Genie SilentMax 1000 Owner's Manual - Page 6

down arrow button - programming

Get Genie SilentMax 1000 PDF manuals and user guides View all Genie SilentMax 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

3 Required Programming TRAVEL LIMITS WARNING • Make sure doorway is in view and clear of obstacles and people to avoid injury or damage to property. • DO NOT operate this unit from wall console before LIMITS are set. Severe damage to the opener can occur. • T he shuttle MUST be engaged to carriage BEFORE setting limits. See Installation Poster (if provided) or call Customer Service at 1-800-35GENIE or visit www.geniecompany.com 3 Release down arrow button (-) and the long LED will begin flashing. PROGRAM SET + NOTE: If shuttle/bullet has NOT been engaged to carriage, do so now. See page 17. NOTE: Before setting limits confirm wall console red indicator light (or backlight) is ON. If not illuminated, check for correct wiring or the Sure-Lock switch may be activated. Closing Garage Door (Down Limits) 1 Lift the door open by hand until the shuttle/bullet engages the carriage on the rail. 4 Press and hold the down arrow button (-) until garage door is fully closed on floor, then release. PROGRAM SET + HOLD 1 2 1 2 Press and hold the down arrow button (-) for 2 seconds until the long LED comes on blue (round LED remains off). PROGRAM PROGRAM SET + SET HOLD 2 seconds 6 PROGRAM SET + NOTE: You have 30 seconds to execute each step. If you see two solid red or flashing LEDs on the Powerhead, you have run out of time and must go back to the beginning of the step and start over. You can restart as many times as necessary to complete each step. (continued next page) G999-393 Manual-ScrewBeltChain-EN indd 6 7/13/12 10 17 AM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
TRAVEL LIMITS
NOTE:
If shuttle/bullet has
NOT
been engaged to carriage, do so now.
See page 17.
NOTE:
Before setting limits
confirm wall console red indicator light
(or backlight) is ON. If not illuminated, check for correct wiring or the
Sure-Lock switch may be activated.
Closing Garage Door (Down Limits)
NOTE:
You have
30 seconds
to execute each step. If you see
two
solid red or flashing LEDs on the Powerhead
, you have run out of
time and must go back to the beginning of the step and start over. You
can restart as many times as necessary to complete each step.
(continued next page)
• Make sure doorway is in view and clear of obstacles and
people to avoid injury or damage to property.
•
DO NOT
operate this unit from wall console before
LIMITS
are set. Severe damage to the opener can occur.
• The shuttle
MUST
be engaged to carriage
BEFORE
setting limits.
See
Installation Poster
(if provided) or call Customer Service at
1-800-35GENIE or visit
www.geniecompany.com
WARNING
1
1
2
1
Lift the door open by hand until the shuttle/bullet
engages the carriage on the rail.
PROGRAM
SET
+
3
Release
down arrow button (-)
and the long LED
will begin flashing.
PROGRAM
SET
+
PROGRAM
SET
+
HOLD
4
Press and hold the
down arrow button (-)
until
garage door is fully closed on floor, then release.
PROGRAM
SET
PROGRAM
SET
+
HOLD
2 seconds
HOLD
2 seconds
2
Press and hold the
down arrow button (-)
for
2 seconds until the long LED comes on blue
(round LED remains off).
Required Programming
3
6
G999-393 Manual-ScrewBeltChain-EN indd
6
7/13/12
10 17 AM