Genie QuietLift 800 Owner's Manual

Genie QuietLift 800 Manual

Get Genie QuietLift 800 PDF manuals and user guides View all Genie QuietLift 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Genie QuietLift 800 manual content summary:

  • Genie QuietLift 800 | Owner's Manual - Page 1
    . © GMI Holdings, Inc. d/b/a The Genie Company PN# 37026500123, 5/15/2009 ALWAYS AT YOUR COMMAND Models 2022/2024/2042 GARAGE DOOR OPENERS Includes: 2-Bulb Light System Wall Console Includes INTELLICODE® Remote Control Safe-T-Beam® System must be installed to close door. For use only with sectional
  • Genie QuietLift 800 | Owner's Manual - Page 2
    , repair or adjust springs or anything to which door spring parts are fastened, such as, wood blocks, steel brackets, cables or other like items. Installations, repairs and adjustments must be done by a trained door system technician using proper tools and instructions. PN# 37026500123 05/15/2009
  • Genie QuietLift 800 | Owner's Manual - Page 3
    22 7 PROGRAMMING REMOTE CONTROLS 23 8 BATTERY/VISOR CLIP INSTALLATION 24 9 LIGHT BULB AND LENS INSTALLATION 24 SAFETY INSTRUCTIONS 25 MAINTENANCE & TROUBLESHOOTING 10 ROUTINE MONTHLY MAINTENANCE 25 WIRING DIAGRAM 26 TROUBLESHOOTING GUIDE - OPENER 27 TROUBLESHOOTING GUIDE - POWER HEAD LED
  • Genie QuietLift 800 | Owner's Manual - Page 4
    how you will be mounting the power head. It is possible that ceiling joists may not be in the position needed with respect to the garage door opener. It may be necessary to add an additional bracket and fasteners (not included with your new door opener kit). (Refer to Section 2.) 2 Check the wall
  • Genie QuietLift 800 | Owner's Manual - Page 5
    SECTIONAL DOOR INSTALLATION 5 Pg. 19 1 Pg. 13 TYPICAL SUPPORT BRACKET (NOT PROVIDED) FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM 2 Pg. 12-13 ADDED HEADER BRACKET MOUNTING BOARD BRACES POWER CORD (APPROX. 45 IN.) TO 120V GROUNDED OUTLET EXTENSION SPRING OR TORSION SPRING NOTE: This opener
  • Genie QuietLift 800 | Owner's Manual - Page 6
    Installation Manual for assembly steps. Procéder selon les instructions stipumléoenstadgaenàs sleuimvraen.uel d'installation pour les étapes de Box Contents Sheet Adjustable wrench Wire strippers 1/4", 7/16", 3/8" and 1/2" Sockets Hammer Child can be pinned under automatic garage door. Death
  • Genie QuietLift 800 | Owner's Manual - Page 7
    - 5/16'' x 2'' SELF DRILLING SCREW - 1/4 -20 x 3/4'' DOOR BRACKET HEX BOLT - 5/16 -18 x 3/4'' SELF LOCKING NUT - BRACKET PHILLIPS HEX SCREW - #10-16 x 1- 1/4'' WIRE NUT (GREY) REMOTE WITH BATTERY Safe-T-Beam® SOURCE/SENSOR & WIRE SET LIGHT COVER - WHITE QUANTITY PARTS? Please call toll free - 1.800
  • Genie QuietLift 800 | Owner's Manual - Page 8
    crtoTCitubrioEorsuennntrtoseaf.roceotdr r Chain Header Bracket Clevis Pin, Long & Cotter Pin 3-PIECE RAIL HARDWARE ASSEMBLED VIEW Carriage Slide Power Head Release Knob Belt Clamp Rail with belt BELT Belt Carriage Slide Power Cord Rail with chain Rail Clamps CHAIN Tensioner Rail Clamp
  • Genie QuietLift 800 | Owner's Manual - Page 9
    connected to the garage door before installing opener. 4. Where possible, install the door opener 7 feet or more above the floor. For products having an emergency release, mount the emergency release 6 feet above the floor. 5. Do NOT connect the opener to source of power until instructed to do so
  • Genie QuietLift 800 | Owner's Manual - Page 10
    to the rail sections, securely tighten the bolts and nuts. CHAIN DRIVE RAILS Chain Rail A End Rail B Wire Tie(s) BELT DRIVE RAILS Belt Rail A Tensioner Pulley B Center Rail Chain Tensioner Pulley Center Rail End Rail Rail Assembly for BELT DRIVE OPENER NOTE: For split rail clamps, nuts, and bolts
  • Genie QuietLift 800 | Owner's Manual - Page 11
