Hayward Turbo Cell Model: T-CELL-3

Hayward Turbo Cell Manual

Get Hayward Turbo Cell PDF manuals and user guides View all Hayward Turbo Cell manuals
Add to My Manuals
Save this manual to your list of manuals

Hayward Turbo Cell manual content summary:

  • Hayward Turbo Cell | Model: T-CELL-3 - Page 1
    configuration will cause inaccurate salt readings, improper operation, and possible system shutdown. The T-CELL-3 and GLX-CELL-3-W are designed for pools up to 15,000 gallons. They are compatible with the following models only and will NOT work with earlier versions: • AQR (Aqua Rite - all 2009 or
  • Hayward Turbo Cell | Model: T-CELL-3 - Page 2
    IMPORTANT INFORMATION Regarding Extended Pool Filtration cycles, and Low Flow Rate conditions THE AMOUNT OF CHLORINE PRODUCED BY YOUR HAYWARD/GOLDLINE SALT CHLORINE GENERATING SYSTEM IS DEPENDENT ON THE LENGTH OF TIME THAT YOUR FILTER PUMP RUNS EVERY DAY. SO, YOUR CHLORINATION SETTING SHOULD BE
  • 1
  • 2
T-CELL-3
GLX-CELL-3-W
NEW MENU SETTING REQUIRED!
You must configure your controller for use with the T-CELL-3 or GLX-CELL-3-W chlo-
rinator cell
before
attempting to operate.
Incorrect configuration will cause inaccurate
salt readings, improper operation, and possible system shutdown.
•
AQR (Aqua Rite - all 2009 or later) - firmware version 1.5 or later
•
AQR-PRO (Aqua Rite Pro) - operating with firmware 1.10 or later
•
PL-P-4 (Pro Logic P4) - operating with firmware 4.10 or later
•
PL-PS-x (Pro Logic PS) - operating with firmware 4.10 or later
Connecting to an AQR:
1.
Slide the Main Switch to the "Auto" position.
2.
Push the Diagnostic button repeatedly until "t-xx" appears on the display ("t-15" is the factory
default).
3.
To change cell type, slide the Main Switch from "Auto" to "Super Chlorinate" and back to "Auto".
Repeat this process until the “t-3” is displayed.
4.
Push the Diagnostic button to exit.
Connecting to an AQR-PRO:
1.
Verify that the firmware version is 1.10 or greater by pushing the “Info” button, then”>” repeat-
edly until the firmware revision is shown. If the firmware version is less that 1.10, the T-CELL-3
or GLX-CELL-3-W cannot be used.
2.
Access the Settings Menu by pushing the “Settings” button.
3.
Push “>” until Chlor. Config is displayed, then push “+”.
4.
Push “>” repeatedly until “Cell Type” is displayed.
5.
Push “+” or “-” until “T-CELL-3” is displayed.
6.
Exit Settings Menu by pushing the “Info” button.
Connecting to a PL-P-4 or PL-PS-x:
1.
Verify that the firmware version is greater than 4.10 by entering the Diagnostic Menu and re-
peatedly pushing the “>” until the Main Firmware revision is shown.
If the firmware version is
less that 4.10, the T-CELL-3 or GLX-CELL-3-W cannot be used.
2.
Enter the Configuration Menu.
3.
Push “>” until Chlor. Config is displayed, then push “+”.
4.
With the Chlorinator Enabled, push “>” repeatedly until “Cell Type” is displayed.
5.
Push “+” or “-” until “T-CELL-3” is displayed.
6.
Exit Settings Menu by pushing the “Menu” button.
The T-CELL-3 and GLX-CELL-3-W are designed for pools up to 15,000 gallons. They
are compatible with the following models only and will
NOT work with earlier versions: