Hayward Aqua Rite Aqua Rite & Aqua Rite XL
Hayward Aqua Rite Manual
 |
View all Hayward Aqua Rite manuals
Add to My Manuals
Save this manual to your list of manuals |
Hayward Aqua Rite manual content summary:
- Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 1
® Electronic Chlorine Generator Installation and Operation Manual for Aqua Rite (standard) and Aqua Rite XL (inc. installation kit) G LDLINE CON TROLS www.goldlinecontrols.com 888-921-POOL - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 2
• READ AND FOLLOW ALL INSTRUCTIONS • Use Copper Conductors Only • Disconnect all AC power during electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying . • NOTICE TO USERS: This control product is to be used only in accordance with the directions - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 3
Table of Contents OPERATION General 1 Water Chemistry 1 Controls 6 Maintenance 8 INSTALLATION Mounting 9 Plumbing 10 Wiring 11 TROUBLESHOOTING Troubleshooting 14 WARRANTY Warranty 16 Aqua Rite® is a registered trademark of Goldline Controls, Inc - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 4
to 25,000 gallons (95,000 liters). Check local codes for other restrictions. The actual amount of chlorination required to properly sanitize a pool varies due to bather load, rainfall, temperature, and the pool's cleanliness. NOTE: Goldline does not recommend using the Aqua Rite to generate bromine - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 5
Saturation index The saturation index (Si) relates to the calcium and alkalinity in the water and is an indicator of the pool water "balance". Your water is properly balanced if the Si is 0 ±.2. If the Si is below -0.2, the water is corrosive and plaster pool walls will be dissolved into the water. - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 6
-3400 ppm (parts per million) with 3200 ppm being optimal. If the level is low, determine the number of gallons in the pool and add salt according to the chart on page 4. A low salt level will reduce the efficiency of the Aqua Rite® and result in low chlorine production. A high salt level can cause - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 7
Current salt Gallons and (Liters) of Pool/Spa water level 8,000 10,000 12,000 14,000 16,000 18,000 20,000 22,000 24,000 26,000 28,000 30,000 32,000 34,000 36,000 38,000 40,000 ppm (30,000) (37,500) (45000) (52,500) (60,000) (67,500) (75,000) (82,500) (90,000) (97,500) (105,000)(112,500)(120,000 - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 8
(Liters) of Pool/Spa water Current Stabilizer Level (ppm) 8,000 (30000) 10,000 12,000 (37500) (45000) 14,000 (52500) 16,000 (60000) 18,000 (67500) 20,000 (75000) 22,000 (82500) 24,000 (90000) 26,000 (97500) 28,000 30,000 32,000 34,000 36,000 38,000 40,000 (105000) (112500)(120000)(127500 - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 9
Eos is in SERVICE or TIME-OUT mode and the Main Switch and "Desired Output %" adjustment are active. NO FLOW When illuminated, the flow switch has detected no water flowing and the Aqua Rite has stopped generating chlorine. A flashing LED indicates a 15-60 second time delay period. CHECK SALT When - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 10
it to decrease chlorine level. Note: The "Desired Output %" adjustment will not function when the Aqua Rite is being controlled by a remote pool automation control. Salt Display The Salt Display shows the current salt concentration of the pool water. Readings are in ppm (parts per million). Refer - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 11
" LED remains on after a thorough cleaning, the cell may be worn and require replacement. Servicing and Cleaning the Aqua Rite cell Turn off power to the Aqua Rite before removing the electrolytic cell. Once removed, look inside the cell and inspect for scale formation (light colored crusty or flaky - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 12
with Local and NEC codes. 120/240 VAC POWER ELECTRONIC CHLORINE GENERATOR G LDLINE CONTROLS INC. FROM FROM POOL SPA TO TO SPA POOL Preparing Pool/Spa Water Refer to page 1 for recommended chemical levels. The pool's chemistry must be balanced BEFORE activating the Aqua Rite®. NOTE: If the - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 13
Aqua Rite® installation does not constitute a cross connection with the local potable water supply. Consult local plumbing codes. The flow switch and cell configurations #1 shows the flow switch can also be in front of the cell. Configurations #2 and #3 allow for chlorination of both the pool - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 14
must be shut off at the circuit breaker before performing any wiring. Be sure to follow Local and NEC electrical codes. To provide safe operation, the Aqua Rite® must be properly grounded and bonded. Input Power For stand alone operation: Wire the Aqua Rite to the LOAD SIDE of the filter pump timer - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 15
controls: Wire the Aqua Rite® DIRECTLY to 120/240VAC power (not through timer or relay). GOLDLINE, PENTAIR or POLARIS AQUA RITE (240 VAC) AQUA RITE (120 VAC) SUBPANEL GND GND NEUTRAL GROUND PCB BONDING LOOP PCB BONDING LOOP Optional Goldline, Pentair and Polaris controls: The Goldline - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 16
Polaris - Attach wires to proper screw terminals as shown below. Note that screw terminal "1" is marked on the Polaris PCB. GRN 4 Aqua Rite YEL 3 BLK 2 black yellow green note marked 1 on PCB Eos RED 1 red 13 - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 17
. The Aqua Rite is protected by a 20 amp mini ATO fuse located on the circuit board above the cell connector. 2. "Generating" LED flashing The temperature of the pool water is too high or low to operate. You can override this by switching the main switch to SUPER CHLORINATE. The Aqua Rite will - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 18
(below 2400 ppm, Check Salt LED on). - Salt level too high (High Salt LED on). - Very warm pools increase chlorine demand--increase Output %, or filter run time. - Cold water (below 50ºF) causes Aqua Rite to stop generating (Generating LED flash- ing). - Excessive scaling on cell. - High level - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 19
its Aqua Rite, Aqua Rite Pro, Aqua Trol, Aqua Logic and Pro Logic products (products with Goldline part numbers starting with AQ-RITE-, AQ-RTPRO, AQ-TROL-, AQ-LOGIC-, AQL-P-, AQL-PS-, AQL-CL-, PL-P-, PL-PS-, and HPC-2) to be free from defects in material or workmanship, under normal use and service - Hayward Aqua Rite | Aqua Rite & Aqua Rite XL - Page 20
Drain and add water to decrease. Electrolytic Cell inspect & clean Refer to section in manual. Questions? Refer to www.goldlinecontrols.com for latest manual revisions, additional information and helpful service. Or, you may visit your local Authorized Aqua Rite Dealer or call 888-921- POOL (7665
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
888-921-POOL
Electronic Chlorine Generator
www.goldlinecontrols.com
®
Installation and Operation Manual
for
Aqua Rite (standard) and Aqua Rite XL (inc. installation kit)
LD
C
G
LINE
ON TROLS