Haier HW-18HA03 User Manual
Haier HW-18HA03 Manual
 |
View all Haier HW-18HA03 manuals
Add to My Manuals
Save this manual to your list of manuals |
Haier HW-18HA03 manual content summary:
- Haier HW-18HA03 | User Manual - Page 1
Controlled Window Type Room Air Conditioner OPERATION MANUAL HW-09CC03 HW-09CD03 cL-3 HW-09CA12 HW-12CA03 HW-12HA03 o HW-12HAO4 HW-12eA03 HW-12eA04 HW-18HB03 AW094AAMBA AW122AAACA AW124AAMBA HW-12CA13 • Please read this operation manual before using the air conditioner. 7465703 H - Haier HW-18HA03 | User Manual - Page 2
/-RC For cooling only type, heating temperature range is invalid. 2. If the supply cord is damaged. it must be replaced by the manufacturer or its service agent or a similar qualified person. An extend cord is not recommended. 3. If the fuse on PC board is broken, please change it with the type - Haier HW-18HA03 | User Manual - Page 3
Description of the parts Machine body HW-12CA01 HW-I2cA03 AW094AAMBA IlW.12CA13 For models: BW-1211A03 FIW•18HBO3 AWI 22AAACA HW12HA04 NW-1244%04 AWI 24AAMBA Front panel Air inlet grating(indoor side) Mr outlet (indoor side) Air inlet (outdoor side) Display panel Operation cover Power plug Air - Haier HW-18HA03 | User Manual - Page 4
Description of the parts For models: HW-09CCO3 HW-09CA12 Inlet grating of air Outlet grating of air Time Indicator Lights up when Timer switch is sct on "ON-or "OFF" position. Power indicator Lights up when "ON/OFF button on remote controller is pressed. • • Operation mode indicator Ugh s up - Haier HW-18HA03 | User Manual - Page 5
Remote controller Display Operation r ( Signal indicator ) Lights up when sending a signal to the unit Temp.indicator To show temp. setting selected (Timer indicator To show timer mode display (TiMe display To show the number of hour selected to timer ON/OFF Operation mode indicator / To show - Haier HW-18HA03 | User Manual - Page 6
Parts and Functions The appearance is different by models. Inserting Dry Batteries Tvo R-03 dry batteries Reset Button Note: I) Use two new dry batteries of the same brand and type. 2) When the remote controller is not active after dry batteries have been replaced, press with a thin stick the - Haier HW-18HA03 | User Manual - Page 7
Auto mode 1. Start Press ON/OFF button 2. Select operation mode Press the "MODE" button. Every time the button is pressed, operation mode changes in the following order. AUTO -a-COOL DRY -0- FAN Select "Auto" mode. 3. Fan speed selection Press the FAN speed button. Every time it is pressed, Fan - Haier HW-18HA03 | User Manual - Page 8
Cooling operation I. Start Press ON/OFF button 2. Select operation mode Press the "MODE" button. Every time the button is pressed, operation mode changes in the following order. AUTO -•- COOL -0- DRY -4- FAN Select "cool" mode. 3. Select temp. setting S Select desired temp., by using "TEMP." - Haier HW-18HA03 | User Manual - Page 9
Dry Mode I. Start Press ON/OFF button 2. Select operation mode Press the "MODE" button. Every time the button is pressed. operation mode 25 changes in the following order. I AUTO --0- COOL -g- DRY -0- FAN Select "DRY" mode. Change air flow direction if necessary. 3. Stop Press "ON/OFF" - Haier HW-18HA03 | User Manual - Page 10
Fan operation 1. Start Press ON/OFF button 2. Select operation mode Press the "MODE" button. Every time the button is pressed, operation mode changes in the following order: re- AUTO --a- COOL DRY -a- FAN Select "Fan" mode. 1 1 This "Fan" is substituted by "HEAT" for heat Mb- type air - Haier HW-18HA03 | User Manual - Page 11
Heat operation Vk This function is only for heat pump. The other functions are the same. 1. Stan Press ON/OFF button 2. Select operation mode Press the "MODE" button. Every time the button is pressed, operation mode changes in the following order. AUTO--0- COOL-0- DRY-0- HEAT Select "Heat" mode. - Haier HW-18HA03 | User Manual - Page 12
