Hayward Aqua Plus Controls plus Chlorination Model: PL-PLUS Operation
Hayward Aqua Plus Controls plus Chlorination Manual
 |
View all Hayward Aqua Plus Controls plus Chlorination manuals
Add to My Manuals
Save this manual to your list of manuals |
Hayward Aqua Plus Controls plus Chlorination manual content summary:
- Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 1
increase. Drain and add water to decrease. Electrolytic Cell inspect & clean Refer to section in manual. Quarterly 620 Division St. Elizabeth, NJ 07207 092360D RevF Copyright © 2010 Hayward Aqua Plus® Automation and Chlorination Operation Manual for models PL-PLUS PL-PLUS-20 www.haywardnet.com - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 2
and Canada. Hayward/Goldline warrants all the above-identified pool automation and chlorination products installed on commercial swimming pools and on swimming pools outside of the US and Canada for a period of one (1) year. Likewise, Hayward/Goldline warrants all accessories and replacement parts - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 3
Automation 1 Chlorination 1 Default Display 2 Manual System Operation Filter Pump 3 Lights and Aux Outputs 4 Pool/Spa Valves 4 Service 4 Automatic System Operation (Programming) Using the Programming Buttons 5 Programming Menu Flow Chart 6 Settings Menu 7 Timers Menu 10 Configuration - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 4
one or more remote display/keypads. Chlorination With the use of the included Turbo Cell and flow switch, the Aqua Plus is also an automatic chlorine generation system for pool and/or spa sanitization. When enabled (see Configuration Menu), this operation requires a low concentration of salt (sodium - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 5
chlorinator cell. Default Display Turn power on at the main panel and turn the Aqua Plus control power circuit breaker on. The keypad will show the default display. The default display alternates between the day/time, air and pool (or spa) temperature, pool/ spa sanitizer setting, and salt level - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 6
program from then on. Manually turning off a relay works in a similar fashion. Display Heater Indicator Valve 3 Indicator Check System Indicator Service Button (main display only) Salt Level 3200ppm Heater Option Valve Check System + Service Menu > Pool/Spa Filter Lights Aux 1 Aux 2 > Menu - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 7
Cell, + to reset" as part of the rotating Default Menu. Clean the cell (see instructions, page 30) and then press the "+" button during the "Inspect Cell" display to reset the timer. • Low Salt/Minerals or Very Low Salt/Minerals -- When the salt is too low the Aqua Plus will generate less chlorine - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 8
at the pool equipment pad or the in-home remote display/keypad. Using the programming buttons There are 5 buttons on each keypad that are used for programming (refer to diagram). Display Salt Level 3200ppm Menu Button Select Desired Menu + Service Menu > Pool/Spa Filter Lights Aux 1 Aux - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 9
3 or hi-speed 2 pool filter 4 or lo-speed 2 spa lights aux1 aux2 valve3 superchlorinate chlorinator diagnostics instant salt pH/orp levels flow switch cell temperature sensor water/pool sensor air sensor solar sensor vsp speed/power main software revision display software revision chemistry sense - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 10
a pool professional. Details regarding the Configuration menu are included in both the Operation and the Installation Manual. The "Diagnostic Menu" is primarily intended for the service technician and contains information and details about the system operation that are helpful in troubleshooting, if - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 11
the number of gallons in the pool and add salt according to the chart below. A low salt level will reduce the efficiency of the sanitization and result in low chlorine production. A high salt level can cause the Aqua Plus to stop chlorinating. The salt in your pool/spa is constantly recycled and the - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 12
software revision of that particular keypad/display does not support the option and it will default to Beeper Enabled. 9 Chlorinator Operation / Water Chemistry General Water Chemistry Salt is required only if you are using the chlorinator features on the Aqua Plus Control. If you are NOT using - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 13
is connected to the Aqua Plus. Timers Menu The Timers Menu allows you to set all timeclock and countdown timers which control the automatic operation of your pool/spa system. Each timeclock has a single on/off program per day. All of the timeclocks are setup (Configuration Menu) either as "all days - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 14
of the spa period, the Aqua Plus will return to its normally programmed operation state. Set the Heater Temperature (or turn heater permanently off) 1. Press the "MENU" button repeatedly until "Settings Menu" is displayed 2. Press the ">" button repeatedly until the "Spa Heater1" or "Pool Heater1 - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 15
the system has been setup for "pool and spa". During the programmed spa time, the Aqua Plus will turn on the filter pump and move the pool/spa valves into the "spa-only" position. The heater will automatically heat the spa up to the programmed spa temperature (page 7). This programmed spa operation - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 16
menu item Chlorinator The Aqua Plus is shipped with the chlorinator enabled. The cell and flow switch must be installed and the Aqua Plus will automatically chlorinate both the pool and spa according to the desired output setting (see Settings Menu in the Operation manual). If disabled, all displays - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 17
POOL/SPA button on the display/keypad will allow the homeowner to alternate between pool and spa operation. Spa CountDn This menu will appear only if Pool/Spa Setup is set to "Pool and Spa". This setting is the time, after you manually switch the Pool/Spa valves to "Spa Only", until the Aqua Plus - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 18
and then will turn off automatically after a programmed time (see Timers Menu, Operation Manual). The AUX button can also be used to turn the output off. Low Speed of a 2-speed Filter Pump - the Aqua Plus will operate the aux relay whenever the low speed operation of the filter pump is required. It - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 19
water flowing), when the pool/spa suction return valves are in any position other than "pool only", or for the first 3 minutes after solar turns on (allows air in the solar panels to be purged). Interlock is not available for solar, low speed filter pump, super chlorinate or dimmer. Lights External - Hayward Aqua Plus Controls plus Chlorination | Model: PL-PLUS Operation - Page 20
will turn off automatically after a programmed time (see Timers Menu in Operation Manual). The LIGHTS button can also be used to turn the output off. Low Speed of a 2-speed Filter Pump - the Aqua Plus will turn on the lights relay whenever the low speed operation of the filter pump is required
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
Quarterly
Monthly
Weekly
Free Chlorine
1.0 - 3.0 ppm
pH
7.2 - 7.8
Raise desired output % to
increase, lower desired output %
to decrease -OR- increase or
decrease pump filtration time.
Too low -
add soda ash.
Too high - add muriatic acid
Alkalinity
80 - 120 ppm
Salt
2700 - 3400 ppm
Add salt as required to increase.
Add baking soda to increase.
Stabilizer
60 - 80 ppm
Add cyanuric acid to increase.
Calcium
200 - 400 ppm
Add calcium to increase.
Electrolytic Cell
inspect & clean
Refer to section in manual.
TEST
IDEAL RANGE
ADJUSTMENT REQUIRED
Drain and add water to decrease.
Add acid as required to decrease.
Automation and Chlorination
Operation Manual
for models
PL-PLUS
PL-PLUS-20
Aqua Plus
®
092360D RevF
Copyright © 2010 Hayward
www.haywardnet.com
620 Division St.
Elizabeth, NJ
07207