    have not, remove all ropes and/or cables and disable garage door lock NOW before continuing with installation (Fig. 1-8). Set assembled power head and rail aside. Begin with Section 2 INSTALLATION. Assembly for BELT DRIVE OPENER NOTE: For power head and rail assembly locate Bag 1 from Box 1. NOTE
  • Genie QuietLift 800 | Owner's Manual - Page 12
    2 OPENER INSTALLATION HEADER AND DOOR MOUNTING BRACKETS: WARNING Header bracket must be fastened to garage framing. Do NOT fasten to drywall, particle board, plaster or other such materials. 1. Finding header bracket mounting location. • Close garage door. - Use a pencil and level. a) Mark center of
  • Genie QuietLift 800 | Owner's Manual - Page 13
    door manually. Ensure door does not contact any section of power head or rail. • Check that rail clamp bolts and nuts are tight. • DO NOT PLUG OPENER IN YET! HEADER BRACKET VIEW FROM ABOVE (not to scale) NO NO YES / SÍ / OUI FIG. 2-4 Position assembly and align. CLEVIS PIN COTTER PIN (Chain
  • Genie QuietLift 800 | Owner's Manual - Page 14
    , fiberglass, and sheet metal must be properly braced before mounting door opener. Contact door manufacturer or distributor for a bracing kit. The Genie Company is not responsible for damage caused due to improperly braced door. NOTE: For door bracket and bolts locate Bag 4 from Box 2. 1. Finding
  • Genie QuietLift 800 | Owner's Manual - Page 15
    from operating door. • It must be away from any moving parts. (You should NOT be able to reach the garage door while standing plus) terminal. - White wire to the - (minus) terminal. FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM Wire from power head to Wall Control WCoanlltrol Separate entry door
  • Genie QuietLift 800 | Owner's Manual - Page 16
    the center of this manual. - Stick label on wall near Wall Control. Vacation Locking Switch - LOCK disables controls after 1 door is completely closed - UNLOCK allows controls to work normally Door Control "Open/Close" Button - Open and closes door from 2 inside garage 3 Independent Light Control
  • Genie QuietLift 800 | Owner's Manual - Page 17
    plugged in the power cord-UNPLUG IT NOW! NOTE: The opener will not close the door automatically unless the Safe-T-Beam® System is installed. NOTE: For Sensors, screws, wire, and insulated staples locate items and Bag 8 from Box 3. 1. Mounting brackets. • Mark both sides of garage door frame or wall
  • Genie QuietLift 800 | Owner's Manual - Page 18
    Attach Safe-T-Beam® wire to power head wire terminal. • Route Safe-T-Beam® wires through wire guide on power head. - Insert wire into • Do not install the white (lamp) cover at this time. NOTE: Safe-T-Beam® alignment check must be performed following connection to electrical power (see page 19
  • Genie QuietLift 800 | Owner's Manual - Page 19
    . • DO NOT remove motor cover. All work performed on motor must be done by a trained door system technician. FIG. 5-1 Connect to power. Motor Cover Screws CAUTION • Check local building codes to make sure that you are not required to have your garage door opener permanently wired, with circuit
  • Genie QuietLift 800 | Owner's Manual - Page 20
    Force Transmitter Programming Limit Controls location on power head. LED Indicator Light Open Open Set Limit Travel Limit Button Up Force OPEN Control Adjustment To Garage Door SET LEARN MANUAL LIMIT FORCE SET A) ENGAGE CHAIN/BELT CONNECTOR TO CARRIAGE 1. Press and hold the "Close
  • Genie QuietLift 800 | Owner's Manual - Page 21
    Carriage Lock can be manually engaged or disengaged. • To disengage Carriage Lock - Pull handle downward opener power head. • To engage Carriage Lock - Pull handle towards door. DOOR UNLOCK LOCK TO RELEASE PULL TOWARD THE OPENER TO RECONNECT PULL TOWARD DOOR FIG. 6-3 Engage/Disengage Carriage
  • Genie QuietLift 800 | Owner's Manual - Page 22
