Harman Kardon DPR 1005 Owners Manual
Harman Kardon DPR 1005 Manual
 |
View all Harman Kardon DPR 1005 manuals
Add to My Manuals
Save this manual to your list of manuals |
Harman Kardon DPR 1005 manual content summary:
- Harman Kardon DPR 1005 | Owners Manual - Page 1
® Power for the Digital Revolution.® DPR 1005 DIGITAL PATH RECEIVER OWNER'S MANUAL - Harman Kardon DPR 1005 | Owners Manual - Page 2
DPR 1005 DIGITAL PATH RECEIVER 3 Introduction 4 Important Safety Information 4 Unpacking 5 Front-Panel Controls 8 Rear-Panel Connections 11 Main Remote Control Functions 15 Zone II Remote Control Functions 16 Installation and Connections 19 System Configuration 19 Speaker Placement 19 - Harman Kardon DPR 1005 | Owners Manual - Page 3
Harman Kardon DPR 1005, you are about to begin many years of listening enjoyment. Thanks to its completely digital path system, the DPR 1005 is truly a receiver for the new millennium. The DPR 1005 has a wide range of features and options that accommodate virtually any combination of speakers, room - Harman Kardon DPR 1005 | Owners Manual - Page 4
Before Use Your DPR 1005 has been designed for use with 120-volt AC current. Connection to a line voltage other than that for which it is intended can create a safety and fire hazard and may damage the unit. If you have any questions about the voltage requirements for your specific model, or about - Harman Kardon DPR 1005 | Owners Manual - Page 5
instructions that refer to this illustration, a larger copy may be downloaded from the Product Support section for this product at www.harmankardon.com. The following controls and indicators are available on the DPR 1005 . The specific modes will vary based on the number of speakers available, the - Harman Kardon DPR 1005 | Owners Manual - Page 6
automatically switch the DPR 1005 to the specific combination of input sources and surround mode selected, more than one indicator may light. (See page 33 for more information.) ( Remote Sensor Window: The sensor behind this window receives infrared signals from the remote control. Aim the remote - Harman Kardon DPR 1005 | Owners Manual - Page 7
‹/› Buttons ! to enter the desired boost or cut setting. See page 30 for more information on the tone controls. C Speaker Selector Button: Press this button to begin the process of configuring the DPR 1005 for the type of speakers it is being used with. For complete information on configuring the - Harman Kardon DPR 1005 | Owners Manual - Page 8
instructions that refer to this illustration, a larger copy may be downloaded from the Product Support Remote IR Input 33 Remote IR Output 34 A-BUS Connector 35 FM Antenna Jack 36 AM Antenna Terminals NOTE: To assist in making the correct connections for multichannel input, output and speaker - Harman Kardon DPR 1005 | Owners Manual - Page 9
audio and composite or S-Video jacks of a video device to these jacks. The DPR 1005's remote control has a satellite receiver as the default for this input, but you may connect any video source such as a VCR, HDTV receiver, personal video recorder, or other device to these inputs. Note that if the - Harman Kardon DPR 1005 | Owners Manual - Page 10
the receiver to serve other remote controlled devices. Connect this jack to the "IR IN" jack on Harman Kardon (or other compatible) equipment. 34 A-BUS Connector: Connect this jack to an optional A-BUS®-certified remote room keypad or amplifier to extend the multiroom capabilities of your DPR 1005 - Harman Kardon DPR 1005 | Owners Manual - Page 11
any device to the jack. • To make it easier to follow the instructions that refer to this illustration, a larger copy may be downloaded from the Product Support section for this product at www.harmankardon.com. DPR 1005 k j i h fg d e c b a Z Y X W V T U S R MAIN REMOTE CONTROL FUNCTIONS 11 - Harman Kardon DPR 1005 | Owners Manual - Page 12
DPR 1005 and most Harman Kardon CD or DVD players and cassette decks. The remote is also capable of operating a wide variety of other products using the control codes that are part of the remote. Before using the remote with other products, follow the instructions , speakers, specific menu or - Harman Kardon DPR 1005 | Owners Manual - Page 13
remote codes for Harman Kardon DVD players so that you may control a compatible player even when the remote is directly controlling the DPR, a TV set, or a cable or satellite set-top box. J Main Transport Controls: These buttons have no direct function on the DPR 1005 but are used when the remote - Harman Kardon DPR 1005 | Owners Manual - Page 14
