale el aro rotatorio y con ruedas en la cavidad. 4. Reemplace el fusible de la casa o encienda de nuevo el interruptor. 6. Lea el
  • GE SCA1000 | Installation Instructions - Page 48
    49-40453 (06-05 JR) Printed in Korea Impreso en Corea
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Installation
Instructions
Questions? Call 800-GE-CARES (800-432-2737)
or
Visit our Website at:
ge.com
READ CAREFULLY.
KEEP THESE INSTRUCTIONS
.
Read these instructions completely and carefully.
•
IMPORTANT
–
Save these
instructions for local inspector’s use.
•
IMPORTANT
–
Observe all
governing codes and ordinances.
•
Note to Installer
–
Be sure to leave these
instructions with the Consumer.
BEFORE YOU BEGIN
•
Note to Consumer
–
Keep these
instructions for future reference.
•
Skill level
– Installation of this appliance requires
basic mechanical and electrical skills.
•
Proper installation is the responsibility of the installer.
•
Product failure due to improper installation is not
covered under the Warranty.
Above the
Cooktop Oven
JVM1490, JVM1790, SCA1000, SCA1001
LA SECCIÓN EN ESPAÑOL
EMPIEZA EN LA PÁGINA 25.