    -T-Beam® System is installed. CONTACT REVERSE TEST The force adjustments and limit switch settings MUST BE COMPLETED before testing. 1. Testing. • Open garage door using Wall Control. - Place a 2" x 4" board (laid flat) under center of garage door opening (FIG. 6-5). • Close door using Wall Control
  • Genie QuietLift 800 | Owner's Manual - Page 23
    . Limit controls location on power head. LED Indicator Light Open Open Set Limit Travel Limit Button Up Force OPEN Control Adjustment NOTE: The door will stop automatically at the fully open or fully closed position. To Garage Door SET LOST OR STOLEN REMOTE 1. Clear memory. • Press and
  • Genie QuietLift 800 | Owner's Manual - Page 24
    should be no more than 60 Watts. - Use a heavy duty service bulb for longer life. • Screw 1 bulb into each socket. 2. Lens. • Select a white (lamp) cover. • On the power head end nearest the garage door, line up lamp lens tabs on power head with corresponding slots in lens (Fig. 9-1). • Slide lens
  • Genie QuietLift 800 | Owner's Manual - Page 25
    repairs to cables, spring assemblies, and other hardware. 8. SAVE THESE INSTRUCTIONS. If you have any questions, please do not hesitate to contact Genie® customer service at: 1.800.354.3643 10 MAINTENANCE WARNING • Garage door hardware (springs, cables, brackets, pulleys, etc.) are under extreme
  • Genie QuietLift 800 | Owner's Manual - Page 26
    FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM Opener circuit peut entraîner des chocs électriques. Disconnect power from opener prior to removing cover. Desconecte la electricidad del WARNING ADVERTENCIA AVERTISSEMENT RED ROUGE ROJO MOTOR MOTEUR MOTOR GREEN VERT VERDE 123 BLACK NOIR NEGRO
  • Genie QuietLift 800 | Owner's Manual - Page 27
    TROUBLESHOOTING GUIDE - OPERATION FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM PROBLEM Opener does NOT run from Wall Control. Opener runs, but door does NOT move. Opener works from Wall Control, but NOT from remote control. WHAT TO DO • Check power source. - Plug a lamp into outlet used for
  • Genie QuietLift 800 | Owner's Manual - Page 28
    or replace wiring. - Contact The Genie Company at 1-800-35-GENIE • Reverse wire placement in power head connector. (See section 3 ) • Adjust chain/belt tension (See section 1 ). - Contact The Genie Company at 1-800-35-GENIE • Contact Genie® authorized dealer for service 28 PN# 37026500123 05/15
  • Genie QuietLift 800 | Owner's Manual - Page 29
    , il incombe à l'importateur d'en déterminer leur conformité aux lois et règles locales pouvant différer de celles des États-Unis et du Canada avant toute utilisation desdits émetteurs. Sendegeräte entsprechen allen gesetzlichen Bestimmungen in den USA und Kanada zum Zeitpunkt der Herstellung. Wir
  • Genie QuietLift 800 | Owner's Manual - Page 30
    new or reconditioned parts, or a new or reconditioned Product of the same or similar design. There are no established informal dispute resolution procedures of the type described in the Magnuson-Moss Warranty Act. PURCHASER: INSTALLATION ADDRESS: DATE PURCHASED: OPENER MODEL: REMOTE CONTROL MODEL
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
Includes: 2-Bulb Light System
Wall Console
Includes INTELLICODE
®
Remote Control
Safe-T-Beam
®
System must be installed to close door.
For use only with sectional doors.
Homelink
®
and Car2U
®
compatible
For Answers and Assistance:
1.800.354.3643
or visit www.geniecompany.com
SAVE THIS MANUAL FOR FUTURE REFERENCE
Installer:
Leave this manual
with homeowner.
PN# 37026500123,
5/15/2009
Homelink
®
is a registered trademark of
Johnson Controls Technology Company.
Car2U
®
is a registered trademark of
Lear Corporation.
© GMI Holdings, Inc. d/b/a The Genie Company
Models 2022/2024/2042
GARAGE DOOR OPENERS
ALWAYS AT YOUR COMMAND