then follow the instructions as displayed in the LCD display. (For complete information, see page 27.) j EzSet Microphone Sensor: The microphone sensor that is used by the EzSet system is behind the three slots at the top of the remote control. When using EzSet to calibrate the DPR 1005, be certain - Harman Kardon DPR 1005 | Owners Manual - Page 15
the instructions that refer to this illustration, a larger copy may be downloaded from the Product Support section control the Fast Play or Fast Reverse functions of compatible Harman Kardon CD, DVD or cassette decks in the same room, or from a remote room when an IR link is connected to the DPR 1005 - Harman Kardon DPR 1005 | Owners Manual - Page 16
supporting feet. testing speakers, even if the speakers are a different distance from the DPR 1005 instructions furnished with the speaker remote control has the commands for the Video 3 inputs set to control a cable set-top box and the commands for the Video 4 inputs set to control a satellite receiver - Harman Kardon DPR 1005 | Owners Manual - Page 17
by following the instructions for "Learning Remote IR Input jack on Harman Kardon or other compatible equipment. Multiroom IR Link The remote room IR receiver should be connected to the Multiroom IR Input U jack on the DPR 1005's rear panel. If other Harman Kardon compatible source equipment is part - Harman Kardon DPR 1005 | Owners Manual - Page 18
or module that is in the remote room to the DPR 1005 using standard Category 5 wiring that is properly rated for the in-wall use specific to the installation. Terminate the wiring at the receiver end to a standard RJ-45 connector in compliance with the instructions furnished with the A-BUS module - Harman Kardon DPR 1005 | Owners Manual - Page 19
speakers should be placed so that their tweeters are no more than 24" above or below the tweeter in the center channel speaker. Depending on the specifics of your room acoustics and the type of speakers instructions DPR 1005's bass management system for the type of speakers Front-Panel Control Door @ - Harman Kardon DPR 1005 | Owners Manual - Page 20
they are properly configured to reflect the use of digital or analog inputs, the type of speakers installed and the surround mode specifics of your home theater system. Remember that since the DPR 1005 memorizes the settings for each input individually, you will need to make these adjustments for - Harman Kardon DPR 1005 | Owners Manual - Page 21
if you wish to associate a specific product brand name with the press the ⁄/¤ Navigation Button o on the remote so that the ➔ cursor is pointing to channel is in use. The DPR 1005's Auto Polling feature allows you digital input assignment. An exclusive Harman Kardon feature is the ability to switch - Harman Kardon DPR 1005 | Owners Manual - Page 22
specification for your speakers. This information is often found on a label attached to the speaker, and it is usually shown in the owner's manual that came with your speakers. If you cannot find the information for your speakers, consult the manufacturer's Web site or customer service the DPR 1005, - Harman Kardon DPR 1005 | Owners Manual - Page 23
speakers are present. In addition, some of the modes available in the DPR 1005 The following paragraphs detail the instructions needed for modes with multiple or through the front-panel or remote controls as shown on page 31. MODE: DOLBY DIGITAL CENTER WIDTH: --DIMENSION: --PANORAMA: --NIGHT: OFF - Harman Kardon DPR 1005 | Owners Manual - Page 24
If you are in doubt as to which category describes your speakers, consult the specifications in the speakers' owner's manual, or ask your dealer. This menu screen also allows you to enter the settings for the DPR 1005's Quadruple Crossover feature which allows a different crossover point to be used - Harman Kardon DPR 1005 | Owners Manual - Page 25
particular input source for which you are configuring your speakers, the DPR 1005 will not make the LARGE option available for the center speaker. This is due to the requirements of Logic 7 processing, and does not indicate a problem with your receiver. When NONE is selected, no signals will be sent - Harman Kardon DPR 1005 | Owners Manual - Page 26
speaker position, the DPR 1005 is among the few receivers that allows you to adjust the delay for the combined output of all speakers to the Surround speakers only. To set the delay time for a specific input, the DELAY SL :10ft SR :10Ft SUB:10ft UNIT :FEET METER A/V SYNC DELAY:0mS BACK TO MASTER - Harman Kardon DPR 1005 | Owners Manual - Page 27
