Hayward HeatPro Heat Pro

Hayward HeatPro Manual

Get Hayward HeatPro PDF manuals and user guides View all Hayward HeatPro manuals
Add to My Manuals
Save this manual to your list of manuals

Hayward HeatPro manual content summary:

  • Hayward HeatPro | Heat Pro - Page 1
    PRINTED IN CANADA OWNER'S Manual 10/2009
  • Hayward HeatPro | Heat Pro - Page 2
  • Hayward HeatPro | Heat Pro - Page 3
    Service Analyzer Control 13 Operation 14 Caring for your Pool Heater 15 Initial Startup 16 Meaning of Display Codes 17 Troubleshooting 18 Requesting Assistance or Service 20 Maintenance 21 Winterizing 21 Hayward® Heat Pump Pool Heater Limited Warranty 22 International Warranty
  • Hayward HeatPro | Heat Pro - Page 4
    industry standards. All HEATPRO pool heat pumps have an electronic board with service analyzer, a titanium heat exchanger tube warranted for technology heat pump. Compared to other types of pool heaters, such as gas or oil-fired, the HEATPRO pool heat pump has a lower heating capacity on a BTU/hr
  • Hayward HeatPro | Heat Pro - Page 5
    with this guide. The return address is displayed on the front of your registration card. Simply mail it as you would a postcard. The card helps us notify you about any new information about your heater. Whenever you call to request service for your heater, you must know your complete model and
  • Hayward HeatPro | Heat Pro - Page 6
    General Safety Instructions We care for our customers We have provided important safety messages in this manual and on your heater. Always result in material damage, particularly to the product, up to the destruction of part or all of the product. WARNING The WARNING sign denotes a hazard. It calls
  • Hayward HeatPro | Heat Pro - Page 7
    clearances needed for proper operation and heating. CAUTION ! Proper pool chemistry is vital to the life of your heater. Pay particular attention to the total alkalinity and TDS. It is highly recommended that you have your pool chemistry checked often by an independent pool store. OWNER'S MANUAL 5
  • Hayward HeatPro | Heat Pro - Page 8
    Installation Instructions Location The placement of the pool heater is very important in keeping installation costs to a minimum while providing for maximum efficiency of operation, as well as allowing adequate access for service and maintenance. The pool heat pump is designed for outdoor
  • Hayward HeatPro | Heat Pro - Page 9
    be performed by a qualified electrician in accordance with local requirements. A properly-sized breaker and copper wire must be used. Check the heat pump data label for required maximum breaker size. WARNING The unit must always be powered off before opening the access panel. OWNER'S MANUAL 7
  • Hayward HeatPro | Heat Pro - Page 10
    must be placed before or upstream from the heat pump. 4. A bypass and shut-off should be installed on all systems for ease of service, maintenance and to balance the water flow. Bypasses must be installed on any system with over a 3/4 HP pool pump. (see FIG.3 for bypass plumbing) 8 OWNER'S MANUAL
  • Hayward HeatPro | Heat Pro - Page 11
    Bonding and Plumbing diagram Fig. 2 Chemical feeder Heat Pump Fig. 3 OWNER'S MANUAL 9
  • Hayward HeatPro | Heat Pro - Page 12
    Use the P_S mode on the main menu External mode: • Open contact = POOL mode • Closed contact = SPA mode Control using a switch To control the board using an external switch, follow these steps : • Turn on the heat pump. • Set POOL mode to OFF. • Set SPA mode to the desired temperature. • Access the
  • Hayward HeatPro | Heat Pro - Page 13
    on the lid of the control box as well as in this manual. Power requirements 240 V, 1 PH, 60 Hz Look at the name plate located on the heat pump to know the required amperage. Please refer to your local electrical code for additional wiring requirements. Fig. 5 L1 L2 Ground OWNER'S MANUAL 11
  • Hayward HeatPro | Heat Pro - Page 14
