Harbor Freight Tools 60338 User Manual

Harbor Freight Tools 60338 - 900 Peak/700 Running Watts Manual

Get Harbor Freight Tools 60338 - 900 Peak/700 Running Watts PDF manuals and user guides View all Harbor Freight Tools 60338 manuals
Add to My Manuals
Save this manual to your list of manuals

Harbor Freight Tools 60338 manual content summary:

  • Harbor Freight Tools 60338 | User Manual - Page 1
  • Harbor Freight Tools 60338 | User Manual - Page 2
    which, if not avoided, could result in minor or moderate injury. Addresses practices not related to personal injury. IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING - When using tools, basic precautions should always be
  • Harbor Freight Tools 60338 | User Manual - Page 3
    flame. 8. Do not touch engine during use. Let engine cool down before service or storage. 9. Never store fuel or other flammable materials near the engine. the generator as a power source. Always read and adhere to the instruction manual of the product to be powered, to make sure that it can
  • Harbor Freight Tools 60338 | User Manual - Page 4
    34. Use the generator, accessories, etc., in accordance with these instructions and in the manner intended for the particular type of equipment, taking affect the generator's operation. If damaged, have the generator serviced before using. Many accidents are caused by poorly maintained equipment.
  • Harbor Freight Tools 60338 | User Manual - Page 5
    equipment is maintained. Do not attempt any service or maintenance procedures not explained in this manual or any procedures that you are uncertain while the smell of fuel hangs in the air. SAVE THESE INSTRUCTIONS. SETUP OPERATION MAINTENANCE Item 60338 For Generator technical questions, please
  • Harbor Freight Tools 60338 | User Manual - Page 6
    Protection Agency and by the California Air Resources Board (also known as CARB). For warranty information, refer to the last pages of this manual. Components and Controls Fuel Cap Ground Terminal (on other side of unit) AC Receptacle Circuit Breaker Button Air Filter Cover Power Switch Choke
  • Harbor Freight Tools 60338 | User Manual - Page 7
    wave generators. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. To ground the Generator, connect a #10 AWG grounding wire (not included) from the Grounding Terminal on the side of the unit to a grounding
  • Harbor Freight Tools 60338 | User Manual - Page 8
    SETUP Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found
  • Harbor Freight Tools 60338 | User Manual - Page 9
    should be no more than 600 watts. Under normal operating conditions subsequent maintenance follows the schedule explained in the MAINTENANCE AND SERVICING section. Item 60338 For Generator technical questions, please call 1-888-866-5797. For Engine technical questions, please call 1-800-520-0882
  • Harbor Freight Tools 60338 | User Manual - Page 10
    . The resulting number is wattage. • Never exceed the rated maximum wattage (800) for the Generator or outlet. • Refer to appliance/tool owner's manuals to determine the wattage of electrical load devices. • Long power cords and extension cords draw additional power. Keep cord length at a minimum
  • Harbor Freight Tools 60338 | User Manual - Page 11
    not use damaged equipment. If abnormal noise, vibration, or excess smoking occurs, have the problem corrected before further use. Follow all service instructions in this manual. The engine may fail critically if not serviced properly. Many maintenance procedures, including any not detailed in this
  • Harbor Freight Tools 60338 | User Manual - Page 12
    SAFETY SETUP Checking and Filling Fuel WARNING! TO PREVENT SERIOUS INJURY FROM FIRE: Fill the fuel tank in a well-ventilated area away from ignition sources. If the engine is hot from use, shut the engine off and wait for it to cool before adding fuel. Do not smoke. 2.5 FLUID OUNCES 2-CYCLE OIL
  • Harbor Freight Tools 60338 | User Manual - Page 13
    SAFETY SETUP Spark Plug Maintenance 1. Disconnect spark plug cap from end of plug. Clean out debris from around spark plug. 2. Using a spark plug wrench, remove the spark plug. 3. Inspect the spark plug: If the electrode is oily, clean it using a clean, dry rag. If the electrode has deposits on
  • Harbor Freight Tools 60338 | User Manual - Page 14
    SAFETY SETUP Troubleshooting Problem Engine will not start Possible Causes Probable Solutions FUEL RELATED Tighten head. If that does not remedy problem, replace head gasket. Follow all safety precautions whenever diagnosing or servicing the equipment or engine. OPERATION MAINTENANCE Page
  • Harbor Freight Tools 60338 | User Manual - Page 15
    SAFETY SETUP Troubleshooting (cont.) Problem Engine misfires Engine stops suddenly Engine stops timing, deposit buildup, 3. Have qualified technician diagnose worn engine, or other mechanical problems. and service engine. 1. Impure or low quality gasoline/oil mixture 1. Fill fuel tank with
  • Harbor Freight Tools 60338 | User Manual - Page 16
    OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES AM6 x 60) Intake Gasket Carburetor Carburetor Gasket (B) Carburetor Gasket (A) Supporting Plate Compression Spring Cross Round Head Bolt (M6 x 40) Rod
  • Harbor Freight Tools 60338 | User Manual - Page 17
    Assembly Diagram SAFETY SETUP OPERATION MAINTENANCE Record Product's Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement
  • Harbor Freight Tools 60338 | User Manual - Page 18
    Wiring Diagram SAFETY SETUP OPERATION MAINTENANCE Limited 90 Day Warranty Harbor freight tools co. Makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and
  • Harbor Freight Tools 60338 | User Manual - Page 19
    due to failure to follow the maintenance and operating instructions set forth in the Owner's Manual including, but not limited to: Your emission control to a HFT warranty station as soon as a problem exists. Contact the HFT Customer Service department at the number below to make shipping
  • Harbor Freight Tools 60338 | User Manual - Page 20
    3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20