installed to establish the initial level settings. Using EzSet Harman Kardon's exclusive EzSet remote makes it possible to quickly and accurately set the DPR 1005's output levels without the use of a sound-pressure meter, although manual adjustment is also available. However, for the easiest setup - Harman Kardon DPR 1005 | Owners Manual - Page 28
manually, either to set them to a specific level with an SPL meter, or to make fine tuning adjustments to the levels obtained using the EzSet remote. * CHANNEL ADJUST * → FL :0 dB SBR :0 dB CEN :0 dB SBL :0 dB FR :0 dB SL :0 dB SR :0 dB SUB :0 dB CHANNEL RESET :OFF ON TEST TONE - Harman Kardon DPR 1005 | Owners Manual - Page 29
or different sources or speakers, or if you wish to change a setting to better reflect your listening taste, simply follow the instructions for changing the settings for that parameter as shown in this section. Having completed the setup and configuration process for your DPR 1005, you are about to - Harman Kardon DPR 1005 | Owners Manual - Page 30
up for a few seconds. This is normal, and it is part of the unit's power-on self test. NOTE: After pressing one of the Input Selector Buttons dXhç∂ to turn the unit on, press the AVR Selector e∫ to set the remote control to the DPR 1005 functions. To turn the unit off, simply press the Standby - Harman Kardon DPR 1005 | Owners Manual - Page 31
choose the specific individual surround mode. To select a surround mode using the remote, press control. To listen to a program in traditional two-channel stereo, using the front left and front right speakers DVDs. This does not indicate a problem with the DPR 1005, as those players cannot pass - Harman Kardon DPR 1005 | Owners Manual - Page 32
specific EX encoding is not available to provide the additional channel, the special algorithms will derive a 6.1/7.1 output. DTS 5.1 When the speaker as a source for the remote room. Logic 7 Cinema Logic 7 Music Logic 7 Enhance Exclusive to Harman Kardon for receivers, Logic 7 is an advanced - Harman Kardon DPR 1005 | Owners Manual - Page 33
remote or front-panel controls, as outlined in this manual. Next, press the Digital Select Button pE and then using the ⁄/¤ Navigation Button o on the remote DPR 1005 will display a message to indicate the type of bitstream being received the subwoofer output when the speaker configuration is set to - Harman Kardon DPR 1005 | Owners Manual - Page 34
Speaker/Channel Indicators In addition to the bitstream indicators, the DPR 1005 features channel-input indicators that show how many channels of digital information are being received is playing by pressing the Night Mode Button T on the remote. Next, press the ⁄/¤ Navigation Button o to select - Harman Kardon DPR 1005 | Owners Manual - Page 35
the tuner receives a strong enough signal for adequate reception, MANUAL TUNED will manual tuning mode. Preset Tuning Using the remote, up to 30 stations may be stored in the DPR 1005's memory for easy recall using the front-panel controls or the remote , the DPR 1005 offers Harman Kardon's exclusive - Harman Kardon DPR 1005 | Owners Manual - Page 36
Control #rî. If you are using a disc with test signals or an external signal generator as the source used when the output levels are being trimmed, you may use the remote as an SPL meter to guide you to the correct level settings. To use the EzSet remote as an SPL meter, follow the instructions - Harman Kardon DPR 1005 | Owners Manual - Page 37
receivers, when the DPR 1005 is turned on, it will always return to the volume setting in effect when the unit was turned off. However, you may prefer to always have the DPR 1005 turn on at a specific you to have feedback on any control changes or remote commands using the video display when it - Harman Kardon DPR 1005 | Owners Manual - Page 38
U to exit the menu system. Full-OSD Time-Out Adjustment The FULL OSD menu system is used to simplify the setup and adjustment of the DPR 1005 by using a series of on-screen menus. The factory default setting for these menus leaves them on the screen for 20 seconds after a period of - Harman Kardon DPR 1005 | Owners Manual - Page 39
A-BUS modules are used, follow the instructions provided with the A-BUS remote modules or keypads. RS-232 Control The DPR 1005 is rare among A/V receivers in that it provides the capability for full bidirectional remote control with confirmation control acknowledgement from compatible computers or - Harman Kardon DPR 1005 | Owners Manual - Page 40
