Genie ChainLift 600 Owner's Manual
Genie ChainLift 600 Manual
 |
View all Genie ChainLift 600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Genie ChainLift 600 manual content summary:
- Genie ChainLift 600 | Owner's Manual - Page 1
/1042 GARAGE DOOR OPENERS Installer: Leave this manual with homeowner. Homelink® is a registered trademark of Johnson Controls Technology Company. Car2U® is a registered trademark of Lear Corporation. © The Genie Company 2010. X900-745 PN# 3642036534, 5/18/2011 REV.2 Includes INTELLICODE® Remote - Genie ChainLift 600 | Owner's Manual - Page 2
repair or adjust springs or anything to which door spring parts are fastened, such as, wood blocks, steel brackets, cables or other like items. Installations, repairs and adjustments must be done by a trained door system technician using proper tools and instructions. PN# 3642036534, 02/26/2010 REV - Genie ChainLift 600 | Owner's Manual - Page 3
TROUBLESHOOTING GUIDE - POWER HEAD LED . . . . . 28 TRANSMITTER COMPLIANCE STATEMENT 29 WARRANTY 30 *Opener MUST be installed with the included Wall Console. OPENER FEATURES INTELLICODE® Rolling Code Security System. An electronic rolling code system that enhances the security of the door opener - Genie ChainLift 600 | Owner's Manual - Page 4
an existing door opener with a new one, however, if this will be the first opener installed there are some pre-installation issues which need to be addressed. They are as follows: The Genie Company recommends that you read and fully understand all information and instructions contained herein - Genie ChainLift 600 | Owner's Manual - Page 5
SECTIONAL DOOR INSTALLATION 5 Pg. 19 1 Pg. 13 TYPICAL SUPPORT BRACKET (NOT PROVIDED) FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 2 Pg. 12-13 ADDED HEADER BRACKET MOUNTING BOARD BRACES POWER CORD (APPROX. 45 IN.) TO 120V GROUNDED OUTLET EXTENSION SPRING OR TORSION SPRING NOTE: This opener - Genie ChainLift 600 | Owner's Manual - Page 6
garage door. Death or serious injury can result. • Never let ch ld walk or run under moving do.or. • Never let ch ld use door opener controls. •Always keep moving door in sight. • If person is pinned, push control button or use emergency release. • Test door opener monthly: Re e to you owne s manual - Genie ChainLift 600 | Owner's Manual - Page 7
SELF DRILLING SCREW - 1/4''-20 x 3/4'' DOOR BRACKET HEX BOLT - 5/16''-18 x #10-16 x 1- 1/4'' WIRE NUT (GREY) REMOTE WITH BATTERY Safe-T-Beam® SOURCE/SENSOR & WIRE SET PARTS? Please call toll free - 1.800.354.3643 DO NOT RETURN TO POINT OF PURCHASE. IMPORTANT! - Information needed when calling • Model - Genie ChainLift 600 | Owner's Manual - Page 8
1-PIECE RAIL HARDWARE ASSEMBLED VIEW FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM Power Cord Carriage Assembly Rail with chain Tensioner CHAIN H eCepvanre CGo aHsusjnueStSmPneeRrniosNomsGu It p TjeuEmrNyndoSe IODys aeNaca h n d s T SmboromaneuNdtndgotcoCtubosuen oeafcotdr s Chain - Genie ChainLift 600 | Owner's Manual - Page 9
If you have questions or do not understand an instruction, call The Genie Company or an authorized Genie® Dealer.) 2. Install only on a properly balanced sectional garage door. An improperly balanced door could cause severe injury. Have a trained door system technician make repairs or adjustments to - Genie ChainLift 600 | Owner's Manual - Page 10
CHAIN DRIVE RAILS Chain Rail A End Rail B Wire Tie(s) BELT DRIVE RAILS Belt Rail A B Center Rail Center Rail End Rail Rail Assembly for BELT DRIVE OPENER NOTE: For split rail clamps, nuts, and bolts locate Bag 0 from Box 1. 3. Remove the two rail sections that are not connected to the belt and - Genie ChainLift 600 | Owner's Manual - Page 11