Sleep mode setting 1. Start unit and confirm its operation mode. In thy and fan mode, there is no sleep function. 2. Select SLEEP function I Press the "TIMER" button. Every time the button is pressed: it changes in the following order r SLEEP - 0- TIMER OFF -►TIMER ON - IP. BLANK Select " - Haier HW-18HA03 | User Manual - Page 13
Timer operation With this function, unit will start or stop at the time you want. I. Stan unit and confirm its operation mode. If it's not started. start it and select desired operation mode. 2. Select Timer function Press the "TIMER" button. Every time the button is pressed; it changes in the - Haier HW-18HA03 | User Manual - Page 14
adjusts the left/right air direction. Push again, the plate will stop at its present position. Upward/ downward adjusting Tum the horizontal guide plate gently to adjust the upward/downward air direction. (As per the above picture). P( Emergency running If the remote controller is lost - Haier HW-18HA03 | User Manual - Page 15
Function introduction 3 minutes delay function After the conditioner is switched off, the protection device will make the compressor perform 3 minutes delay before switching on the machine. Cold air preventing In heating, to prevent the blowing of cold air, the fan will pause for a while after the - Haier HW-18HA03 | User Manual - Page 16
Usage musts Suitable indoor temperature. Cleaning of the air filter. IGRItf[li1YK Close the doors and windows during running _. Use the timer reasonably. -_ H'w•::a-: . . ) ) a Do remember the following: r Do not spray water on the machine. . Do not pull the power line with hands. ^• 3 • ♦ - Haier HW-18HA03 | User Manual - Page 17
Maintenance Cleaning of the air filter (Not for the model HW-09CA12, HW-09CC03) I. Push down the "PUSH" key at the two ends of the lower part of the air inlet grating. Release it and the 01: filter will jump up from the air inlet grating. / Nip the air filter and lift for about 5mm gently, thenpull - Haier HW-18HA03 | User Manual - Page 18
following material in order to decrease pollution: • petrol, detergent. Do not pour water on the machine to p prevent electric shock or mechanical trouble. 0 Van' 0 Hot waterabove 40Cmay cause disoaloratitm of the shell or deformation. Cleaning of the shell and remote controller *Wipe the shell - Haier HW-18HA03 | User Manual - Page 19
Trouble shooting Before sending to repair, please first check the following: Phenomenon Reason Switch on the machine but it does not work immediately. If the machine - Haier HW-18HA03 | User Manual - Page 20
Installation instruction Selection of the installation position I. Select position where the sure to use specific power circuit. The enclosed accessories of the conditioner are: 0 Name Manual Water outlet pipe Drain elbow Rubber lid Seal ring Drain Fan 0S4cr_e,w Remote battery au controller - Haier HW-18HA03 | User Manual - Page 21
Installation process 1. Make the wall hole or window hole (see Fig.!). A B HW-09xxx AW094AAMBA 350 530 1-RV-12xxx 410 570 AW122AAACA AW124AAMBA HW-12CA13 HW-18xxx 438 670 2. Fix the prefabricated iron frame to stable position by expansible screws. 3. Take out the conditioner and - Haier HW-18HA03 | User Manual - Page 22
Installation process 9. After installation of all the accessories, put the whole machine on the iron frame. If there's water outlet flexible pipe, lead the pipe to needed position (see Fig.4). 10. Fill any distance between the wall hole and the machine body with flexible sponge rubber strip to
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
 |
 |
Remote
Controlled
Window
Type
Room
Air
Conditioner
OPERATION
MANUAL
HW-09CC03
HW-09CD03
HW-09CA12
HW-12CA03
HW-12HA03
HW-12HAO4
HW-12eA03
HW-12eA04
HW-18HB03
AW094AAMBA
AW122AAACA
AW124AAMBA
HW-12CA13
•
Please
read
this
operation
manual
before
using
the
air
conditioner.
7465703
H
cL-3
o