Hayward Turbo Cell Model: T-CELL-15

Hayward Turbo Cell Manual

Get Hayward Turbo Cell PDF manuals and user guides View all Hayward Turbo Cell manuals
Add to My Manuals
Save this manual to your list of manuals

Hayward Turbo Cell manual content summary:

  • Hayward Turbo Cell | Model: T-CELL-15 - Page 1
    GLX-CELL-15-W NEW MENU SETTING MAY BE REQUIRED! The T-CELL-15 and GLX-CELL-15-W are designed for pools up to 40,000 gallons. When replacing an existing T-CELL-15 or GLX-CELL-15, no re-configuration is neccessary. Configuration of your controller may be required before using the T-CELL-15 or GLX-CELL
  • Hayward Turbo Cell | Model: T-CELL-15 - Page 2
    cycles, and Low Flow Rate conditions THE AMOUNT OF CHLORINE PRODUCED BY YOUR HAYWARD/GOLDLINE SALT CHLORINE GENERATING CELL IS RECEIVING ADEQUATE FLOW. Low flow conditions can result in insufficient water in the cell causing inefficient chlorine production. As a precaution, the cell can be installed
  • 1
  • 2
T-CELL-15
GLX-CELL-15-W
NEW MENU SETTING
MA
Y BE REQUIRED!
The T-CELL-15 and GLX-CELL-15-W are designed for pools up to 40,000 gallons. When
replacing an existing T-CELL-15 or GLX-CELL-15, no re-configuration is neccessary.
Configuration of your controller may be required before using the T-CELL-15 or GLX-CELL-15-W
chlorinator cell.
Refer to the information below. Incorrect configuration will cause inaccurate salt
readings, improper operation, and possible system shutdown.
CONFIGURATION is necessary with the following models:
•
AQR (Aqua Rite - all 2009 or later) - firmware version 1.5 or later
•
AQR-PRO (Aqua Rite Pro)
•
PL-P-4 (Pro Logic P4)
•
PL-PS-x (Pro Logic PS)
•
AQ-LOGIC-P-4 (Pro Logic P4)
•
AQ-LOGIC-PS-x (Pro Logic PS)
NO CONFIGURATION is neccessary with the following models:
•
AQ-RITE (Aqua Rite - 2008 and earlier) - firmware earlier than version 1.5
•
AQ-RITE-XL (Aqua Rite XL)
Connecting to an AQR:
1.
Slide the Main Switch to the "Auto" position.
2.
Push the Diagnostic button repeatedly until "t-xx" appears on the display ("t-15" is the factory
default). If “t-15” is displayed, skip to step 4.
3.
To change cell type, slide the Main Switch from "Auto" to "Super Chlorinate" and back to "Auto".
Repeat this process until the “t-15” is displayed.
4.
Push the Diagnostic button to exit.
Connecting to an AQR-PRO:
1.
Access the Settings Menu by pushing the “Settings” button.
2.
Push “>” until Chlor. Config is displayed, then push “+”.
3.
Push “>” repeatedly until “Cell Type” is displayed.
4.
Push “+” or “-” until “T-CELL-15” is displayed.
5.
Exit Settings Menu by pushing the “Info” button.
Connecting to an AQ-LOGIC-P-4, AQ-LOGIC-PS-x, PL-P-4 or PL-PS-x:
1.
Enter the Configuration Menu.
2.
Push “>” until Chlor. Config is displayed, then push “+”.
3.
With the Chlorinator Enabled, push “>” repeatedly until “Cell Type” is displayed.
4.
Push “+” or “-” until “T-CELL-15” is displayed.
5.
Exit Settings Menu by pushing the “Menu” button.