. If you have not, remove all ropes and/or cables and disable garage door lock NOW before continuing with installation (Fig. 1-8). Set assembled power head and rail aside. Begin with Section 2 INSTALLATION. Assembly for BELT DRIVE OPENER NOTE: For power head and rail assembly locate Bag 1 from Box - Genie ChainLift 600 | Owner's Manual - Page 12
HERE TO FLOOR TRACK NOTE: If header bracket location needs to be above header for garage door opening, you need to add a "mounting surface." A 2" x 6" board securely attached (board and fasteners not included) to wall studs on either side of your mark is sufficient ( - Genie ChainLift 600 | Owner's Manual - Page 13
(Fig. 2-5). • Support power head on step open ceilings, straps may attach directly to joists or trusses. Depending on the garage construction, extra framing material (not provided) which may be required should be installed Carefully raise and lower door manually. Ensure door does not contact any - Genie ChainLift 600 | Owner's Manual - Page 14
, fiberglass, and sheet metal must be properly braced before mounting door opener. Contact door manufacturer or distributor for a bracing kit. The Genie Company is not responsible for damage caused due to improperly braced door. NOTE: For door bracket and bolts locate Bag 4 from Box 2. 1. Finding - Genie ChainLift 600 | Owner's Manual - Page 15
Verify there is NO power to the opener before installing wall console wires and wall console. CAUTION above floor to prevent small children from operating door. • It must be away from any moving parts. (You should NOT be able to reach the garage door while standing at Wall Console.) • Wall Console - Genie ChainLift 600 | Owner's Manual - Page 16
manual. - Stick label on wall near wall console. FIG. 3-4 Mounting Wall Console. Vacation Locking Switch - LOCK disables controls after 1 door is completely closed - UNLOCK allows controls to work normally Door Control "Open/Close" Button - Open and closes door from 2 inside garage 3 Independent - Genie ChainLift 600 | Owner's Manual - Page 17
cord-UNPLUG IT NOW! NOTE: The opener will not close the door automatically unless the Safe-T-Beam® System is installed. NOTE: For Safe-T-Beam®, screws, wire, and insulated staples locate items and Bag 8 from Box 3. 1. Mounting brackets. • Mark both sides of garage door frame or wall no higher than - Genie ChainLift 600 | Owner's Manual - Page 18
Beam® wire to power head wire terminal. • Route Safe-T-Beam® wires through wire guide. - Insert wire into terminal holes and lightly press in the orange locking clips above as the power head clips and body (Fig. 4-9). • Do not install the white (lamp) cover at this time. (Power Head With Rear Cover - Genie ChainLift 600 | Owner's Manual - Page 19
cut off by people or obstacle, the garage door will reverse automatically to its fully opened position. (Meanwhile, the opener light will keep blinking until door moves to its fully opened position.) 4. If the Safe-T-Beam® System fails, loses power, or is installed improperly, you will have to press - Genie ChainLift 600 | Owner's Manual - Page 20
normally. Unless limits are being reset do not press set limit buttons. LED Indicator Light Open Open Set Limit Travel Limit Button Up Force OPEN Control Adjustment To Garage Door SET LEARN MANUAL LIMIT FORCE SET Learn Code CODE Button Close Travel Limit Close CLOSE Down Force Set - Genie ChainLift 600 | Owner's Manual - Page 21
installation instructions for the standard emergency release kit. 3. Test for correct operation of emergency release kit. Keyed Emergency Release Operation Instructions • Place key in slot. • Rotate and hold key while lifting garage door 1 to 2 inches. • Release key and continue opening garage door - Genie ChainLift 600 | Owner's Manual - Page 22
settings MUST BE COMPLETED before testing. 1. Testing. • Open garage door using wall button. - Place a 2" x 4" board (laid flat) under center of garage door opening (Fig. 6-6). • Close door using wall button. • When door contacts board, the door must stop (within 2 seconds) and reverse direction - Genie ChainLift 600 | Owner's Manual - Page 23
on power head. LED Indicator Light Open Open Set Limit Travel Limit Button Up Force OPEN Control Adjustment NOTE: The door will stop automatically at the fully open or fully closed position. To Garage Door SET LOST OR STOLEN REMOTE LEARN MANUAL LIMIT FORCE 1. Clear memory. • Press and - Genie ChainLift 600 | Owner's Manual - Page 24
clip. (The visor clip may come already installed.)You will have to install the visor clip if you choose to attach your remote to the car visor. • Slide visor clip into back of remote control. - It will snap into place (Fig. 8-3). Slide out FIG. 8-1 Open battery cover. - and + polarity marks FIG - Genie ChainLift 600 | Owner's Manual - Page 25
garage door automatically or manually if door is improperly balanced or springs are broken. - CONTACT A TRAINED DOOR SYSTEM TECHNICIAN. 2. Contact reverse. • Place a 2" x 4" board laid flat on floor. - In center of garage door opening. • Close door by using wall button or remote control. - Door - Genie ChainLift 600 | Owner's Manual - Page 26
para referencia. Schéma de câblage de l'ouvreur. Ce schéma de câblage est indiqué à titre de référence uniquement. WARNING ADVERTENCIA AVERTISSEMENT Opening Cover May Cause Electric Shock. Abrir la tapa puede causar choques eléctricos. L'ouverture du couvercle peut entraîner des chocs électriques - Genie ChainLift 600 | Owner's Manual - Page 27
See section 6 ). • WARNING: If you suspect a problem with the garage door hardware or springs, contact an authorized Genie® Dealer or a trained door system technician, or contact The Genie Company at 1-800-35-GENIE. Door opener starts for no reason. • Was a remote control lost or stolen? Erase all - Genie ChainLift 600 | Owner's Manual - Page 28
chain/belt tension (See section 1 ). - Contact The Genie Company at 1-800-35-GENIE • Contact Genie® authorized dealer for service • Wait until Thermal Protector cools and resets. NOTE: The 5 BLINKS pattern will remain blinking until the next opener activation. If the Thermal Protector does not reset - Genie ChainLift 600 | Owner's Manual - Page 29
TRANSMITTER COMPLIANCE STATEMENT Transmitters comply with all United States and Canadian legal requirements as of the date of manufacture. No warranty is made that they comply with all legal requirements of any other jurisdiction. If transmitters are to be used in another country, the importer must - Genie ChainLift 600 | Owner's Manual - Page 30
or reconditioned parts, or a new or reconditioned Product of the same or similar design There are no established informal dispute resolution procedures of the type described in the Magnuson-Moss Warranty Act PURCHASER: INSTALLATION ADDRESS: DATE PURCHASED: OPENER MODEL: REMOTE CONTROL MODEL: DEALER
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
 |
 |
Models 1022/1024/1042
GARAGE DOOR OPENERS
Includes INTELLICODE
®
Remote Control
Safe-T-Beam
®
System must be installed to close door.
For use only with sectional doors. Your Residential
Opener comes with a Rail Assembly which is standard
for up to a 7 foot high door.
Homelink
®
and Car2U
®
compatible
For Answers and Assistance:
1.800.354.3643
or visit www.geniecompany.com
SAVE THIS MANUAL FOR FUTURE REFERENCE
Installer:
Leave this manual
with homeowner.
PN# 3642036534,
5/18/2011
REV.2
Homelink
®
is a registered trademark of
Johnson Controls Technology Company.
Car2U
®
is a registered trademark of
Lear Corporation.
© The Genie Company 2010.
X900-745
ALWAYS AT YOUR COMMAND