Hayward S144T1540S Model: S144T
Hayward S144T1540S Manual
 |
View all Hayward S144T1540S manuals
Add to My Manuals
Save this manual to your list of manuals |
Hayward S144T1540S manual content summary:
- Hayward S144T1540S | Model: S144T - Page 1
of actions that are unpredictable and unsafe. The NOTICE label indicates special instructions that are important but not related to hazards. SAVE THIS INSTRUCTION MANUAL Use only High Rate Sand No. 20 Silica Sand (.45mm - .55mm) HAYWARD POOL PRODUCTS, INC. 620 Division Street Elizabeth, NJ 07207 Tel - Hayward S144T1540S | Model: S144T - Page 2
instructions could result in violent separation of pump and/or filter components. Strainer cover must be properly secured to pump housing with strainer cover lock ring. Before servicing pool and spa circulation system, filters manual . WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS - Hayward S144T1540S | Model: S144T - Page 3
instructions and consult a professional electrician on how to bond pump. Also, contact a licensed electrician for information on local electrical codes for bonding requirements. Your Hayward Pro Series high-rate sand valve is manually resequenced to Rinse to install and/or service the filter. 1. The - Hayward S144T1540S | Model: S144T - Page 4
waste. INITIAL START-UP OF FILTER 1. Be sure correct amount of filter sand media is in tank and that all connections have been made and are secure and winterize pump according to pump instructions. SERVICE & REPAIRS Consult your local authorized Hayward dealer or service center. No returns may be - Hayward S144T1540S | Model: S144T - Page 5
Vari-Flo Control Valve 1 ½" Pressure Gauge Valve/Tank O-ring Flange Clamp Sand Shield Folding Lateral Assy S144T Folding Lateral Assy S164T Filter tank Assy less valve ) 1 ½" Straight Hose Adapter 2 Hose Clamp 2 FIGURE B WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS - Hayward S144T1540S | Model: S144T - Page 6
in a safe and convenient location for your records. PROBLEM SOLVING LIST REMEDY LOW WATER FLOW 1. Check skimmer (adjust as required). 3. Check surface of filter sand for crusting or caking (remove 1 " of sand if necessary). POOL WATER WON'T CLEAR UP 1. ONLY HAYWARD GENUINE REPLACEMENT PARTS - Hayward S144T1540S | Model: S144T - Page 7
should be returned, transportation paid, to the place of purchase, or to the nearest authorized Hayward service center. For further Hayward dealer or service center information, contact Hayward customer service department. No returns may be made directly to the factory without the express written - Hayward S144T1540S | Model: S144T - Page 8
Page 8 of 8 MODEL S144T, S164T THIS PAGE LEFT BLANK IS144T Rev B WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
OWNER’S MANUAL
INSTALLATION, OPERATION & PARTS
MODELS S144T, S164T
HIGH-RATE SAND FILTERS
SAVE THIS INSTRUCTION MANUAL
IS144T
Rev. B
Basic safety precautions should always be followed, including the following: Failure to follow instructions can cause severe
injury and/or death.
This is the safety-alert symbol. When you see this symbol on your equipment or in this manual, look for one of the
following signal words and be alert to the potential for personal injury.
WARNING
warns about hazards that
could
cause serious personal injury, death or major property damage and if
ignored presents a potential hazard.
CAUTION
warns about hazards that
will
or
can
cause minor or moderate personal injury and/or property damage
and if ignored presents a potential hazard.
It can also make consumers aware of actions that are unpredictable and unsafe.
The
NOTICE
label indicates special instructions that are important but not related to hazards.
HAYWARD POOL PRODUCTS, INC.
620 Division Street
Elizabeth, NJ 07207
Tel: 908-351-5400
WWW.HAYWARDPOOL.COM
Use only High Rate Sand No. 20 Silica Sand (.45mm - .55mm)