Haier HH-DTB1 HH-TDS1 HH-TDB1 Manual
Haier HH-DTB1 Manual
 |
View all Haier HH-DTB1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Haier HH-DTB1 manual content summary:
- Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 1
- Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 2
Preparation Before Installation 5 3.2 Installation Position 5 3.3 Packing list 6 3.4 Installation Notice 6 3.5 Production Operation 7 4. Disassembly guide 8 (HTH-DTS1) 5. Disassembly guide 14 (HTH-DTB1) 6.General Troubleshooting 19 7. Product decomposition diagram 19 8. Circuit Diagram 20 - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 3
or repair of the electrical product needs to operation of precessional technicians. Any attempt to provide service or repair products based on this manual will result in serious consequences or death. Warning Range hood must be installed, disassembled or maintained by professional Prohibit person - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 4
't exhaust waste gas to the Execution wall, loft or garage. There is a fire risk if cleaning is not carried out in accordance with the Strict instructions. Execution Keep a good habit to turn off gas hob and gas valve if go outside, sleep or finish operation. Replace or check gas pipe regularly - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 5
Notice Because the installation is difficult and hood is heavy, the installation shall Strict be executed by professional person based on manul. Execution Don't break electric wire or other invisible equipment when cutting Strict something or drilling holes on ceiling. Execution When range hood is - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 6
2.Product Overview 2.1 Product Parameter Model Power Supply Total Pressure Efficiency Nominal Wind Pressure Turbo Airflow Max static pressure HH-DTS1/HH-DTB1 Noise 220-240V~ 50Hz Rated Power Input ≥23% Rated Main Motor Power Input 350Pa Lamp Power(max) 1200m3/h Grease Absorption Factor - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 7
The minimum distance between the bearing surface of cooking appliance and the lowest part of hood is 650mm (larger space specified in the installation instruction of gas hob shall be considered, if any; the distance for electric cooker may be reduced appropriately, depending on the actual situations - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 8
the hood, install the cup on the filter mesh. Name Operation Manual Outer outlet Oil Cup Quantity 1 piece 1 pair 1 piece 3.4 If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. Don't stretch, change - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 9
3.5 Use Instruction (HH-DTB1) (HH-DTS1) Note: All the LED lights are turned on after power-on, they will go out after about 2 seconds and a beep sounds, - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 10
4. Disassembly guide Range Hood HH-DTS1 4-1. Oil cup Remove the oil cup from the slot in the horizontal direction. 8 - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 11
4-2.Filter Disassemble the screw,then take out the filter. 4-3.Chimneycover Disassemble 4 screws,then take out the chimney cover. 9 - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 12
4-4.Back cover of blowercase Disassemble10 screws,then take out the Backcover of blower case. 4-5. The nut Remove 6 screws, take out the motor box ring, and then turn the nut clockwise by hand to take out the nut. 10 - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 13
4-6.The propellor Take out the Propellor. 4-7.Glass panel & LED light Push the glass panel horizontally, disconnect all the corresponding wire connectors, and remove the LED light from the inside and out with your handsfor replacement. 11 - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 14
4-8.Butterfly valve Disassemble the screw,then can take out the butterfly valve. 12 - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 15
4-9.Motor Disassemblethe screw ( the backside of the blower case and the exhaust position), then take out the plastic blower box, then can arrange repair / replace the motor. 13 - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 16
5. Disassembly guide HH-DTB1 5-1.Oil cup Remove the oil cup from the slot in the horizontal direction. 14 - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 17
5-2. Filter Disassemble the screw,then take out the filter. 5-3.Chimney cover Disassemble the screw on the top, the take out the upper chimney cover. 15 - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 18
5-4.The nut Remove 6 screws, take out the motor box ring, and then turn the nut clockwise by hand to take out the nut. 5-5. Propellor Takeout the Propellor. 16 - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 19
5-6. Glass plate & LED light Two hands holding the glass plate, then pull it out forward or backward slightly, disconnect all the corresponding wire connectors, and remove the LED light from the inside and out with your hands for replacement. 17 - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 20
5-7.Butterfly valve Disassemble the screw,then can take out the butterfly valve. 5-8.Motor Disassemblethe screw ( the backside of the blower case and the exhaust position), then take out the plastic blower box, then can arrange repair / replace the motor. 18 - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 21
6.General Troubleshooting No. Fault Phenomenon Fault Cause Elimination Methods No response by pressing any switch Power plug is not well connected 1 (e.g. impeller does not rotate, lighting lamp - Haier HH-DTB1 | HH-TDS1 HH-TDB1 Manual - Page 22
HH-DTB1 8.Circuit Diagram CONTROL BOARD POWER BOARD LED MOTOR M CAPACITOR 6μF/ 450V~ 20 L N E 220-240V~50Hz
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
 |
 |