IR Output Jack W on the DPR 1005 is connected to an IR Input jack on compatible Harman Kardon audio components such as CD, DVD or cassette players, the transport functions of those machines may also be controlled using the Transport Controls tuƒ©˙∆ on either remote control. To turn the system off - Harman Kardon DPR 1005 | Owners Manual - Page 41
is also preprogrammed to operate most recent Harman Kardon DVD players and changers, CD players and changers, CD recorders and cassette decks. The codes for other brand devices may be programmed into the DPR 1005 remote using its extensive library of remote codes or a head-to-head learning process - Harman Kardon DPR 1005 | Owners Manual - Page 42
remote manually. To automatically search through the codes that are available for a specific device type (e.g., DVD, VCR), follow these steps: 1. Turn on the power to the device you wish to program into the DPR remote if you are repeating the procedure, as instructed by the LCD screen in Figure 28. - Harman Kardon DPR 1005 | Owners Manual - Page 43
the new name for the key following the instructions shown in the Renaming Individual Keys section of this manual on page 49. If you find it remote to control the device you have selected. However, in some circumstances you may have configured your system so that the devices connected to the DPR 1005 - Harman Kardon DPR 1005 | Owners Manual - Page 44
manual entry. Continue the process as outlined in the next few steps, remembering that if the codes for your specific device are not found, you may select any brand and then "learn" the proper codes into the DPR remote As shown in the instructions that will appear on be sent out as part of the macro. - Harman Kardon DPR 1005 | Owners Manual - Page 45
line shows the number of macro steps available of 20 possible steps. Following the instructions on the remote's LCD screen, press the first key you wish to be transmitted in the macro. In our example, we first want the DPR 1005 to turn on, so the Power Button 1 should be pressed. POWER ON 00 - Harman Kardon DPR 1005 | Owners Manual - Page 46
/Down) to link to a different device. For example, if your TV, cable box or satellite receiver is connected through the DPR 1005, you will most likely want to use the DPR 1005's volume control commands even when the remote has been set to issue all other commands for the video device. "Punch-through - Harman Kardon DPR 1005 | Owners Manual - Page 47
. PUNCH-THROUGH TV - Harman Kardon DPR 1005 | Owners Manual - Page 48
easier if the displays shown in the remote's LCD screen are customized to reflect the specific characteristics of a playback source's brand name or the new function given to a specific button when one remote's controls are programmed into the DPR remote. The DPR remote allows you to change the name - Harman Kardon DPR 1005 | Owners Manual - Page 49
• When a key is renamed it will only apply to the specific device selected in Step 4. The same key may be renamed as needed for each individual device with which it is used. Resetting the Remote Depending on the way in which the remote has been programmed, there may be a situation where you wish to - Harman Kardon DPR 1005 | Owners Manual - Page 50
Button q will remain illuminated in red. Press the ⁄/¤ Navigation Button o until USER RESET appears on the bottom line of the LCD screen, as shown in Figure 77. MAIN MENU USER RESET Figure 77 3. Press the Set Button q to reset the remote. Note that once the Set Button is pressed the process may not - Harman Kardon DPR 1005 | Owners Manual - Page 51
• Amplifier is in protection mode due to internal problems • Check speaker wire connections for shorts at receiver and speaker ends • Contact your local Harman Kardon service center No sound from surround or center speakers • Incorrect surround mode • Input is monaural • Incorrect configuration - Harman Kardon DPR 1005 | Owners Manual - Page 52
DPR 1005 TECHNICAL SPECIFICATIONS Video) General Power Requirement Power Consumption Dimensions Width Height Depth Weight 520-1720 feet and chassis. All features and specifications are subject to change without notice. Harman Kardon Harman International Industries, Incorporated Part No. ZKD0301HA00-9
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
 |
 |
DPR 1005
DIGITAL PATH RECEIVER
OWNER’S MANUAL
Power for the Digital Revolution
.
®
®