Gigabyte GA-Z77X-UD5H Manual - Page 85

Appendix, 5-1 Configuring SATA Hard Drive(s), 5-1-1 Configuring Intel Z77 SATA Controllers

Get Gigabyte GA-Z77X-UD5H PDF manuals and user guides View all Gigabyte GA-Z77X-UD5H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Chapter 5 Appendix 5-1 Configuring SATA Hard Drive(s) RAID Levels RAID 0 Minimum Number of Hard ≥2 Drives Array Capacity Number of hard drives * Size of the smallest drive Fault Tolerance No RAID 1 2 Size of the smallest drive Yes RAID 5 ≥3 (Number of hard drives -1) * Size of the smallest drive Yes RAID 10 ≥4 (Number of hard drives/2) * Size of the smallest drive Yes To configure SATA hard drive(s), follow the steps below: A. Install SATA hard drive(s) in your computer. B. Configure SATA controller mode in BIOS Setup. C. Configure a RAID array in RAID BIOS. (Note 1) D. Install the SATA RAID/AHCI driver and operating system. (Note 2) Before you begin Please prepare: •• At least two SATA hard drives (to ensure optimal performance, it is recommended that you use two hard drives with identical model and capacity). If you do not want to create RAID, you may prepare only one hard drive. •• Windows 7/XP setup disk. •• Motherboard driver disk. •• A USB floppy disk drive (needed during Windows XP installation) •• An empty formatted floppy disk (needed during Windows XP installation) 5-1-1 Configuring Intel Z77 SATA Controllers A. Installing SATA hard drive(s) in your computer Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port on the motherboard. If there is more than one SATA controller on your motherboard, refer to "Chapter 1," "Hardware Installation," to identify the SATA controller for the SATA port. (For example, on this motherboard, the SATA3 0/1 (Note 3) and SATA2 2/3/4/5 ports are supported by the Z77 Chipset.) Then connect the power connector from your power supply to the hard drive. (Note 1) Skip this step if you do not want to create RAID array on the SATA controller. (Note 2) Required when the SATA controller is set to AHCI or RAID mode. (Note 3) When a RAID set is built across the SATA 6Gb/s and SATA 3Gb/s channels, the system performance of the RAID set may vary depending on the devices being connected. - 85 - Appendix

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
- 85 -
Appendix
Chapter 5
Appendix
5-1
Configuring SATA Hard Drive(s)
To configure SATA hard drive(s), follow the steps below:
Install SATA hard drive(s) in your computer.
A.
Configure SATA controller mode in BIOS Setup.
B.
Configure a RAID array in RAID BIOS.
C.
(Note 1)
Install the SATA RAID/AHCI driver and operating system.
D.
(Note 2)
Before you begin
Please prepare:
At least two SATA hard drives (to ensure optimal performance, it is recommended that you use two hard
•
drives with identical model and capacity). If you do not want to create RAID, you may prepare only one
hard drive.
Windows 7/XP setup disk.
•
Motherboard driver disk.
•
A USB floppy disk drive (needed during Windows XP installation)
•
An empty formatted floppy disk (needed during Windows XP installation)
•
RAID Levels
(Note 1)
Skip this step if you do not want to create RAID array on the SATA controller.
(Note 2)
Required when the SATA controller is set to AHCI or RAID mode.
(Note 3)
When a RAID set is built across the SATA 6Gb/s and SATA 3Gb/s channels, the system performance
of the RAID set may vary depending on the devices being connected.
5-1-1
Configuring Intel Z77 SATA Controllers
A. Installing SATA hard drive(s) in your computer
Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA
port on the motherboard. If there is more than one SATA controller on your motherboard, refer to "Chapter 1,"
"Hardware Installation," to identify the SATA controller for the SATA port. (For example, on this motherboard, the
SATA3 0/1
(Note 3)
and SATA2 2/3/4/5 ports are supported by the Z77 Chipset.) Then connect the power connector
from your power supply to the hard drive.
RAID 0
RAID 1
RAID 5
RAID 10
Minimum
Number of Hard
Drives
≥2
2
≥3
≥4
Array Capacity
Number of hard
drives * Size of the
smallest drive
Size of the smallest
drive
(Number of hard
drives -1) * Size of
the smallest drive
(Number of hard
drives/2) * Size of the
smallest drive
Fault Tolerance
No
Yes
Yes
Yes