Hayward Super II All Super II models

Hayward Super II Manual

Get Hayward Super II PDF manuals and user guides View all Hayward Super II manuals
Add to My Manuals
Save this manual to your list of manuals

Hayward Super II manual content summary:

  • Hayward Super II | All Super II models - Page 1
    P/N: IS3000XAZ-05 Rev. C OWNER'S MANUAL INSTALLATION, OPERATION, & PARTS Super II™ Pump Series *50HZ Models are not UL or CSA Listed. The Hayward Super II Pump is specifically engineered for the demanding requirements of today's in-ground swimming pool/spa that is equipped with large capacity
  • Hayward Super II | All Super II models - Page 2
    Super II™ Pump Series Page 2 of 14 WARNING - Read and follow all instructions in this owner's manual and on the equipment. Failure to follow instructions can cause severe injury and/or death. IMPORTANT SAFETY INSTRUCTIONS Before installing or servicing this electrical equipment, turn power
  • Hayward Super II | All Super II models - Page 3
    motor housing and to all metal parts of swimming pool flow rate shall not exceed the values shown in the "Pipe Sizing Chart" found at the bottom of page 5 of this manual. - Never use pool or spa if any suction outlet component is damaged, broken, cracked, missing, or not securely attached. - Replace
  • Hayward Super II | All Super II models - Page 4
    for the proper installation and operation of the Hayward Super II Pump Series. The instructions in this manual MUST be followed precisely. Failure to install according to defined instructions will void warranty. Product Benefits ƒ Super-sized 180 cubic-inch basket has extra leaf-holding capacity and
  • Hayward Super II | All Super II models - Page 5
    Super II™ Pump Series__________ Product Specifications _____ Page 5 of 14 Installation Instructions WARNING - This product should be installed and serviced only by a qualified professional. Pump Location Locate pump as close to pool as practical and run suction lines as direct as possible to
  • Hayward Super II | All Super II models - Page 6
    Super II™ Pump Series __________ Pump Mounting (cont'd) _____ Page 6 of 14 WARNING - Hazardous Pressure. Pumps, filters, and other equipment/ components of a swimming pool Max Rate HP KW 1 0.75 1-1/2 1.10 2 1.55 2-1/2 1.87 3 2.20 Full Rate HP KW HAYWARD GENUINE REPLACEMENT PARTS
  • Hayward Super II | All Super II models - Page 7
    acts as a coolant and lubricant for the mechanical shaft seal. ATTENTION - NEVER run pump dry. Running pump dry may damage seals, causing leakage, flooding, and voids warranty. Fill strainer housing with water before starting motor. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
  • Hayward Super II | All Super II models - Page 8
    obstruction to avoid damage. Do NOT use water to hose off motor. ƒ Occasionally, shaft seals must be replaced, due to wear or damage. Replace with genuine Hayward seal assembly kit. See "Shaft Seal Change Instructions" in this manual. WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
  • Hayward Super II | All Super II models - Page 9
    of the two-part replacement seal. Foreign matter or improper handling will easily scratch the graphite and ceramic sealing surfaces. Removing the Motor Assembly (See Parts Diagram on page 11 of this manual for pump component locations.) 1. Remove the six (6) 3/8" x 2" housing cap screws which
  • Hayward Super II | All Super II models - Page 10
    , with flange facing towards the diffuser. 13. Place the diffuser over the impeller onto the seal plate fitting positioning lug between the two (2) guides. Replacing the Motor Assembly (See Parts Diagram on page 11 of this manual for pump component locations.) 14. Fasten motor end cover by using the
  • Hayward Super II | All Super II models - Page 11
    Super II™ Pump Series Replacement Parts Parts Diagram Page 11 of 14 Parts Listing WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
  • Hayward Super II | All Super II models - Page 12
    hose clamps are tight. ii. Check voltage to ensure that the motor is rotating at full RPM's. iii. Open housing cover and check for clogging or obstruction in suction. Check impeller for debris. iv. Remove and replace shaft seal only if it is leaking. Low Flow - Generally, Check For: 1. Clogged
  • Hayward Super II | All Super II models - Page 13
    pump housing. 4. Motor bearings noisy from normal wear, rust, overheating, or concentration of chemicals causing seal damage which will allow chlorinated water to seep into bearings wiping out the grease causing bearing to whine. Solution: All seal leaks should be replaced at once. © Hayward Pool
  • Hayward Super II | All Super II models - Page 14
    other products from Hayward: Type of In-Ground Pool: □ Vinyl □ Fiberglass □ Gunite Size of Pool □ Pump □ Filter □ Automatic Pool Cleaner □ Light □ Chlorinator □ Skimmer □ Heater □ Heat Pump □ Salt/Chlorine Generator □ Controls WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
P/N: IS3000XAZ-05
Rev. C
__________________________________________________________________________________________
OWNER’S MANUAL
INSTALLATION, OPERATION, & PARTS
*50HZ Models are not UL or CSA Listed.
Super II
™
Pump Series
The Hayward Super II Pump is specifically engineered for the demanding requirements of today’s in-ground swimming pool/spa that
is equipped with large capacity filters, heaters, and pool cleaning equipment.
The Super II is a self-priming pump that incorporates an
improved seal and impeller design that will provide many years of efficient, dependable, corrosion-free service.
The advanced design
provides superior performance while reducing maintenance requirements.
To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and completely.
WARNING
–
This product should be installed and serviced only by a qualified professional.
CAUTION
–
A
licensed
electrician MUST complete, in full, all electrical installations noted in this manual.
SAVE THIS INSTRUCTION MANUAL
Use of non-Hayward replacement parts voids warranty.
ATTENTION
INSTALLER
–
THIS
MANUAL
CONTAINS
IMPORTANT
INFORMATION
ABOUT
THE
INSTALLATION,
OPERATION,
AND
SAFE
USE
OF
THIS
PUMP
THAT
MUST
BE
FURNISHED
TO
THE
END
USER
OF
THIS
PRODUCT.
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS COULD RESULT IN SERIOUS
INJURY.
HAYWARD POOL PRODUCTS, INC.
620 DIVISION STREET
ELIZABETH, NJ
07207
(908) 351-5400
WWW.HAYWARDPOOL.COM