Hayward AQR940 AquaRite-900-Quick-Reference-Guide-092624RevA
Hayward AQR940 Manual
 |
View all Hayward AQR940 manuals
Add to My Manuals
Save this manual to your list of manuals |
Hayward AQR940 manual content summary:
- Hayward AQR940 | AquaRite-900-Quick-Reference-Guide-092624RevA - Page 1
Reference Guide AquaRite 900 Display Readings Average Salt Level (default) 1. Water Temperature (within cell) 2. Cell Voltage (22-32 VDC) 3. Cell Amperage (how well the cell IS or IS NOT working) 4. Desired Output % (% of cell time ON) 5. Instant Salt (what system is calculating for salt during - Hayward AQR940 | AquaRite-900-Quick-Reference-Guide-092624RevA - Page 2
Quick Reference Guide - Programming Recalibrate Average Salt Turn the system O and back to Auto Push the Diagnostic button until Instant Salt appears on display (wait until it stabilizes then proceed to next step) While showing Instant Salt, ip main toggle switch from Auto, up to Super Chlorinate - Hayward AQR940 | AquaRite-900-Quick-Reference-Guide-092624RevA - Page 3
AquaRite 900 Lecturas de la pantalla El Promedio de Sal 1. La Temperatura de la agua (dentro de la Celula) 2. Voltaje de la Celula (22-32 VDC) 3. Corriente de la Celula (Como bien funciona o no funciona la Celula) 4. % de Salida Deseada (% de tiempo la Celula funciona) 5. Salinidad Instantanea (Lo - Hayward AQR940 | AquaRite-900-Quick-Reference-Guide-092624RevA - Page 4
Inspeccione y limpie la Celula; presione el boton diagnostico para 3 a 5 segundos para aclarar el reloj de las 500 horas To take a closer look or see other Hayward products please go to: www.hayward.com or call 1-800-432-8387 092624
-
1 -
2 -
3 -
4
 |
 |
Qu
i
c
k
Re
fe
re
n
ce
G
u
id
e
1. Water Temperature (
within cell
)
Cell size displayed, must match installed cell to ensure proper
operations (including salt calculation)
110 - 130VAC, 2A, 50/60Hz
220 - 250VAC, 1A, 50/60Hz
OR
Display Readings
Average Salt Level (
default
)
2. Cell Voltage (
22-32 VDC
)
3. Cell Amperage (
how well the cell IS or
IS NOT working
)
4. Desired Output % (
% of cell time ON
)
5. Instant Salt (
what system is calculating
for salt during chlorination cycle
)
6. Program Code (
AL 0-5 = product branding
)
7. Main Circuit Board Revision (
r 1.59
)
8. Cell Size (
t -15, t - 9, t - 5 or t - 3)
Cell Amperage (average)
If amperage = 0, the system may not be in a chlorination cycle
If amperage is low check salt level, inspect & clean cell
Pushing diagnostics button changes
from one reading to another
Pushing diagnostics button changes
from one reading to another
t-15 (TCELL940)
3.1 - 8.0 Amps
t-3
1.3 - 4.5 Amps
t-9 (TCELL925)
2.3 - 6.7 Amps
t-5
1.9 - 5.7 Amps
Change Units of Measure
Push Diagnostic button until water temperature
appears on display
If in US Standard: Salt = ppm & temp = Fahrenheit; if in Metric: Salt = g/l & temp = Celsius
While showing temperature, flip main
toggle switch from Auto, up to Super
Chlorinate then back to Auto