    Opened = no flow WS DS HP HP LP LP FLO FLO Black Black Light Blue Light Blue Purple Purple COMPRESSOR COMPRESSOR FAN FAN Black Brown Brown FAN CAP CAP S COMPRESSOR R C Yellow Yellow HGD H/C 24 VAC PS Yellow 24 Vac Red Brown Remote switch Pool (opened) Spa (closed) Black Blue 24
  • Hayward HeatPro | Heat Pro - Page 15
    Service Analyzer Control The control panel is factory set to display the temperature in Fahrenheit degrees. Celsius or Fahrenheit mode Temperature and parameter display Access to parameters Heating mode Compressor ( ) or fan ( ) running Heating mode To raise the desired temperature or to change
  • Hayward HeatPro | Heat Pro - Page 16
    can switch to POL or SPA. Once the heating mode has been programmed, it will be displayed for five seconds, and will then return to the actual pool water temperature. The lights on the right side of the display indicate the chosen heating mode. To display the temperature in °F or in °C Press the SET
  • Hayward HeatPro | Heat Pro - Page 17
    Caring for your Pool Heater How to protect your pool heater OWNER'S MANUAL 15
  • Hayward HeatPro | Heat Pro - Page 18
    the pool pump is activited. Then, you will need to set the water temperature you desire. The fan will immediately start. The compressor will start after a 3 to 4-minute delay. When the compressor is running, the HEATING/CHAUFFAGE indicator located on the right (see "Service Analyzer Control," p. 13
  • Hayward HeatPro | Heat Pro - Page 19
    problems will be detected by the service analyzer and a code will be displayed on the digital display of your heater. Display Meaning of codes OFF The desired programmed temperature point is lower than 60°F (15°C). LP & LP3 Shortage of refrigerant gas in the unit or faulty low pressure control
  • Hayward HeatPro | Heat Pro - Page 20
    Troubleshooting The pool heater is not running. Heat pump control set to OFF. Desired water temperature is reached. Main breaker is tripped. Raise temperature set point above 60°F (15°C). Unit will automatically restart when the
  • Hayward HeatPro | Heat Pro - Page 21
    There is no display and the fan is not running, but the compressor is running. Ask your electrician to verify your heat pump's power supply by checking over the L1 and L2 connections in the unit's service box. There is water around the unit. While your pool heater is in the heating mode, a large
  • Hayward HeatPro | Heat Pro - Page 22
    you still need help, follow the instructions below. Service can be obtained by calling one of these phone numbers. CANADA: 1 888 238-7665 USA: 1 908 355-7995 When asking for help, please provide a detailed description of the problem, your heater's complete model and serial number, and the purchase
  • Hayward HeatPro | Heat Pro - Page 23
    the plastic cabinet can be done with the help of a brush and soap. Winterizing First, you must turn the breaker off. The unit must be drained of all recommended to cover the heat pump to prevent snow from getting inside. A protective winter cover is also offered by your retailer. OWNER'S MANUAL 21
  • Hayward HeatPro | Heat Pro - Page 24
    Hayward® Heat Pump Pool Heater Limited Warranty The HAYWARD heat pump pool heater is warranted to be free of defects in materials and workmanship for a period of two (2) years for parts and (1) one year for labor. In the state of Florida, warranty labor is covered for (2) years. This warranty is
  • Hayward HeatPro | Heat Pro - Page 25
    International Warranty The HAYWARD heat pump pool heater is warranted to be free of defects in materials and workmanship for a period of one (1) year. The compressor is warranted for two (2) years, and the titanium tube component of the heat exchanger has a ten (10) year warranty. The above coverage
  • Hayward HeatPro | Heat Pro - Page 26
    Notes 24 OWNER'S MANUAL
  • Hayward HeatPro | Heat Pro - Page 27
  • Hayward HeatPro | Heat Pro - Page 28
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
OWNER’S Manual
PRINTED IN CANADA
10/2009