Hayward HL32950VSP VS Omni Installation Quick Start Guide

1

2

3

Mount to Wall or Flat Surface

VS Omni

TM

Installation Quick Start Guide

WWW.HAYWARD.COM

908-355-7995

Turn Over

Gray

Black

Black &

White

Red

Red &

White

Pre-Installation Checklist

Power is removed to all equipment in the system.

All safety precautions have been read in the Installation manual.

All parts listed in the Installation manual are included in the box.

All of the necessary mounting hardware has been gathered including nylon

cable ties (for pole or rebar mounting), four #8 screws (Smart Relay), and

six fasteners appropriate for mounting surface (Wiring Hub & Control Pad).

All of the necessary tools have been gathered (drill, drill bits, knife, Phillips &

flathead screwdrivers, level, wire cutters/strippers, channel lock pliers).

The Wiring Hub, Control Pad, and Smart Relay will be mounted a minimum

of 6’ horizontal distance from the pool or spa and a minimum of 4’ vertical

distance off the ground.

The Control Pad and Smart Relay will be mounted a maximum of 15’ from

the Wiring Hub.

The Control Pad will be mounted in a location that is convenient for viewing

and changing settings.

The Control Pad will be mounted with enough clearance above the enclo-

sure so that the flip door will be able to open fully.

Pool Sensor

Air Sensor

Optional Solar

Sensor or External

Input Switch

Low Voltage Heater

Push on

lever to

insert wire

Refer to manual for

sensor mounting

Remove Existing

Light Switch

Install the

Smart Relay

using wiring

information

below

Internal Volume

must be a

minimum of 16.2 in

3

Smart Relay

Communication Wiring

Stop!

Proceed with this Quick Start Guide

ONLY if your existing pump is powered

by 230VAC.

If not, refer to the VS Omni

Installation manual.

Provided Hub

Wiring Harness

L1

L2

Mounting Screws

(Not Included)

Mount the VS Omni Wiring Hub

To mount the Control

Pad, cut out and use

the template included

in the Installation

Control Pad Mounting Template

Position Control Pad cutouts over

screws and slide downwards to

lock in place.

Tighten the screws

as necessary for a snug fit.

2.85 in.

Mount the VS Omni Control Pad

Existing Timeclock

or

Breaker Panel

Existing

230VAC

Pump

Disconnect power to exist-

ing pump and use as input

power to the Wiring Hub.

Provided Hub

Wiring Harness

L2

L1

Plumb in the new VS Omni

Variable Speed Pump.

Use the provided 6’ whip to

wire the pump to the Wiring

Hub as shown.

NOTE: If using a timeclock,

set to run continuously

to assure that power is

always available to the

pump.

Variable Speed Pump

High Voltage Wiring

Low Voltage Wiring

Wiring

Hub

Wiring

Hub

Mounting #8 screws

(not included)

Mount to Wall or Flat Surface

Mount the Smart Relay

Using Hayward’s Box

Mount the Smart Relay

in a Pre-Existing Box

Red

Red/White

Black

Black/White

Gray

Neutral

Load out

No Connection

No Connection

120 VAC

Load 2 out

Load 1 out

Line 1 in

240 VAC

Line in

Connect Gray &

Red to Line 2 in

Smart Relay

Wire Colors

- OR -

Flow

Switch

Control

Pad

Valve Actuators

(Hub must be powered

by 230VAC)

Low

Voltage

Wiring

Channel

Earth

Ground

When wiring is complete, use a remov-

able foam gasket (located on the Wiring

Hub’s inside cover) to seal the low

voltage wiring channel.

Wrap it around

the low voltage wiring exit at the bottom

of the Wiring Hub and work it into the exit

slot until fully sealed.

Seal Wiring Channel With Foam Gasket

Inside Cover

Foam Gasket

The Smart Relay requires a Neutral connection if using 115 VAC. Before in-

stallation, confirm that there is a Neutral line available or run one separately.

I

f using 115 VAC,

Box Must Contain a

Neutral Connection

I

f using 115 VAC, Box Must Contain a Neutral Connection

Red

Black

White

Green

4

See Step 4 on back

page for more detail

on pump wiring

Input

Power

Hayward HL32950VSP VS Omni Installation Quick Start Guide

Hayward HL32950VSP Manual

Hayward HL32950VSP manual content summary: